Vulnerabilities
All
My stack
Known exploited
Public exploit
Critical (9+)
Likely exploited (EPSS ≥ 50%)
Changed, 24 h
New, 24 h
Sort:
risk
modified
published
CVSS
EPSS
| CVE | CVSS | EPSS | Vendor, product | Description | Modified |
|---|---|---|---|---|---|
| CVE-2026-89655 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: ceph: fix UAF in __kick_flushing_caps() on cf entry freed during unlock list_for_each_entry() iterates ci->i_cap_flush_list but drops i_ceph_lock to send cap messages. During the unlock window, handle_cap_flush_ack() can acquire i_ceph_lock, detach cf entries with tid <= flush_tid from the list, release i_ceph_lock, and free them via ceph_free_cap_flush() outside any lock. When the original thread reacquires i_ceph_lock and the for-loop macro advances via cf = list_next_entry(cf, i_list), it dereferences cf->i_list.next on freed memory. The race timeline: __kick_flushing_caps() handle_cap_flush_ack() ----------------------- ----------------------- holds i_ceph_lock <--- iterates to cf (tid=10) prepares FLUSH message drops i_ceph_lock <--- __send_cap() ── FLUSH(tid=10) MDS sends FLUSH_ACK(tid=10) ---> acquires i_ceph_lock cf->tid(10) <= flush_tid(10), detaches cf from i_cap_flush_list drops i_ceph_lock ceph_free_cap_flush(cf) <- frees it! acquires i_ceph_lock <--- for-loop advances: cf = list_next_entry(cf, i_list) -- UAF on freed cf->i_list.next The cf was just sent by __kick_flushing_caps itself via __send_cap(). The MDS may respond with FLUSH_ACK quickly enough that handle_cap_flush_ack() frees cf before __kick_flushing_caps can finish the iteration. Fix by converting to a manual while loop: save the next pointer under i_ceph_lock before dropping it, then use the saved pointer after reacquiring, so the potentially-freed cf is never accessed again. | 19 Oct |
| CVE-2026-89653 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: ceph: reject export_targets ranks >= CEPH_MAX_MDS in mdsmap decode MDSMap export_targets entries are monitor controlled. check_new_map() uses each entry as a bit number in a fixed stack bitmap, so a rank outside the protocol namespace can make set_bit() write past the end of the array. Reject ranks outside CEPH_MAX_MDS while decoding the map. Do not validate against possible_max_rank here because maps may legitimately reference ranks beyond a temporarily reduced max_mds. | 19 Oct |
| CVE-2026-89651 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: ceph: bound MDSCapAuth path and fs_name decode in handle_session() handle_session() decodes the MDSCapAuth records carried by a CEPH_SESSION_OPEN message (msg_version >= 6). For each record the match.path and match.fs_name byte strings are read by first decoding a 32-bit length and then copying that many bytes with the bare ceph_decode_copy(). Unlike the surrounding fields, which all use the _safe decode variants, these two copies are not preceded by a ceph_decode_need() bounds check, and the enclosing MDSCapAuth and MDSCapMatch struct_len fields are skipped rather than enforced as an upper bound. A length larger than the bytes remaining in the message front makes ceph_decode_copy() read past the end of the front buffer. The message front is a dedicated allocation (ceph_msg_new2() -> kvmalloc), so the over-read runs off that object. A malicious or compromised MDS can trigger this with the first post-connect message on mount, with no client-side user interaction; under KASAN it is reported as a slab-out-of-bounds read in handle_session(). Impact: a malicious MDS can force the kernel client to read up to 4 GiB past the message front allocation during session setup, crashing the client (out-of-bounds read). Switch both copies to ceph_decode_copy_safe(), which performs the ceph_decode_need() bounds check before the copy and branches to the existing bad label, matching the rest of the decoder and the error path that frees the partially decoded cap_auths array. | 19 Oct |
| CVE-2026-89643 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: audit: avoid dropping live tree ref on fsnotify rule autoremove audit_del_rule() is used for both netlink deletion templates and internal fsnotify autoremove. The former passes a parsed template which owns a temporary tree reference; the latter passes the installed entry itself. The unconditional audit_put_tree() at the end of audit_del_rule() assumes the template case. For mixed AUDIT_DIR plus AUDIT_EXE rules, an fsnotify autoremove event therefore drops the installed rule's live tree reference. Repeating this across rules sharing the same tree can free the tree while another rule still references it, and a later autoremove dereferences the freed pathname while comparing rules. Move the temporary-tree put to audit_rule_change(), the caller that owns deletion templates. Keep it in the AUDIT_DEL_RULE cleanup so both successful deletion and -ENOENT still release the parser-owned tree. [PM: dropped unnecessary comment for line length reasons] | 19 Oct |
| CVE-2026-89637 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: smb: client: fix UAF and buffer leak in cifs_check_trans2() for malformed secondary T2 When a valid primary TRANSACT2 response has been received (mid->resp_buf set, mid->multiRsp true) and a subsequent secondary response causes cifs_check_trans2() to return false -- either because the SMB header is invalid (malformed != 0) or because check2ndT2() rejects the PDU -- handle_mid() overwrites mid->resp_buf with the new buffer (leaking the primary buffer) and, because mid->multiRsp is set, skips the server->smallbuf/bigbuf NULL-out. When the user thread frees mid->resp_buf, server->smallbuf or server->bigbuf is left dangling; the demux thread reuses it for the next packet, resulting in a use-after-free. Combine both early-exit conditions and, when mid->multiRsp is already set, abort the pending transaction inline: set multiEnd, call dequeue_mid() with malformed=true, and return true so handle_mid() exits without touching mid->resp_buf or the server buffer pointers. | 19 Oct |
| CVE-2026-89636 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: smb: client: clear ce->tgthint in free_tgts() When free_tgts() frees all structures in ce->tlist, ce->tgthint is left pointing to one of the freed cache_dfs_tgt structures. If ce->tgthint is not reset before it is used later, it results in a use-after-free. Set ce->tgthint to NULL in free_tgts() after the elements are freed to reflect that no elements remain. | 19 Oct |
| CVE-2026-89635 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: ksmbd: only rebind the reopened file's own oplock on durable reconnect ksmbd_reopen_durable_fd() walks the inode's m_op_list and rebinds every detached oplock to the reconnecting session: list_for_each_entry_rcu(op, &ci->m_op_list, op_entry, lockdep_is_held(&ci->m_lock)) { if (op->conn) continue; op->conn = ksmbd_conn_get(fp->conn); op->sess = work->sess; } The only key is op->conn == NULL, which every detached durable handle on that inode matches, not just the one owned by fp. When two sessions hold durable handles on the same file and both disconnect, reconnecting one of them adopts the other session's oplock: op->sess is overwritten with the reconnecting session without taking a reference on it, while op->conn pins the connection. The sibling teardown path, session_fd_check(), keys on the identity of the connection being torn down (op->conn == conn) rather than on shared state, and so does not have this problem. Once the adopting session is destroyed, ksmbd_session_destroy() frees it while the foreign oplock still points at it. The reader in ksmbd_close_fd_app_instance_id() validates only opinfo->conn, which is still live thanks to the reference taken above, and then dereferences the stale session: if (!opinfo->conn) { up_read(&fp->f_ci->m_lock); goto out; } ft = &opinfo->sess->file_table; write_lock(&ft->lock); BUG: KASAN: slab-use-after-free in _raw_write_lock+0x74/0xd0 Write of size 4 at addr ffff88810a970528 by task kworker/0:0/9 Workqueue: ksmbd-io handle_ksmbd_work Call Trace: _raw_write_lock+0x74/0xd0 ksmbd_close_fd_app_instance_id+0x183/0x410 smb2_open+0x1346/0x4430 handle_ksmbd_work+0x2bb/0x7b0 Reached from an authenticated session against a share with the default durable-handle and oplock configuration: two sessions open the same file with a durable-v2 handle and an RH lease under distinct AppInstanceIds, both log off, one reconnects with DH2C, and a later durable-v2 create carrying the other AppInstanceId walks into the freed session. Constrain the loop to the oplock owned by the file being reopened. | 19 Oct |
