Vulnerabilities
All
My stack
Known exploited
Public exploit
Critical (9+)
Likely exploited (EPSS ≥ 50%)
Changed, 24 h
New, 24 h
Sort:
risk
modified
published
CVSS
EPSS
| CVE | CVSS | EPSS | Vendor, product | Description | Modified |
|---|---|---|---|---|---|
| CVE-2026-98526 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: llc: reserve device headroom for allocated frames llc_alloc_frame() reserves link-layer headroom using the device type. This is insufficient for stacked Ethernet devices such as VLAN devices, where vlan_dev_hard_header() pushes a VLAN header before the lower device's Ethernet header. An LLC response on such a device can therefore underflow skb headroom in eth_header(). Use LL_RESERVED_SPACE() to account for the device's actual required headroom while preserving the existing LLC device-type check. | 19 Oct |
| CVE-2026-98481 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: nfc: port100: reject frames whose declared length exceeds the received data port100_recv_response() passes the URB transfer buffer to port100_rx_frame_is_valid(), which checksums le16_to_cpu(frame->datalen) bytes of frame->data. datalen is a 16-bit field supplied by the device and is never checked against the number of bytes actually received (urb->actual_length), so a device reporting a datalen larger than the received frame makes port100_data_checksum() read out of bounds past the transfer buffer. Reject a response whose declared frame size does not fit the received length before validating it. Found by 0sec (https://0sec.ai) using automated source analysis; the missing bound is evident from source. Compile-tested. | 19 Oct |
| CVE-2026-98461 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: Bluetooth: hci_sock: validate event length before filtering is_filtered_packet() reads the event code from skb->data[0] without first checking that the skb is nonempty. When an opcode filter is configured, it also reads the command opcode at offsets 3 or 4 without checking that a Command Complete or Command Status event is long enough. hci_send_to_sock() invokes the filter before hci_event_packet() validates the event header. A malformed event supplied by a controller or a vhci device can therefore cause an out-of-bounds read. Keep the unmasked event code for the opcode checks. The masked value is needed for the 64-bit event bitmap, but using it to identify command events aliases event codes above 0x3f. In particular, Synchronous Train Complete (0x4f) was treated as Command Status (0x0f) even though its payload has no opcode. Reject actual command events that are too short for the field being inspected. A truncated command event cannot match a configured opcode. | 19 Oct |
| CVE-2026-98435 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: EDAC/altera: Use parent device for devres in altr_portb_setup() Anchor the devres group and the devm-managed IRQ requests in altr_portb_setup() to the actual parent device (device->edac->dev) instead of the embedded struct device inside the copied per-port altr_edac_device_dev. This keeps devres_open_group(), devm_request_irq(), devres_remove_group() and devres_release_group() all referring to the same long-lived device so the group and the resources allocated inside it are torn down together. | 19 Oct |
| CVE-2026-98400 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: s390/ipl: Fix NULL deref in kdump without re-IPL parm block Some IPL types, like HMC FTP boot or QEMU direct kernel boot, might not provide an IPL parameter block. In this case, reipl_type_init() selects IPL_TYPE_UNKNOWN, and reipl_block_actual remains NULL. kdump passes the re-IPL parameter block to the dump kernel through os_info. Before commit 3b9678472bab ("s390/ipl: correct kdump reipl block checksum calculation"), the os_info entry was added only for IPL types which initialized reipl_block_actual. That commit moved the os_info update to machine_crash_shutdown(), making it unconditional. As a result, set_os_info_reipl_block() dereferences reipl_block_actual for IPL_TYPE_UNKNOWN. This may happen to work by chance when address zero contains readable lowcore data and the resulting empty os_info entry is ignored by the dump kernel. Skip the os_info update when no re-IPL parameter block is available. Kdump then collect the dump and reboot without setting re-IPL parameter block. | 19 Oct |