| CVE-2026-89614 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: ntfs: bound the free-cluster bitmap scan to the volume vol->lcn_empty_bits_per_page is sized from vol->nr_clusters at mount, but ntfs_cluster_alloc() bounds its scan of that array by the size of $Bitmap. Those are independent on-disk quantities and the mount-time check only rejects a $Bitmap that is too small, so an image whose $Bitmap covers more clusters than the volume has lets the scan index past the array. A run whose LCN lies in that gap takes the allocator straight there, since the caller passes the file's own last LCN as its locality hint. KASAN reports a slab out-of-bounds read when a file on such a volume is extended. Clamp the scan to what that array covers, mirroring the max_index calculation the mount-time scan already uses, and reject a decoded LCN at or beyond nr_clusters in the mapping pairs decoder. Conforming volumes are unaffected. | 19 Oct |
| CVE-2026-89613 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: ntfs: reject invalid empty mapping pairs Reject an attribute with empty mapping pairs if it has inconsistent highest VCN and size. | 19 Oct |
| CVE-2026-89612 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: ntfs: reject invalid MFT LCNs from boot sector The NTFS boot sector stores the MFT and MFTMirr locations as unsigned 64-bit LCNs, but parse_ntfs_boot_sector() decoded them into an s64. A crafted high-bit value could therefore become negative and pass the existing upper-bound check. The invalid value then propagated into the MFT zone allocator and could result in an out-of-bounds access to lcn_empty_bits_per_page. | 19 Oct |
| CVE-2026-89611 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: ntfs: validate non-resident attribute offsets ntfs_attr_update_meta() shifts the attribute name when converting between non-sparse and sparse attributes. Converting to sparse also adds the compressed_size field before the name and mapping pairs, requiring eight additional bytes in the attribute record. However, the validator does not check that name_offset is within safe boundaries for these operations or that the additional space is available. A malicious MFT record could set name_offset such that: 1. The name is positioned at the very end of a non-sparse attribute. Converting to sparse would shift the name forward by 8 bytes, writing beyond the attribute boundary. 2. The name overlaps with the mapping pairs, causing corruption during conversion. Add validation to ensure: - For named attributes, name_offset is within valid bounds - Name does not extend beyond the attribute or overlap with mapping pairs - For non-sparse, non-compressed attributes, eight bytes are available after mapping_pairs_offset for the compressed_size field The space check also covers unnamed attributes, for which name_offset = 0 is valid and no name range needs to be checked. | 19 Oct |
| CVE-2026-89610 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: ntfs: verify run length exceeding volume boundary The mapping pairs decoder validates that the starting LCN is within the volume but does not check if the run extends beyond the volume boundary. A malformed NTFS image with a crafted mapping pairs array could cause the kernel to access memory beyond the volume boundary, potentially leading to memory corruption and privilege escalation. Add validation to ensure lcn + length stays within nr_clusters. | 19 Oct |
| CVE-2026-89558 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: md/raid10: fix still_degraded being inverted in raid10_sync_request() Commit fe6a19d40ceb ("md/md-bitmap: merge md_bitmap_start_sync() into bitmap_operations") converted still_degraded from int to bool, but inverted the assignment in the loop that checks whether the array will still be degraded after the current device is recovered: "still_degraded = 1" became "still_degraded = false". As a result, recovering a device while another mirror is still missing calls md_bitmap_start_sync() with degraded == false, which clears bitmap bits that the still-missing device needs. When that device is re-added, its bitmap-based recovery finds the bits already cleared and skips every region written while the array was degraded, so it is marked In_sync while holding stale data: silent corruption. Reproducer (raid10 near=2, 4 disks, internal bitmap): - fail and remove one disk of each mirror pair - write to the degraded array - re-add both disks and let recovery finish - "check" reports mismatch_cnt=262272 after 256 MiB of degraded writes and file contents differ; the second disk's "recovery" completes in milliseconds because everything is skipped The same conversion in raid1 got it right (still_degraded = true). Restore the correct value. | 19 Oct |
| CVE-2026-89555 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: mpls: reload header after pskb_may_pull() mpls_select_multipath() calls mpls_multipath_hash() to choose a nexthop when an MPLS route has multiple nexthops. While walking the MPLS label stack, the hash routine caches hdr for the current label. After finding the bottom-of-stack label, it calls pskb_may_pull() before reading the inner IP header. If an skb is constructed with the inner IP header in nonlinear data and insufficient tailroom in the linear head, pskb_may_pull() calls pskb_expand_head() to replace the skb head and free the old one. This leaves hdr pointing to freed memory. The IPv6 path can invalidate hdr again when it performs a second pull for the larger header. The issue was found through static analysis. A reproducer sending a legal Geneve packet through a bareudp/MPLS multipath setup triggered the same KASAN report in 2 of 2 unpatched runs: BUG: KASAN: slab-use-after-free in mpls_select_multipath Read of size 1 at addr ffff88800ecc6e20 by task ksoftirqd/1/23 Call Trace: mpls_select_multipath mpls_forward __netif_receive_skb_list_core netif_receive_skb_list_internal napi_complete_done gro_cell_poll __napi_poll net_rx_action Freed by task 23: kfree pskb_expand_head __pskb_pull_tail mpls_select_multipath Reload hdr from the current skb head after each successful pull before deriving the inner IPv4 or IPv6 header pointer. | 19 Oct |
| CVE-2026-89551 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: SUNRPC: xdr_buf_trim: clamp buf->len to avoid underflow xdr_buf_trim() trims `len` bytes from the tail of an xdr_buf by walking the tail, pages, and head iovecs. Each per-section step uses min_t() so it never removes more bytes than that section holds, but the final accounting at the fix_len label subtracts the total bytes actually consumed from buf->len without any clamp: fix_len: buf->len -= (len - trim); When the caller has set buf->len to a value smaller than the sum of the iov_lens, (len - trim) can exceed buf->len and the unsigned subtraction wraps to near UINT_MAX. gss_krb5_unwrap_v2() reaches xdr_buf_trim() in exactly that state: buf->head[0].iov_len -= GSS_KRB5_TOK_HDR_LEN + headskip; buf->len = len - (GSS_KRB5_TOK_HDR_LEN + headskip); xdr_buf_trim(buf, ec + GSS_KRB5_TOK_HDR_LEN + tailskip); buf->len is a small wire-derived value while the iov_lens are at page scale, so the per-section loops legitimately consume far more bytes than buf->len records. The wrapped buf->len then propagates as the authoritative stream bound into every downstream XDR decoder. Fix by clamping the decrement so buf->len bottoms out at zero: buf->len -= min_t(unsigned int, buf->len, len - trim); On the normal path where the iov_lens sum to buf->len, (len - trim) is always <= buf->len and the result is identical to before. No callers change behavior outside the underflow case. | 19 Oct |
| CVE-2026-89546 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: SUNRPC: close backchannel before destroying callback service A backchannel receive can complete a request while the NFS callback service is being torn down. xprt_complete_bc_request() removes the request from bc_pa_list, drops bc_alloc_count, marks the request in use, and then asks xprt_enqueue_bc_request() to hand it to the callback service. If teardown has already cleared xprt->bc_serv, xprt_enqueue_bc_request() currently returns without enqueueing or freeing the committed request. The xprt_get() taken on entry is leaked as well. If the producer wins the race before bc_serv is cleared, it can also enqueue onto sv_cb_list after nfs_callback_down() has stopped the callback threads, leaving the request linked to a svc_serv that is about to be freed. Close the producer side before callback threads are stopped. Add xprt_svc_shutdown_bc() to clear xprt->bc_serv under bc_pa_lock, and call it on callback shutdown and callback-start failure before stopping the service threads. Requests that lose the NULL transition in xprt_enqueue_bc_request() are released through the normal backchannel free path after balancing bc_slot_count. Finally, drain any remaining sv_cb_list requests after the callback threads have stopped and before svc_destroy() frees the service. | 19 Oct |
| CVE-2026-89542 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: SUNRPC: harden gss_krb5_unwrap_v2 against short tokens gss_krb5_unwrap_v2() reads the EC and RRC header fields at ptr+4 and ptr+6 before validating that the token is at least GSS_KRB5_TOK_HDR_LEN (16) bytes long, and its rotate_left() helper passes buf->len - base to xdr_buf_subsegment() without verifying that base <= buf->len. When a caller hands in a sub-16-byte token, or a token whose declared len leaves base past the end of the buffer, three distinct failures follow: gss_krb5_unwrap_v2(offset, len, buf) ptr = buf->head[0].iov_base + offset ec = *(ptr + 4) /* OOB read on short head */ rrc = *(ptr + 6) /* OOB read on short head */ rotate_left(offset + 16, buf, rrc) xdr_buf_subsegment(buf, &subbuf, base, buf->len - base) /* u32 wrap when base > len */ _rotate_left(&subbuf, shift) shift %= buf->len /* divide-by-zero when base == len */ After decryption, the cleanup arithmetic has the same shape: movelen = min_t(unsigned int, buf->head[0].iov_len, len); movelen -= offset + GSS_KRB5_TOK_HDR_LEN + headskip; BUG_ON(offset + GSS_KRB5_TOK_HDR_LEN + headskip + movelen > buf->head[0].iov_len); The BUG_ON re-adds the value just subtracted, so it reduces to min(A, B) > A and is permanently false; it cannot catch the unsigned underflow of movelen, which then drives a ~UINT_MAX-byte memmove(). Add four defense-in-depth guards inside the unwrap core so it is safe regardless of what its callers validate: - reject tokens with len - offset < GSS_KRB5_TOK_HDR_LEN before touching ptr+4/ptr+6; - bail from rotate_left() when buf->len <= base, covering both the underflow and zero-length cases; - return early from _rotate_left() when buf->len is zero, so the shift %= buf->len modulo cannot fault; - replace the dead BUG_ON with a live check that returns GSS_S_DEFECTIVE_TOKEN before the movelen subtraction. | 19 Oct |
| CVE-2026-89541 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: SUNRPC: harden gss_unwrap_resp_priv length checks gss_unwrap_resp_priv() validates the RPCSEC_GSS opaque length with offset = (u8 *)(p) - (u8 *)head->iov_base; if (offset + opaque_len > rcv_buf->len) goto unwrap_failed; maj_stat = gss_unwrap(ctx->gc_gss_ctx, offset, offset + opaque_len, rcv_buf); Both operands are u32 and the sum is computed in u32. A reply with opaque_len near 0xffffffff makes offset + opaque_len wrap to a small value that is below rcv_buf->len, so the bound check passes and gss_unwrap() is called with end < begin. The check also lacks a lower bound, so any opaque_len in [0, GSS_KRB5_TOK_HDR_LEN) is accepted and forwarded to gss_krb5_unwrap_v2(), whose pre-decrypt header reads at ptr+4 and ptr+6 then run past the token. A krb5p NFS server returning a crafted RPCSEC_GSS reply can drive the client into out-of-bounds reads in gss_krb5_unwrap_v2() and the rotate_left() loop that follows. Fix by replacing the single combined check with three guards that are safe in u32 arithmetic and that enforce the RFC 4121 minimum outer token length: if (offset > rcv_buf->len) goto unwrap_failed; if (opaque_len > rcv_buf->len - offset) goto unwrap_failed; if (opaque_len < GSS_KRB5_TOK_HDR_LEN) goto unwrap_failed; The first guard makes the subtraction in the second guard unconditionally safe; offset is derived from a successful xdr_inline_decode() in the head kvec, so in practice it already satisfies the bound. The floor mirrors the server-side check added in commit 5b757c2e57a5 ("SUNRPC: svcauth_gss: enforce krb5 token minimum length"). | 19 Oct |
| CVE-2026-89538 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: SUNRPC: Reject krb5 v2 wrap tokens with oversized ec field gss_krb5_unwrap_v2() sets buf->len to a logical length, which can be much smaller than head[0].iov_len (the allocated receive-page capacity). It then calls xdr_buf_trim() with a trim length derived from the 16-bit "extra count" (ec) field in the Kerberos v2 token header. The ec field is authenticated by the post-decrypt memcmp() against the encrypted header copy, so a randomly-mutated value is rejected. However, any peer holding a valid GSS context can legitimately encrypt a token whose ec exceeds the plaintext length. Per RFC 4121, such a token is structurally malformed. Although xdr_buf_trim() now clamps the buf->len subtraction to avoid unsigned underflow, the buffer is still left in a semantically invalid state (zero length, inconsistent iov lengths) when ec is oversized. Reject these tokens before calling xdr_buf_trim(), giving callers a well-defined GSS_S_DEFECTIVE_TOKEN error and keeping the xdr_buf internally consistent. The wrapped blob begins at a nonzero offset -- both callers pass len as offset + opaque_len -- so buf->len still counts the offset bytes that precede the blob. Compare the trim length against the remaining wrapped segment, buf->len - offset, rather than the whole buffer; comparing against buf->len alone leaves an offset-wide window in which an oversized ec passes the test and xdr_buf_trim() cuts into the bytes ahead of the blob. | 19 Oct |
| CVE-2026-89536 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: SUNRPC: wait for in-flight client TLS handshake callback xs_tls_handshake_sync() gives xs_tls_handshake_done() a reference to the lower transport before submitting the handshake request. On timeout or signal, the synchronous waiter drops that reference after calling tls_handshake_cancel(). handshake_req_cancel() returns false when handshake_complete() has already marked the request complete. In that case the completion callback can still be running, so dropping the callback-owned reference in the waiter can free the lower transport before xs_tls_handshake_done() stores xprt_err or drops its own reference. If cancellation loses to completion, wait until xs_tls_handshake_done() signals handshake_done and let the callback release its reference. This mirrors the server-side handshake lifetime handling and keeps the timeout or signal return value unchanged. | 19 Oct |
| CVE-2026-89533 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: svcrdma: Fix offset arithmetic in read_chunk_range svc_rdma_read_chunk_range() walks a Read chunk's segment list to build a sub-range starting at byte offset and spanning length bytes for a Position-Zero or Call chunk. Two arithmetic defects in the per-segment loop produce wrong DMA lengths and a u32 underflow: pcl_for_each_segment(segment, chunk) { if (offset > segment->rs_length) { offset -= segment->rs_length; continue; } dummy.rs_handle = segment->rs_handle; dummy.rs_length = min_t(u32, length, segment->rs_length) - offset; dummy.rs_offset = segment->rs_offset + offset; First, the skip predicate uses '>' instead of '>='. When offset equals the segment's full rs_length, the segment is fully consumed and should be skipped, but the loop falls through into the body. The resulting dummy.rs_length is min_t(u32, length, rs_length) - rs_length, which underflows to a near-UINT_MAX u32 when length is smaller than rs_length, or is zero otherwise. Second, the length formula subtracts offset from the min_t() result rather than from segment->rs_length before the cap. For offset > 0 the segment's residual is rs_length - offset, not rs_length, so the cap must be applied to the residual. With the current bracketing, whenever length is smaller than rs_length - offset the per-segment length becomes length - offset instead of length, silently dropping offset bytes from the rebuilt chunk. Combined with the boundary case above it also enables the u32 underflow path, which propagates a huge nr_bvec into svc_rdma_build_read_segment() and a multi-MiB kmalloc_array_node() in svc_rdma_get_rw_ctxt(). Additionally, svc_rdma_read_call_chunk() can invoke this function with length == 0 when the last Read chunk ends exactly at the end of the Call chunk. With the corrected >= predicate, every segment is skipped and the function returns the initial -EINVAL, rejecting a valid request. Return success immediately when length is zero. Also break out of the loop once length is fully consumed to avoid passing zero-length segments to svc_rdma_build_read_segment(). Fix by using '>=' so a fully-consumed segment is skipped, by moving '- offset' inside min_t() so the cap is applied to the segment's residual length, by returning success for zero-length requests, and by stopping iteration when the requested range has been consumed. | 19 Oct |