| CVE-2026-98399 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: s390/ipl: Fix NULL deref in dump_reipl without re-IPL parm block Unlike kdump, which passes the re-IPL parameter block through os_info, the stand-alone dump passes it through the IPL parm block address and checksum in lowcore. Some IPL types, like HMC FTP boot or QEMU direct kernel boot, might not provide an IPL parameter block. In this case reipl_type_init() selects IPL_TYPE_UNKNOWN and reipl_block_actual remains NULL. Nevertheless, dump_reipl_run() unconditionally dereferences it when preparing the lowcore fields. This may happen to work by chance when address zero contains readable lowcore data. A zero IPL parameter block address is then stored in lowcore, causing the stand-alone dumper to enter disabled wait after completing the dump. Explicitly store a zero IPL parameter block address and checksum when no re-IPL parameter block is available. This does not change the behavior: the stand-alone dumper completes the dump and halts, while valid re-IPL parameter blocks continue to be handled as before. | 19 Oct |
| CVE-2026-98329 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: wifi: mac80211: don't allow injecting frames wider than the chanctx Frames injected on a monitor interface can carry a radiotap field requesting a bandwidth, which mac80211 passes down to the driver regardless of the the actual operational bandwidth. If the bandwidth requested is too wide, that triggers a warning in hwsim: WARN_ON(hwsim_get_chanwidth(bw) > hwsim_get_chanwidth(confbw)) Drop such frames entirely instead since they cannot be sent. | 19 Oct |
| CVE-2026-98312 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: ALSA: 6fire: fix OOB write from device-reported iso length usb6fire_pcm_in_urb_handler() sizes each outgoing isochronous packet as (actual_length - 4) / (in_n_analog << 2) * (out_n_analog << 2) + 4, where actual_length is the unsigned length the device reported for the matching IN packet. A packet completed with status 0 and actual_length < 4 wraps the subtraction to 0x7fffffec; a zero-length isochronous packet is legal on the bus, and the preceding loop rejects only non-zero status. The sum reaches memset() on out_urb->buffer, a 4832-byte object from kcalloc(PCM_MAX_PACKET_SIZE, PCM_N_PACKETS_PER_URB). Even without the wrap the result is out of bounds: at 88.2/96 kHz the 4-in/6-out scaling turns a full 420-byte IN packet into 628, so eight packets span 5024 bytes of that buffer. usb_submit_urb() rejects an over-long descriptor only after the memset() and the usb6fire_pcm_playback() copy of user PCM data have run. Guard the subtraction as the sibling usb6fire_pcm_capture() already does, and limit the frame count to what fits in rt->out_packet_size, the OUT endpoint's wMaxPacketSize. This bounds total_length by the buffer size while keeping each packet length aligned to a whole output frame. BUG: KASAN: out-of-bounds in usb6fire_pcm_in_urb_handler (sound/usb/6fire/pcm.c:338) Write of size 18446744073709551456 at addr ffff88802a3d0000 by task vhci_rx/5018 Call Trace: dump_stack_lvl (lib/dump_stack.c:94 lib/dump_stack.c:120) print_report (mm/kasan/report.c:378 mm/kasan/report.c:482) kasan_report (mm/kasan/report.c:595) kasan_check_range (mm/kasan/generic.c:186 mm/kasan/generic.c:200) __asan_memset (mm/kasan/shadow.c:84) usb6fire_pcm_in_urb_handler (sound/usb/6fire/pcm.c:338) __usb_hcd_giveback_urb (drivers/usb/core/hcd.c:1657) usb_hcd_giveback_urb (drivers/usb/core/hcd.c:1741) vhci_rx_loop (drivers/usb/usbip/vhci_rx.c:107 drivers/usb/usbip/vhci_rx.c:242) kthread (kernel/kthread.c:436) ret_from_fork (arch/x86/kernel/process.c:158) ret_from_fork_asm (arch/x86/entry/entry_64.S:245) Allocated by task 10: __kmalloc_cache_noprof (mm/slub.c:5563) usb6fire_pcm_init (sound/usb/6fire/pcm.c:560 sound/usb/6fire/pcm.c:595) usb6fire_chip_probe (sound/usb/6fire/chip.c:133) usb_probe_interface (drivers/usb/core/driver.c:399) The buggy address belongs to the object at ffff88802a3d0000 which belongs to the cache kmalloc-8k of size 8192 The buggy address is located 0 bytes inside of 4832-byte region [ffff88802a3d0000, ffff88802a3d12e0) Kernel panic - not syncing: Fatal exception in interrupt | 19 Oct |