| CVE-2026-89495 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: ocfs2: bound namelen in dlm_migrate_request_handler Patch series "ocfs2/dlm: bound peer-controlled lengths in the o2dlm". The o2dlm receive handlers trust u8 length and count fields from the wire without bounding them, so a node in a DLM domain can corrupt or panic any other node with a malformed message. Three defects: - dlm_migrate_request_handler() passes migrate->namelen unchecked to dlm_init_mle(), which memcpy()s it into the 32-byte mname[] of an o2dlm_mle slab object: a heap out-of-bounds write of up to ~215 attacker-controlled bytes. - dlm_mig_lockres_handler() passes mres->lockname_len unchecked to dlm_init_lockres(), which memcpy()s it into the 32-byte o2dlm_lockname slab object: a heap out-of-bounds write of up to ~223 bytes. - the same handler trusts mres->num_locks without checking that the message is large enough to hold that many entries, so dlm_process_recovery_data() walks mres->ml[] past the kmalloc(data_len) copy and trips a BUG_ON (an out-of-bounds read ending in a panic). The other o2dlm receive handlers already reject an oversized name; the migration and recovery handlers have omitted it since the DLM was added (see the Fixes tags). Patch 1 bounds namelen; patch 2 validates lockname_len, num_locks, and the payload size. Conforming recovery and migration traffic is unaffected. o2net authenticates peers only by the DLM domain key, so any node that has joined the domain -- including a compromised or malicious member -- can send these messages. There is no local trigger; the attacker must already be a member of the cluster. Each sink was confirmed under KASAN with an out-of-tree module mirroring it exactly -- a kmem_cache/kmalloc of the real destination size, then the same unclamped memcpy/loop: slab-out-of-bounds Write for the two writes, Read for the recovery walk, and a panic. A userspace AddressSanitizer build faults identically under -m32 and -m64. Scrubbed logs are available on request. I reported this privately to [email protected] and the ocfs2 maintainers on 2026-06-20; with no response after the standard embargo period I am posting the fix publicly. I have no embargo requirement. This patch (of 2): A node receiving a DLM_MIGRATE_REQUEST message trusts the peer-supplied name length (migrate->namelen) without bounding it. dlm_init_mle() then copies that many bytes into the fixed DLM_LOCKID_NAME_MAX-byte mname[] array of an o2dlm_mle slab object, so a malformed message from a cluster peer overflows the slab object by up to ~215 bytes: a heap out-of-bounds write of attacker-controlled data, reachable by any node in the domain. Reject an oversized name, the way dlm_master_request_handler() and the other o2dlm receive handlers already do; the migration handler omits the check entirely. Conforming messages are unaffected. | 19 Oct |
| CVE-2026-89494 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: ocfs2: validate lengths in dlm_mig_lockres_handler A node receiving a DLM_MIG_LOCKRES message trusts several fields of the peer-supplied dlm_migratable_lockres without validation. num_locks and lockname_len are bounded only on the sending side, and the message is never checked to actually carry num_locks migratable_lock entries. As a result dlm_process_recovery_data() walks mres->ml[0..num_locks) past the kmalloc(data_len) copy of the message (an out-of-bounds read that ends in a BUG_ON panic), and dlm_init_lockres() copies lockname_len bytes into the fixed 32-byte o2dlm_lockname slab object (a heap out-of-bounds write). Both are reachable by any node in the domain. Validate these fields right after dlm_grab(), before anything uses them -- including the not-joined error path, which already prints mres->lockname with the unbounded lockname_len as a %.*s precision. Reject the message unless lockname_len <= DLM_LOCKID_NAME_MAX, num_locks <= DLM_MAX_MIGRATABLE_LOCKS (the bound the sender already asserts), and the payload is large enough to hold the claimed locks. Conforming recovery and migration messages are unaffected. | 19 Oct |
| CVE-2026-89485 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: lockd: pin next file across nlm_inspect_file lock-drop nlm_traverse_files() pins the current file with f_count++ across a mutex_unlock for nlm_inspect_file(), but nothing pins the saved next pointer. A concurrent nlm_release_file() can kfree the next file during the unlock window, and the iterator dereferences freed memory on the next loop step. Pin both current and next before the lock-drop. Advance by swapping the pinned cursors at the end of each iteration so next is always held alive across the unlock. Always call nlm_file_release() after dropping the iteration pin, regardless of whether the file matched the predicate. Use nlm_file_inuse(), which does a live walk of the inode lock list, rather than the cached f_locks field, so skipped files that never ran nlm_inspect_file() are evaluated correctly. Because every file in a hash bucket is now pinned and released, files skipped by the is_failover_file predicate that have no locks, blocks, shares, or external references are deleted during traversal. The old code never evaluated skipped files for cleanup. The new behavior is intentional: such files are stale and should not persist in the table. | 19 Oct |
| CVE-2026-89482 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: nvme-tcp: do not accept C2HData based on blk_rq_payload_bytes() alone Commit 25e5cb780e62 ("nvme-tcp: fix possible crash in write_zeroes processing") established that blk_rq_payload_bytes() must not be read without first checking blk_rq_nr_phys_segments(), and recorded the result in nvme_tcp_setup_cmd_pdu() as req->data_len. The receive side was left as it was. The two differ for REQ_OP_WRITE_ZEROES, which has no physical segments but a non-zero blk_rq_bytes(), so setup leaves req->iter untouched while the receive gate lets a C2HData through and nvme_tcp_recv_data() copies into whatever the previous command on that tag left there. The driver-private area is zeroed only when the tag set is allocated. Reproduced with a test target that leaves a residual iterator on a tag and then sends a C2HData for a WRITE_ZEROES command on the same tag: BUG: KASAN: wild-memory-access in _copy_to_iter+0x642/0x1330 Write of size 512 at addr ffe728c2175dfa81 by task kworker/0:1H/103 CPU: 0 UID: 0 PID: 103 Comm: kworker/0:1H Not tainted 7.2.0-rc5-NVMETCP-gf5098b6bae76 #1 PREEMPT(lazy) Hardware name: QEMU Ubuntu 24.04 PC v2 (i440FX + PIIX, arch_caps fix, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 Workqueue: nvme_tcp_wq nvme_tcp_io_work Call Trace: <TASK> dump_stack_lvl+0x53/0x70 kasan_report+0xce/0x100 ? _copy_to_iter+0x642/0x1330 kasan_check_range+0x105/0x1b0 __asan_memcpy+0x3c/0x60 _copy_to_iter+0x642/0x1330 ? __pfx_sock_has_perm+0x10/0x10 ? worker_thread+0x45b/0xd10 ? __pfx__copy_to_iter+0x10/0x10 ? _raw_spin_lock_bh+0x83/0xe0 ? __pfx__raw_spin_lock_bh+0x10/0x10 __skb_datagram_iter+0xf3/0x820 ? __pfx_simple_copy_to_iter+0x10/0x10 ? __asan_memcpy+0x3c/0x60 ? skb_copy_bits+0x58d/0x830 skb_copy_datagram_iter+0x37/0x120 nvme_tcp_recv_skb+0xa07/0x4320 ? __pfx_nvme_tcp_recv_skb+0x10/0x10 __tcp_read_sock+0x1ab/0x810 ? __pfx_nvme_tcp_recv_skb+0x10/0x10 ? __pfx_lock_sock_nested+0x10/0x10 ? __pfx___tcp_read_sock+0x10/0x10 nvme_tcp_try_recv+0x152/0x1e0 ? __pfx_nvme_tcp_try_recv+0x10/0x10 ? __pfx_mutex_unlock+0x10/0x10 nvme_tcp_io_work+0x1e4/0x6c0 ? __schedule+0x181a/0x49f0 ? __pfx_nvme_tcp_io_work+0x10/0x10 process_one_work+0x633/0x1030 Keep the blk_rq_payload_bytes() test and add req->data_len to it. The old test is what rejects a C2HData naming a tag that is no longer in flight, because blk_update_request() zeroes rq->__data_len on completion; req->data_len and req->curr_bio are driver-private and survive completion, so they cannot stand in for it. Setup initialises the iterator only when both req->curr_bio and req->data_len are set, so the gate now tests the same two. | 19 Oct |
| CVE-2026-89479 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: sctp: stop processing a packet once its association is deleted sctp_endpoint_bh_rcv() looks the association up only when chunk->asoc is NULL, and caches the result in chunk->asoc and chunk->transport without taking a reference. A packet that matches no association is handed to the endpoint, so a peer can bundle COOKIE ECHO, SHUTDOWN and SHUTDOWN ACK in one packet. The COOKIE ECHO creates the association, the SHUTDOWN chunk caches it, and with the outqueue empty the SHUTDOWN ACK reaches sctp_sf_do_9_2_final(), so the association and its transports are freed. The endpoint loop has no counterpart to the asoc->base.dead check in sctp_assoc_bh_rcv(). The next chunk writes to last_time_heard in the freed transport and is then passed to sctp_do_sm() with the freed association. The transport is freed through RCU, so this needs the packet to come off the socket backlog, where the loop runs in task context. The endpoint loop cannot do the same check: it holds no reference on the association, so reading asoc->base.dead would itself be a use-after-free. Mark the packet for discard in the command interpreter, just before it deletes the association. That is also before sctp_inq_free() releases the chunk on the association receive path. sctp_sf_do_5_2_4_dupcook() issues SCTP_CMD_DELETE_TCB for the temporary association, while the one the packet belongs to stays alive. A restarting peer can bundle DATA behind its COOKIE ECHO, so compare against chunk->asoc and leave that case alone. | 19 Oct |