| CVE-2026-98274 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: net: psp: avoid conflicts with skb->decrypted and sk_validate_xmit_skb() PSP conflicts with TLS ULP in its usage of both skb->decrypted and sk->sk_validate_xmit_skb(). Make PSP mutually exclusive with TLS ULP, the only other user of either of these. As other users of skb->decrypted come along, they can be added to sk_has_decrypt_user(). It would make sense to also assert that sk->sk_validate_xmit_skb() is also NULL in both of these setup paths for similar future proofing, but the PSP listener/sk_clone() path is still broken and it could be seen as a regression to not allow rx assoc to run on a child of a listener socket with PSP tx assoc state. Include all TCP ULPs in the sk_has_decrypt_user() check, even though TLS is the only one that conflicts with PSP via the decrypted bit. This is intentional because PSP was not designed to be used with ULPs. It is best to close off surface area that may make bugs reachable, until someone wishes to design and test an actual user of PSP with ULPs. | 19 Oct |
| CVE-2026-98273 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: x86/kprobes: Fix crash when probing CS CALL instructions When using eBPF to probe CS CALL instructions within a function, a crash can be triggered. The eBPF tool probes offset 257 of the __hrtimer_run_queues() function: <__hrtimer_run_queues+249>: nopl 0x0(%rax,%rax,1) <__hrtimer_run_queues+254>: mov %r14,%rdi <__hrtimer_run_queues+257>: cs call <__x86_indirect_thunk_r12> <__hrtimer_run_queues+263>: mov %eax,%r12d <__hrtimer_run_queues+266>: xchg %ax,%ax <__hrtimer_run_queues+268>: mov %r13,%rdi Which triggers this crash: BUG: unable to handle page fault for address: 00000000000f41c9 #PF: supervisor write access in kernel mode #PF: error_code(0x0002) - not-present page PGD 0 P4D 0 Oops: 0002 [#1] SMP NOPTI CPU: 1 PID: 0 Comm: swapper/1 Kdump: loaded Tainted: P RIP: 0010:__hrtimer_run_queues+0x106/0x230 Note that __hrtimer_run_queues+0x106 is __hrtimer_run_queues+262, which is at the 6th byte of the above CS CALL instruction. Since the CS CALL instruction occupies 6 bytes, the exception occurred in the middle of that call instruction. The root cause is that when using eBPF tools to probe in the middle of a function, a kprobe with INT3 is used as the underlying implementation. During single-step emulation of the original CALL instruction, int3_emulate_call() assumes that the probed CALL instruction is 5 bytes long. However, the actual CS-prefixed CALL instruction occupies 6 bytes, so it constructs an incorrect exception return address. When the CPU returns from the kprobe handler, the next instruction to be executed is at the address of the last byte of that CS CALL instruction. Coincidentally, starting from that address, the CPU fetches and decodes a completely different instruction, which ultimately triggers a kernel crash. Fix the issue by using the actual instruction length obtained from the instruction decoder when constructing the exception return address, rather than relying on the hardcoded CALL_INSN_SIZE macro. [ mingo: Refined the changelog ] | 19 Oct |