| CVE-2026-89478 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: sctp: drop a chunk if its transport was removed sctp_rcv() resolves the transport once per packet and leaves it in chunk->transport. The lookup reference, or the one sctp_add_backlog() takes if the socket is owned by userspace, keeps it around until the chunk has been processed. An authenticated ASCONF DEL-IP can remove it in the meantime. sctp_assoc_rm_peer() takes the transport out of the association and calls sctp_transport_free(), which tags it dead and drops the reference the association held. There is a window on both paths: the packet can sit on the socket backlog, and on the direct path the lookup completes before bh_lock_sock(). The DATA chunk in that packet puts the removed transport back into asoc->peer.last_data_from. Once the packet is done that reference goes away and the transport is freed by RCU, so the next delayed SACK carries the pointer into the SACK chunk and sctp_outq_select_transport() reads the freed transport's state. Drop the chunk in sctp_inq_push(), next to the existing rcvr->dead check. Both paths reach it with the association's socket lock held. The peer retransmits it. | 19 Oct |
| CVE-2026-81002 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: xdp: fix zero-copy frame layout xdp_convert_zc_to_xdp_frame() clones an XSK packet into an order-0 page and advertises PAGE_SIZE as its frame size. It allows the copied frame to occupy the page tail needed by skb_shared_info and records zero headroom even when metadata separates the frame header from packet data. An AF_XDP zero-copy packet redirected through cpumap can therefore make the skb overlap skb_shared_info or place it beyond the allocated page. Limit the copied layout to SKB_WITH_OVERHEAD(PAGE_SIZE) and include the metadata length in frame headroom. Redirect callers already handle a NULL conversion result. BUG: KASAN: slab-out-of-bounds in skb_gro_receive Write of size 4 at addr ffff88800cf37004 by task cpumap/1/map:1/146 Call Trace: skb_gro_receive (net/core/gro.c:174) udp_gro_receive (net/ipv4/udp_offload.c:812) inet_gro_receive (net/ipv4/af_inet.c:1539) dev_gro_receive (net/core/gro.c:515) gro_receive_skb (net/core/gro.c:633) cpu_map_kthread_run (kernel/bpf/cpumap.c:395) kthread (kernel/kthread.c:436) ret_from_fork (arch/x86/kernel/process.c:164) ret_from_fork_asm (arch/x86/entry/entry_64.S:255) Kernel panic - not syncing: KASAN: panic_on_warn set ... | 19 Oct |
| CVE-2026-80986 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: net/smc: bound the peer rkey counts in SMC-Rv2 LLC messages On a link whose device has max_recv_sge == 1 there is no shared v2 receive buffer, and smc_llc_save_add_link_rkeys() takes the v2 extension from 44 bytes past the start of the queue entry's inline message: ext = (struct smc_llc_msg_add_link_v2_ext *)(llc_msg + SMC_WR_TX_SIZE); The entry is a 72-byte allocation and the extension starts at offset 68, so ext->num_rkeys at offset 94 is already past it. This happens on every SMC-Rv2 link addition, whatever the peer sends: [ 2.490065] BUG: KASAN: slab-out-of-bounds in smc_llc_save_add_link_rkeys+0x333/0x350 [ 2.490431] Read of size 2 at addr ffff8880056406de by task smctest/106 [ 2.490709] [ 2.490792] CPU: 0 UID: 0 PID: 106 Comm: smctest Not tainted 7.2.0-rc5-p1-g77a5d9d9c99f #32 PREEMPT(lazy) [ 2.490795] Hardware name: QEMU Ubuntu 24.04 PC v2 (i440FX + PIIX, arch_caps fix, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 [ 2.490798] Call Trace: [ 2.490803] <TASK> [ 2.490805] dump_stack_lvl+0x53/0x70 [ 2.490810] print_report+0xd0/0x630 [ 2.490828] ? __pfx__raw_spin_lock_irqsave+0x10/0x10 [ 2.490832] ? smc_llc_save_add_link_rkeys+0x333/0x350 [ 2.490834] kasan_report+0xce/0x100 [ 2.490836] ? smc_llc_save_add_link_rkeys+0x333/0x350 [ 2.490837] smc_llc_save_add_link_rkeys+0x333/0x350 [ 2.490839] ? smcr_buf_map_lgr+0x1bf/0x2b0 [ 2.490844] smc_llc_cli_add_link+0xca7/0x1e80 [ 2.490848] ? smc_llc_wait+0x355/0x810 [ 2.490850] ? __pfx_smc_llc_wait+0x10/0x10 [ 2.490851] ? __pfx_smc_llc_cli_add_link+0x10/0x10 [ 2.490853] ? __pfx_autoremove_wake_function+0x10/0x10 [ 2.490863] __smc_connect+0x3f5c/0x4980 [ 2.490873] ? __pfx_kernel_connect+0x10/0x10 [ 2.490888] ? __pfx___smc_connect+0x10/0x10 [ 2.490891] ? release_sock+0x148/0x1d0 [ 2.490894] smc_connect+0x42c/0x580 [ 2.490896] __sys_connect+0xfc/0x130 [ 2.490898] ? __pfx___sys_connect+0x10/0x10 [ 2.490900] ? handle_mm_fault+0x1a1/0x430 [ 2.490908] __x64_sys_connect+0x6d/0xb0 [ 2.490909] ? fpregs_assert_state_consistent+0x56/0xe0 [ 2.490917] do_syscall_64+0xf9/0x540 [ 2.490921] entry_SYSCALL_64_after_hwframe+0x77/0x7f [ 2.490924] RIP: 0033:0x421bb4 [ 2.490927] Code: ff f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa 80 3d ad 34 09 00 00 74 13 b8 2a 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 4c c3 0f 1f 00 55 48 89 e5 48 83 ec 10 89 55 [ 2.490929] RSP: 002b:00007ffd473b01a8 EFLAGS: 00000202 ORIG_RAX: 000000000000002a [ 2.490935] RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 0000000000421bb4 [ 2.490936] RDX: 0000000000000010 RSI: 00007ffd473b01d0 RDI: 0000000000000003 [ 2.490937] RBP: 0000000000003930 R08: 0000000000000004 R09: 0000000000000000 [ 2.490938] R10: 00007ffd473b0f98 R11: 0000000000000202 R12: 0000000000000006 [ 2.490939] R13: 00007ffd473b0f87 R14: 0000000000000003 R15: 00007ffd473b0f90 [ 2.490940] </TASK> [ 2.490941] [ 2.499545] Allocated by task 44: [ 2.499693] kasan_save_stack+0x33/0x60 [ 2.499860] kasan_save_track+0x14/0x30 [ 2.500026] __kasan_kmalloc+0x8f/0xa0 [ 2.500190] __kmalloc_cache_noprof+0x158/0x370 [ 2.500393] smc_llc_enqueue+0x72/0x560 [ 2.500559] smc_wr_rx_tasklet_fn+0x474/0xa80 [ 2.500747] tasklet_action_common+0x20f/0x8a0 [ 2.500945] handle_softirqs+0x18e/0x590 [ 2.501115] do_softirq+0x3b/0x60 [ 2.501266] __local_bh_enable_ip+0x61/0x70 [ 2.501446] __alloc_skb+0x732/0x890 [ 2.501604] rxe_init_packet+0x16b/0x4f0 [ 2.501783] prepare_ack_packet+0xb8/0x830 [ 2.501962] rxe_receiver+0x495/0x96e0 [ 2.502125] do_work+0x144/0x470 [ 2.502269] process_one_work+0x633/0x1030 [ 2.502450] worker_thread+0x45b/0xd10 [ 2.50261 ---truncated--- | 19 Oct |
| CVE-2026-80981 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: net/smc: fix use-after-free of the LLC qentry in smc_llc_srv_add_link() smc_llc_srv_add_link() keeps add_llc pointing into the queue entry: add_llc = &qentry->msg.add_link; smc_llc.c:1482 ... smc_llc_save_add_link_info(link_new, add_llc); smc_llc.c:1494 smc_llc_flow_qentry_del(&lgr->llc_flow_lcl); smc_llc.c:1495 ... u8 *llc_msg = smc_link_shared_v2_rxbuf(link) ? (u8 *)lgr->wr_rx_buf_v2 : (u8 *)add_llc; smc_llc.c:1504 smc_llc_save_add_link_rkeys(link, link_new, llc_msg); smc_llc.c:1506 smc_llc_flow_qentry_del() kfree()s the entry, so on a link without a shared v2 receive buffer the pointer handed to smc_llc_save_add_link_rkeys() is already freed. Before the Fixes: commit that branch always used lgr->wr_rx_buf_v2 and add_llc was not used after the free. Reproduced on an unpatched tree over rxe, with KASAN, kasan_multi_shot and a link forced to max_recv_sge == 1: the entry is freed and read by the same call, and the freeing frame is smc_llc_srv_add_link() itself. [ 2.523161] BUG: KASAN: slab-use-after-free in smc_llc_save_add_link_rkeys+0x333/0x350 [ 2.523499] Read of size 2 at addr ffff8880052194de by task kworker/0:1/11 [ 2.523789] [ 2.523862] CPU: 0 UID: 0 PID: 11 Comm: kworker/0:1 Not tainted 7.2.0-rc5-p0-g2c9dd296545d #35 PREEMPT(lazy) [ 2.523865] Hardware name: QEMU Ubuntu 24.04 PC v2 (i440FX + PIIX, arch_caps fix, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 [ 2.523866] Workqueue: smc_hs_wq smc_listen_work [ 2.523869] Call Trace: [ 2.523870] <TASK> [ 2.523871] dump_stack_lvl+0x53/0x70 [ 2.523872] print_report+0xd0/0x630 [ 2.523874] ? __pfx__raw_spin_lock_irqsave+0x10/0x10 [ 2.523876] ? smc_llc_save_add_link_rkeys+0x333/0x350 [ 2.523878] kasan_report+0xce/0x100 [ 2.523879] ? smc_llc_save_add_link_rkeys+0x333/0x350 [ 2.523881] smc_llc_save_add_link_rkeys+0x333/0x350 [ 2.523883] ? smcr_buf_reg_lgr+0x2a4/0x660 [ 2.523885] smc_llc_srv_add_link+0xaa2/0x1e50 [ 2.523888] ? _printk+0xba/0xf0 [ 2.523897] ? __pfx_smc_llc_srv_add_link+0x10/0x10 [ 2.523899] ? down_write+0xb0/0x130 [ 2.523903] ? __pfx_down_write+0x10/0x10 [ 2.523905] smc_listen_work+0x489e/0x4d00 [ 2.523907] ? kmem_cache_free+0x1c6/0x3a0 [ 2.523911] ? __pfx_smc_listen_work+0x10/0x10 [ 2.523913] ? release_sock+0x148/0x1d0 [ 2.523915] ? smc_tcp_listen_work+0xb4f/0xfc0 [ 2.523917] ? _raw_spin_lock_irq+0x80/0xe0 [ 2.523918] ? __pfx__raw_spin_lock_irq+0x10/0x10 [ 2.523920] process_one_work+0x633/0x1030 [ 2.523922] ? assign_work+0x11d/0x370 [ 2.523924] worker_thread+0x45b/0xd10 [ 2.523926] ? __pfx_worker_thread+0x10/0x10 [ 2.523928] ? __pfx_worker_thread+0x10/0x10 [ 2.523929] kthread+0x2c6/0x3b0 [ 2.523931] ? recalc_sigpending+0x15c/0x1e0 [ 2.523934] ? __pfx_kthread+0x10/0x10 [ 2.523935] ret_from_fork+0x36e/0x5a0 [ 2.523937] ? __pfx_ret_from_fork+0x10/0x10 [ 2.523938] ? __switch_to+0x572/0xdd0 [ 2.523943] ? __pfx_kthread+0x10/0x10 [ 2.523944] ret_from_fork_asm+0x1a/0x30 [ 2.523947] </TASK> [ 2.523948] [ 2.531253] Allocated by task 48: [ 2.531399] kasan_save_stack+0x33/0x60 [ 2.531570] kasan_save_track+0x14/0x30 [ 2.531737] __kasan_kmalloc+0x8f/0xa0 [ 2.531905] __kmalloc_cache_noprof+0x158/0x370 [ 2.532100] smc_llc_enqueue+0x72/0x560 [ 2.532268] smc_wr_rx_tasklet_fn+0x474/0xa80 [ 2.532491] tasklet_action_common+0x20f/0x8a0 [ 2.532714] handle_softirqs+0x18e/0x590 [ 2.532886] do_softirq+0x3b/0x60 [ 2.533036] __local_bh_enable_ip+0x61/0x70 [ 2.533221] __alloc_skb+0x732/0x890 [ 2.533384] rxe_init_packet+0x16b/0x4f0 [ 2.533567] prepare_ack_packet+0xb8/0x830 [ 2.533760] rxe_receiver+0x495/0x96e0 [ 2.533933] do_work+0x144/0x470 [ 2 ---truncated--- | 19 Oct |
| CVE-2026-80976 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: seg6: reset IP6CB after IPv6 decapsulation decap_and_validate() pulls the outer SRv6 headers and makes the inner packet the skb network header. The IPv6 control block still contains values collected while parsing the outer packet, including nhoff and extension-header flags. End.DX6 and End.DT6 route the inner IPv6 packet directly to the IPv6 input path. An unprivileged user can reach End.DT6 from a user and net namespace by installing a local SID and injecting an outer packet with Hop-by-Hop and Destination Options headers followed by an SRH and a minimal inner IPv6 packet. The outer extension headers leave a large nhoff in IP6CB. After decapsulation, ip6_protocol_deliver_rcu() uses that stale offset on the inner packet and reads beyond the skb head. KASAN reports: BUG: KASAN: slab-out-of-bounds in ip6_protocol_deliver_rcu ip6_protocol_deliver_rcu+0x1118/0x1450 ip6_input_finish+0x11b/0x240 seg6_local_input_core+0xed/0x2e0 lwtunnel_input+0x1e9/0x4e0 ipv6_rthdr_rcv+0x525f/0x6c50 ip6_protocol_deliver_rcu+0xcb7/0x1450 Before clearing IP6CB for an inner IPv6 packet, save its incoming interface index and L3 slave state. Restore both after the clear and set nhoff to the inner IPv6 base-header nexthdr field. Use IP6CB(skb)->iif rather than skb->skb_iif because VRF processing can replace skb_iif with the L3 master while IP6CB keeps the receiving interface. Preserve IP6SKB_L3SLAVE for the same reason. | 19 Oct |
| CVE-2025-40261 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: nvme: nvme-fc: Ensure ->ioerr_work is cancelled in nvme_fc_delete_ctrl() nvme_fc_delete_assocation() waits for pending I/O to complete before returning, and an error can cause ->ioerr_work to be queued after cancel_work_sync() had been called. Move the call to cancel_work_sync() to be after nvme_fc_delete_association() to ensure ->ioerr_work is not running when the nvme_fc_ctrl object is freed. Otherwise the following can occur: [ 1135.911754] list_del corruption, ff2d24c8093f31f8->next is NULL [ 1135.917705] ------------[ cut here ]------------ [ 1135.922336] kernel BUG at lib/list_debug.c:52! [ 1135.926784] Oops: invalid opcode: 0000 [#1] SMP NOPTI [ 1135.931851] CPU: 48 UID: 0 PID: 726 Comm: kworker/u449:23 Kdump: loaded Not tainted 6.12.0 #1 PREEMPT(voluntary) [ 1135.943490] Hardware name: Dell Inc. PowerEdge R660/0HGTK9, BIOS 2.5.4 01/16/2025 [ 1135.950969] Workqueue: 0x0 (nvme-wq) [ 1135.954673] RIP: 0010:__list_del_entry_valid_or_report.cold+0xf/0x6f [ 1135.961041] Code: c7 c7 98 68 72 94 e8 26 45 fe ff 0f 0b 48 c7 c7 70 68 72 94 e8 18 45 fe ff 0f 0b 48 89 fe 48 c7 c7 80 69 72 94 e8 07 45 fe ff <0f> 0b 48 89 d1 48 c7 c7 a0 6a 72 94 48 89 c2 e8 f3 44 fe ff 0f 0b [ 1135.979788] RSP: 0018:ff579b19482d3e50 EFLAGS: 00010046 [ 1135.985015] RAX: 0000000000000033 RBX: ff2d24c8093f31f0 RCX: 0000000000000000 [ 1135.992148] RDX: 0000000000000000 RSI: ff2d24d6bfa1d0c0 RDI: ff2d24d6bfa1d0c0 [ 1135.999278] RBP: ff2d24c8093f31f8 R08: 0000000000000000 R09: ffffffff951e2b08 [ 1136.006413] R10: ffffffff95122ac8 R11: 0000000000000003 R12: ff2d24c78697c100 [ 1136.013546] R13: fffffffffffffff8 R14: 0000000000000000 R15: ff2d24c78697c0c0 [ 1136.020677] FS: 0000000000000000(0000) GS:ff2d24d6bfa00000(0000) knlGS:0000000000000000 [ 1136.028765] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 1136.034510] CR2: 00007fd207f90b80 CR3: 000000163ea22003 CR4: 0000000000f73ef0 [ 1136.041641] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 1136.048776] DR3: 0000000000000000 DR6: 00000000fffe07f0 DR7: 0000000000000400 [ 1136.055910] PKRU: 55555554 [ 1136.058623] Call Trace: [ 1136.061074] <TASK> [ 1136.063179] ? show_trace_log_lvl+0x1b0/0x2f0 [ 1136.067540] ? show_trace_log_lvl+0x1b0/0x2f0 [ 1136.071898] ? move_linked_works+0x4a/0xa0 [ 1136.075998] ? __list_del_entry_valid_or_report.cold+0xf/0x6f [ 1136.081744] ? __die_body.cold+0x8/0x12 [ 1136.085584] ? die+0x2e/0x50 [ 1136.088469] ? do_trap+0xca/0x110 [ 1136.091789] ? do_error_trap+0x65/0x80 [ 1136.095543] ? __list_del_entry_valid_or_report.cold+0xf/0x6f [ 1136.101289] ? exc_invalid_op+0x50/0x70 [ 1136.105127] ? __list_del_entry_valid_or_report.cold+0xf/0x6f [ 1136.110874] ? asm_exc_invalid_op+0x1a/0x20 [ 1136.115059] ? __list_del_entry_valid_or_report.cold+0xf/0x6f [ 1136.120806] move_linked_works+0x4a/0xa0 [ 1136.124733] worker_thread+0x216/0x3a0 [ 1136.128485] ? __pfx_worker_thread+0x10/0x10 [ 1136.132758] kthread+0xfa/0x240 [ 1136.135904] ? __pfx_kthread+0x10/0x10 [ 1136.139657] ret_from_fork+0x31/0x50 [ 1136.143236] ? __pfx_kthread+0x10/0x10 [ 1136.146988] ret_from_fork_asm+0x1a/0x30 [ 1136.150915] </TASK> | 18 Oct |
| CVE-2026-80681 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: vxlan: re-fetch eth header after route_shortcircuit() Before route_shortcircuit(), the eth header pointer is cached from eth_hdr(skb). Inside route_shortcircuit(), pskb_may_pull() can be called, which may reallocate skb->head. In this case, returning to vxlan_xmit() leaves the cached eth pointer pointing to freed memory, leading to a use-after-free when dereferencing eth->h_dest. Fix this by updating eth = eth_hdr(skb) after calling route_shortcircuit(). | 16 Oct |
| CVE-2026-80630 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: net/sched: sch_fq_codel: Do not call qdisc_tree_reduce_backlog during peek before restoring qlen Whenever fq_codel drops packets during peek, it calls qdisc_tree_reduce_backlog. An issue arises because it calls qdisc_tree_reduce_backlog before it reincrements the qlen. If qlen drops to zero, but peek returns an skb, the parent's qlen_notify callback will be executed even though fq_codel still has 1 packet on the queue and, thus, will mistakenly deactivate the parent's class causing issues like a recent report [1] and a wild memory access in qfq: [ 29.371146][ T360] Oops: general protection fault, probably for non-canonical address 0xfbd59c0000000024: 0000 [#1] SMP KASAN NOPTI [ 29.371666][ T360] KASAN: maybe wild-memory-access in range [0xdead000000000120-0xdead000000000127] [ 29.371987][ T360] CPU: 6 UID: 0 PID: 360 Comm: tc Not tainted 7.1.0-rc5-00285-gc530e5b2dbc6-dirty #82 PREEMPT(full) [ 29.372384][ T360] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011 [ 29.372620][ T360] RIP: 0010:qfq_deactivate_agg (include/linux/list.h:1029 (discriminator 2) include/linux/list.h:1043 (discriminator 2) net/sched/sch_qfq.c:1369 (discriminator 2) net/sched/sch_qfq.c:1395 (discriminator 2)) sch_qfq [ 29.373544][ T360] RSP: 0018:ffff888102417370 EFLAGS: 00010216 [ 29.373800][ T360] RAX: 0000000000000000 RBX: ffff88811224d568 RCX: dffffc0000000000 [ 29.374079][ T360] RDX: 1ffff11021fe1543 RSI: ffff88810ff0aa00 RDI: dffffc0000000000 [ 29.374368][ T360] RBP: ffff88811224c280 R08: dead000000000122 R09: 1bd5a00000000024 [ 29.374649][ T360] R10: fffffbfff7940329 R11: fffffbfff7940329 R12: 0000000000000000 [ 29.374926][ T360] R13: dead000000000100 R14: ffff88811224d580 R15: ffff88811224d578 [ 29.375207][ T360] FS: 00007f5b794e5780(0000) GS:ffff88815d1e9000(0000) knlGS:0000000000000000 [ 29.375545][ T360] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 29.375823][ T360] CR2: 000055ffb091f000 CR3: 000000010a305000 CR4: 0000000000750ef0 [ 29.376103][ T360] PKRU: 55555554 [ 29.376258][ T360] Call Trace: [ 29.376401][ T360] <TASK> ... [ 29.376885][ T360] qfq_reset_qdisc (net/sched/sch_qfq.c:357 net/sched/sch_qfq.c:1487) sch_qfq [ 29.377074][ T360] qdisc_reset (net/sched/sch_generic.c:1057) [ 29.377414][ T360] __qdisc_destroy (net/sched/sch_generic.c:1096) [ 29.377600][ T360] qdisc_graft (net/sched/sch_api.c:1062 net/sched/sch_api.c:1053 net/sched/sch_api.c:1159) [ 29.378593][ T360] tc_get_qdisc (net/sched/sch_api.c:1528 net/sched/sch_api.c:1556) Fix this by only calling qdisc_tree_reduce_backlog in peek after the qlen is restored. [1] http://lore.kernel.org/netdev/CAN2cbVe79oj0O9==m4+4x3v+O+qzRagA=2=wkrp9i9=CqYvyZA@mail.gmail.com/ | 16 Oct |