| CVE-2026-98065 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: bpf: Reject key-less BTF for hash maps map_check_btf() allows a key-less BTF (btf_key_type_id == 0) only for maps that have a ->map_check_btf callback, and leaves the actual decision to that callback. Hash maps used to have no ->map_check_btf, so a key-less BTF was rejected outright. That changed when htab and rhtab gained a ->map_check_btf to register a dtor - htab in commit 1df97a7453ee ("bpf: Register dtor for freeing special fields") and rhtab in commit 6905f8601298 ("bpf: Allow special fields in resizable hashtab"). Neither looks at the key, so a key-less hash map now passes map_check_btf() and gets created. Reading it back through bpffs feeds the key type_id 0 into btf_type_seq_show(); btf_type_by_id() returns the void type, kind_ops[BTF_KIND_UNKN] is NULL, and btf_type_show() dereferences it: RIP: 0010:btf_type_show+0x223/0x2e0 kernel/bpf/btf.c:8232 RSP: 0018:ffffc9000399f868 EFLAGS: 00010206 RAX: dffffc0000000000 RBX: 0000000000000000 RCX: 0000000000000000 RDX: 0000000000000005 RSI: 0000000000000000 RDI: 0000000000000028 RBP: 0000000000000000 R08: 0000000000000001 R09: 0000000000000000 R10: ffffc9000399f970 R11: 0000000000000001 R12: ffffffff9b96b140 R13: ffffc9000399f8e0 R14: ffff88803d393c00 R15: 0000000000000003 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000200000000000 CR3: 000000003d213000 CR4: 0000000000352ef0 DR0: 0000000039ae8f55 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 Call Trace: <TASK> btf_type_seq_show_flags+0xca/0x120 kernel/bpf/btf.c:8250 htab_map_seq_show_elem+0x12e/0x350 kernel/bpf/hashtab.c:1669 map_seq_show+0x13d/0x1e0 kernel/bpf/inode.c:293 traverse.part.0.constprop.0+0x107/0x650 fs/seq_file.c:112 traverse fs/seq_file.c:99 [inline] seq_read_iter+0x93f/0x1270 fs/seq_file.c:196 seq_read+0x344/0x4d0 fs/seq_file.c:163 vfs_read+0x1e4/0xb40 fs/read_write.c:572 ksys_pread64 fs/read_write.c:764 [inline] __do_sys_pread64 fs/read_write.c:772 [inline] __se_sys_pread64 fs/read_write.c:769 [inline] __x64_sys_pread64+0x1eb/0x250 fs/read_write.c:769 do_syscall_x64 arch/x86/entry/syscall_64.c:61 [inline] do_syscall_64+0x123/0x790 arch/x86/entry/syscall_64.c:84 entry_SYSCALL_64_after_hwframe+0x77/0x7f Reject a key-less BTF in htab_map_check_btf() and rhtab_map_check_btf(), restoring the previous behavior. | 19 Oct |
| CVE-2026-97942 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: x86/alternatives: Exclude text poking against change_page_attr() From time to time, the following BUG can be observed in the x86 alternatives patching code [0]: > kernel BUG at arch/x86/kernel/alternative.c:2576! > Oops: invalid opcode: 0000 [#1] SMP NOPTI > CPU: 0 UID: 0 PID: 355 Comm: (udev-worker) Not tainted 7.1.3-1-default #1 PREEMPT(full) openSUSE Tumbleweed 8c1795b03ec64f997e57a8ad38b1161e3b98da64 > Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS unknown 02/02/2022 > RIP: 0010:__text_poke+0x2aa/0x450 > Call Trace: > <TASK> > smp_text_poke_batch_finish+0x2a7/0x320 > __static_call_transform+0xb7/0x220 > arch_static_call_transform+0x5b/0xb0 > __static_call_init+0xe9/0x270 > static_call_module_notify+0x11f/0x150 > notifier_call_chain+0x61/0xe0 > blocking_notifier_call_chain_robust+0x63/0xc0 > load_module+0x1c92/0x20c0 > init_module_from_file+0xd8/0x140 > idempotent_init_module+0x100/0x2f0 > __x64_sys_finit_module+0x71/0xe0 > do_syscall_64+0xe1/0x610 > entry_SYSCALL_64_after_hwframe+0x76/0x7e which matches the following BUG_ON() in alternative.c: /* * If something went wrong, crash and burn since recovery paths are not * implemented. */ BUG_ON(!pages[0] || (cross_page_boundary && !pages[1])); This can happen if vmalloc_to_page() fails, for any reason. Such can happen if text poking races with CPA, which can possibly result in the collapsing of page tables (or breaking of PMD hugepages). It is not a problem for most users of vmalloc_to_page() (they solely own the vmalloc'd range) but, when CONFIG_ARCH_HAS_EXECMEM_ROX=y, various modules own a single execmem vmalloc range, and can call set_memory_*() in parallel on it. This can happen to race against __text_poke and cause havoc in vmalloc_to_page(). Fix it by excluding against CPA using the init_mm mmap read lock. [ dhansen: Fix up SoB ordering. The actual code flow here was: Pedro=>Lorenzo=>Mike=>Me which is reflected in the SoB chain now. I *believe* Mike simply picked up Lorenzo's update to Pedro's post from the Link ] | 19 Oct |