| CVE-2026-80609 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: qede: fix out-of-bounds check for cqe->len_list[] Move index check before element access. | 16 Oct |
| CVE-2026-80561 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: libceph: fix multiple unsafe decodes in decode_locker() decode_locker() in cls_lock_client.c contains three unsafe decode operations that allow a malicious or compromised OSD to trigger slab-out-of-bounds reads: 1. ceph_decode_copy() at the locker_id_t name field has no preceding bounds check. With p == end after ceph_start_decoding() accepts struct_len=0, this reads sizeof(ceph_entity_name) = 9 bytes past the validated buffer boundary. 2. *p += sizeof(struct ceph_timespec) after the locker_info_t header is an unchecked pointer advance. A malicious OSD can position p past end, causing all subsequent _safe checks to pass against a bogus boundary. 3. len = ceph_decode_32(p) has no preceding bounds check, and the immediately following *p += len is uncapped. A malicious OSD can send len=0xffffffff, advancing p gigabytes past end and escaping the decode window entirely. Fix all three by replacing bare operations with their safe variants: ceph_decode_copy -> ceph_decode_copy_safe *p += sizeof(...) -> ceph_decode_skip_n ceph_decode_32(p) -> ceph_decode_32_safe *p += len -> ceph_decode_skip_n A new label is added to return -EINVAL on any bounds violation. -EINVAL is appropriate here: the data received from the OSD is structurally malformed, which is an invalid argument to the decode contract regardless of whether the caller or the wire is at fault. Attacker model: a malicious or compromised OSD in a multi-tenant Ceph deployment can trigger this against any kernel client that issues the lock.get_info class method (e.g. during RBD exclusive lock acquisition) without any further privileges beyond OSD session establishment. [ idryomov: use ceph_decode_skip_string() to skip description, trim changelog ] | 16 Oct |
| CVE-2026-80558 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: libceph: Avoid using invalid osd indices from primary_temp A corrupted osdmap received from a Ceph monitor or OSD may contain osd indices in its pg_temp, primary_temp, pg_upmap, and pg_upmap_items parts that don't exist, i.e., that are greater than max_osd or smaller than CEPH_HOMELESS_OSD (-1). These indices are used to create the up and acting set in ceph_pg_to_up_acting_osds(), called from calc_target(). While most of these osd indices are checked, the one from primary_temp is not. Subsequently, this may lead to calc_target() returning this (potentially invalid) index as target osd for a (linger) request. Because the osd_state, osd_weight, and osd_addr arrays only contain max_osd entries (with indices 0 to max_osd -1), this leads to out-of-bounds accesses when trying to read values from these arrays. This patch fixes the issue by adding a check to get_temp_osds(), so that only valid osd indices from primary_temp are used, and it falls back to using the primary from pg_temp or the up set if it is invalid. [ idryomov: changelog ] | 16 Oct |
| CVE-2026-80557 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: libceph: fix OOB read in decode_watchers() via missing bounds check ceph_start_decoding() validates that struct_len bytes remain in the buffer after the encoding header, but accepts struct_len=0 as valid: ceph_decode_need(p, end, 0, bad) always passes. When a malicious or compromised OSD sends an obj_list_watch_response_t reply with struct_len=0, ceph_start_decoding() returns success with p == end, leaving zero bytes guaranteed for subsequent reads. The immediately following ceph_decode_32(p) in decode_watchers() has no preceding bounds check. With p == end this is a 4-byte read past the validated buffer boundary. The garbage value is then passed directly to kzalloc_objs() as the watcher count. The sibling function decode_watcher() already uses the safe variants (ceph_decode_copy_safe, ceph_decode_64_safe, ceph_decode_skip_32) after its own ceph_start_decoding() call. decode_watchers() is the only site that uses the bare variant, confirming an oversight. Fix by replacing ceph_decode_32(p) with ceph_decode_32_safe(p, end, *num_watchers, bad), consistent with the established pattern. Attacker model: a malicious or compromised OSD in a multi-tenant Ceph deployment (e.g. cloud) can trigger this against any kernel client that calls CEPH_OSD_OP_LIST_WATCHERS, without any further privileges beyond OSD session establishment. [ idryomov: trim changelog ] | 16 Oct |
| CVE-2026-80528 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: ceph: avoid fs reclaim while using current->journal_info handle_reply() stores a `ceph_mds_request` pointer in `current->journal_info` while filling the inode and dentry cache from an MDS reply. An allocation in this section can enter direct reclaim and prune dentries from another filesystem. If this dirties an ext4 inode, ext4 starts a JBD2 transaction. JBD2 interprets the Ceph request in `current->journal_info` as a journal handle and dereferences the request's `r_tid` as `h_transaction`, causing a kernel crash, e.g.: Unable to handle kernel paging request at virtual address 00000000077b4818 [...] Internal error: Oops: 0000000096000004 [#1] SMP Modules linked in: CPU: 6 UID: 0 PID: 2699135 Comm: kworker/6:3 Tainted: G W 6.18.38-i3 #1113 NONE [...] Workqueue: ceph-msgr ceph_con_workfn pstate: 80400009 (Nzcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : jbd2__journal_start+0x2c/0x208 lr : __ext4_journal_start_sb+0x100/0x178 [...] Call trace: jbd2__journal_start+0x2c/0x208 (P) __ext4_journal_start_sb+0x100/0x178 ext4_dirty_inode+0x3c/0x90 __mark_inode_dirty+0x58/0x400 iput.part.0+0x2b0/0x370 iput+0x18/0x30 dentry_unlink_inode+0xc0/0x158 __dentry_kill+0x80/0x250 shrink_dentry_list+0x90/0x130 prune_dcache_sb+0x60/0x98 super_cache_scan+0xe8/0x190 do_shrink_slab+0x174/0x388 shrink_slab+0xd8/0x4c0 shrink_node+0x31c/0x908 do_try_to_free_pages+0xd0/0x508 try_to_free_pages+0x11c/0x238 __alloc_frozen_pages_noprof+0x4d0/0xdd0 __folio_alloc_noprof+0x18/0x70 __filemap_get_folio+0x248/0x440 ceph_readdir_prepopulate+0x570/0x9e8 mds_dispatch+0x1424/0x1ba0 ceph_con_process_message+0x74/0xa0 ceph_con_v1_try_read+0x3a0/0x1510 ceph_con_workfn+0x260/0x460 Enter a scoped NOFS allocation context and leave it after clearing `journal_info`. This prevents filesystem reclaim from recursing into another filesystem while the field contains Ceph-private data. | 16 Oct |
| CVE-2026-74746 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: netfilter: flowtable: publish GC-visible tuple last nf_flow_table_iterate() only treats original-direction tuple nodes as owning entries. Publishing the original node first lets GC observe and free a flow while flow_offload_add() is still inserting the reply node. Publish the reply node first and the original node last so GC never sees a partially installed flow. KASAN can trigger slab-use-after-free read and write reports in the flowtable/rhashtable path (rht_deferred_worker, jhash, flow_offload_del, flow_offload_lookup, etc.). | 16 Oct |
| CVE-2026-74744 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: ipvlan: inherit needed_headroom and needed_tailroom from phy_dev ipvlan devices inherit hard_header_len from phy_dev during ipvlan_init(), but leave needed_headroom and needed_tailroom set to 0. When the underlying phy_dev (or stacked lower device) requires extra headroom or tailroom for headers/trailers (e.g. macsec, ipsec, wireguard, tunnels, or veth with rx headroom), upper layers calculating packet headroom and tailroom fail to reserve sufficient space. This can result in reallocation overhead, skb headroom underflows, or KASAN slab-use-after-free crashes when dev_hard_header() / ipvlan_hard_header() prepends header data or when lower devices append tailroom. Fix this by: 1. Inheriting needed_headroom and needed_tailroom from phy_dev in ipvlan_init(). 2. Propagating needed_headroom and needed_tailroom updates to attached ipvlans in ipvlan_device_event() when receiving NETDEV_FEAT_CHANGE events. | 16 Oct |
| CVE-2026-74743 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: macvlan: inherit needed_headroom and needed_tailroom from lowerdev macvlan devices inherit hard_header_len from lowerdev during macvlan_init(), but leave needed_headroom and needed_tailroom set to 0. When the underlying lowerdev requires extra headroom or tailroom for headers/trailers (e.g. macsec, ipsec, wireguard, tunnels, or veth with rx headroom), upper layers calculating packet headroom and tailroom fail to reserve sufficient space. This can result in reallocation overhead, skb headroom underflows, or KASAN slab-use-after-free crashes when dev_hard_header() / macvlan_hard_header() prepends header data or when lower devices append tailroom. Fix this by: 1. Inheriting needed_headroom and needed_tailroom from lowerdev in macvlan_init(). 2. Propagating needed_headroom and needed_tailroom updates to attached macvlans in macvlan_device_event() when receiving NETDEV_FEAT_CHANGE events. | 16 Oct |
| CVE-2026-74730 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: NFS: Pin the 'struct nfs_server' during a FREE_STATEID call Dan Aloni reports that he was able to hit a use-after-free bug if a FREE_STATEID operation gets delayed for whatever reason. Fix this by bumping the refcount of the 'struct nfs_server' object for the duration of the FREE_STATEID so it doesn't get cleaned up from underneath us while operations are still in flight. | 16 Oct |
| CVE-2026-74688 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: sctp: clear control chunk transport if it is being removed sctp_make_heartbeat_ack() caches the destination transport in chunk->transport without taking a reference. When src_out_of_asoc_ok is enabled, the HEARTBEAT ACK may remain queued on control_chunk_list instead of being transmitted immediately. If the peer transport is removed while the chunk is still queued, sctp_assoc_rm_peer() drops the transport and schedules it for RCU freeing, but only clears cached transport pointers in out_chunk_list. The queued control chunk therefore retains a dangling transport pointer. Once an ASCONF_ACK clears the suppression and the queued control chunk is transmitted, SCTP dereferences the stale transport pointer, leading to a use-after-free. Fix this by also clearing chunk->transport for queued control chunks in control_chunk_list when removing the transport. | 16 Oct |
| CVE-2026-74669 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: ipvs: clear IPv4 options after rebasing tunnel ICMP errors ip_vs_in_icmp() rebases an skb from the outer ICMP packet to the quoted original request before passing it to icmp_send(). However, IPCB(skb)->opt still describes the outer IPv4 header. A timestamp option in the outer header can therefore leave an offset that points into the quoted transport header after the rebase. __ip_options_echo() treats a byte at that stale location as the option length and copies it into the fixed-size option storage on the __icmp_send() stack, causing a stack out-of-bounds write. Clear the stale option metadata after resetting the network header. Keep the remaining control block fields, including the ingress interface used by the ICMP response path. | 16 Oct |
| CVE-2026-74662 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: inet: frags: publish queues before arming timer inet_frag_create() arms the fragment queue timer before inserting the queue into the fqdir rhashtable. If the namespace fragment timeout is zero or negative, the timer can run before the queue is published. The timer callback then marks the queue complete, tries to remove a node that is not in the hash table yet, and drops the anticipated hash reference. Creation can subsequently publish the completed queue without restoring that reference, leaving a stale hash node after the caller drops the remaining reference. Publish the queue first and arm the timer while holding the queue lock. This makes timer expiry wait until the queue is visible in the hash table, so inet_frag_kill() can remove the node and balance the hash reference. | 16 Oct |
| CVE-2026-74617 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: dibs: initialise dibs->lock in dibs_dev_alloc() dibs->lock is initialised by dibs_dev_add(), but a dibs device can already take interrupts before that call: ism_probe() runs ism_dev_init(), and hence request_irq(), before it calls dibs_dev_add(). No client can have registered a dmb at that point, so no dmb interrupt can occur, but a GID event interrupt can, and ism_handle_irq() takes dibs->lock unconditionally on entry, before it inspects anything else. Initialise the lock in dibs_dev_alloc() instead, so that it is valid as soon as a driver can publish the device to its interrupt handler. | 16 Oct |
| CVE-2026-74616 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: xdp: reject clones that overrun skb_shared_info tailroom xdpf_clone() clones broadcast copies into a single page and sets frame_sz to PAGE_SIZE. __xdp_build_skb_from_frame() later treats that page like a normal XDP frame and expects the usual skb_shared_info tailroom at the end of the buffer. The current check only rejects frames whose linear xdp_frame header, headroom, and packet data exceed PAGE_SIZE. A source frame backed by a larger allocation can still satisfy that check while extending into the clone's required shared-info area. When such a clone is converted back into an skb, build_skb_around() places skb_shared_info over live packet bytes and later writes can corrupt XDP return metadata. Reject clones unless their linear area fits inside SKB_WITH_OVERHEAD(PAGE_SIZE), matching the tailroom requirement already enforced by the XDP-to-skb conversion path. | 16 Oct |
| CVE-2026-74597 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: ip6_tunnel: clear skb2->cb[] in ip6ip6_err() ip6ip6_err() clones an outer IPv6 ICMP error skb, pulls it to the quoted inner IPv6 packet, and then passes the clone to icmpv6_send(). The clone still carries the outer packet's inet6_skb_parm in skb->cb. If the outer packet had a Home Address Option, IP6CB(skb2)->dsthao remains non-zero after skb_pull(). icmpv6_send() later calls mip6_addr_swap(), which uses that stale dsthao offset against the quoted inner packet. A malformed inner destination-options header can then make the HAO lookup and address swap run past the end of the quoted packet and corrupt skb_shared_info. Clear skb2->cb[] before pulling the quoted inner IPv6 packet so the reply path does not reuse metadata left by the outer IPv6 stack. | 16 Oct |
| CVE-2026-74588 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: sctp: keep chunk->transport in step with the list it is queued on __sctp_outq_flush_rtx() moves a gap-acked chunk onto another transport's transmitted list without updating chunk->transport: if (chunk->tsn_gap_acked) { list_move_tail(&chunk->transmitted_list, &transport->transmitted); continue; } The chunk then sits on a live transport's list while chunk->transport still names a different one. If that transport is removed - sctp_assoc_rm_peer() from an ASCONF Delete-IP - sctp_transport_free() RCU-frees it and the chunk is left with a dangling pointer. sctp_assoc_rm_peer() scrubs peer->transmitted and asoc->outqueue.out_chunk_list, but the chunk is on neither. The pointer is not followed while tsn_gap_acked is set. A SACK that reneges on the TSN clears the flag, and the next SACK reaches tchunk->transport->flight_size -= sctp_data_size(tchunk); inside the freed transport. KASAN reports a slab-use-after-free read in sctp_check_transmitted(), freed from sctp_assoc_rm_peer(). Both the removal and the SACKs come from the association peer. Set chunk->transport at the move. The ordinary resend path needs nothing: it reaches its list_move_tail() only after sctp_packet_append_chunk() returned SCTP_XMIT_OK, and __sctp_packet_append_chunk() has rebound the chunk by then. Discovered by XBOW, triaged by Baul Lee <[email protected]> | 16 Oct |
Download these 474 as CSV · subscribe to this list.
EPSS scores: 2026-10-29. NVD cursor: 2026-10-29 00:22. The News page shows only notable CVEs (KEV, your stack, new criticals, EPSS over 50%, or active exploitation per SSVC); this table has all of them.