| CVE-2026-97618 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: io_uring/net: don't overconsume buffers when using MSG_TRUNC When a recv/recvmsg is issued with MSG_TRUNC and the incoming packet is larger than the provided buffer, the net layer returns the full length of the packet rather than the number of bytes actually copied into the buffer. As a result, io_uring advances more of the provided buffer ring than was actually filled. Use the actual filled region size to consume the buffer, but still return the full size to preserve MSG_TRUNC semantics. Take care with multishot, because that seems to already truncate the consumption based on the available payload size. This was reported in https://github.com/axboe/liburing/issues/1619. [axboe: fold in size_t unsigned fix] | 19 Oct |
| CVE-2026-93276 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: phy: renesas: phy-rcar-gen3-usb2: Fix devm action registration for disabled VBUS regulator devm_regulator_get_exclusive() initialises the regulator with enable_count = 1, requiring the consumer to disable it before release. The devm disable action was previously only registered when the caller explicitly requested enable, so when the regulator was left in its initial enabled state without an explicit enable call, the cleanup path skipped decrementing enable_count, triggering a WARN_ON during regulator release on device removal. Fix this by always registering the devm disable action based on the actual enabled state via regulator_is_enabled(), regardless of whether the caller requested an explicit enable. This covers both the explicitly enabled case and the initial state set by devm_regulator_get_exclusive(). | 19 Oct |
| CVE-2026-93253 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: sched/isolation: Defer freeing of cpumask memblock memory to initcall When testing a linux-next kernel with commit 59bd1d914bb5 ("memblock: warn when freeing reserved memory before memory map is initialized"), the following warning was hit when there was a "nohz_full" kernel boot parameter. Cannot free reserved memory because of deferred initialization of the memory map WARNING: mm/memblock.c:904 at __free_reserved_area+0xde/0xf0, CPU#0: swapper/0/0 : Call Trace: <TASK> memblock_phys_free+0xcb/0x100 housekeeping_init+0x14c/0x170 start_kernel+0x207/0x450 x86_64_start_reservations+0x24/0x30 x86_64_start_kernel+0xda/0xe0 common_startup_64+0x13e/0x141 </TASK> IOW, we shouldn't free memblock allocated memory so early in the boot process when memory map isn't fully initialized in deferred_init_memmap(). Fix it by saving the housekeeping cpumask memblock memory to be freed into a llist free list in housekeeping_init() and add a new housekeeping_late_init() helper to defer the actual freeing of memblock memory to when initcall's are being processed. The cpumask memblock memory is treated as a llist_node with the size of a "long" type which is also smallest cpumask size that can be allocated. The non-atomic version of the llist APIs are used as there is no contention. This commit depends on the presence of commit 7c2eee9c1367 ("memblock: don't touch memblock arrays when memblock_free() is called late") to prevent a KASAN UAF bug report [1]. [1] https://lore.kernel.org/lkml/[email protected]/ | 19 Oct |
| CVE-2026-93188 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: HID: roccat: bound device-supplied profile index kone_keep_values_up_to_date() and kone_profile_activated() use an 8-bit, device-supplied profile value as an index into the 5-element kone->profiles[] array without a range check. A malicious USB device claiming the Roccat Kone id can send a switch-profile event (or a startup_profile read at probe) with an out-of-range value and make the driver read out of bounds; the result is exposed via the actual_dpi sysfs attribute. Reject out-of-range indices in both paths. This was found with static analysis and confirmed with the KUnit test added in the following patch (KASAN: slab-out-of-bounds). | 19 Oct |
| CVE-2026-90431 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: remoteproc: Prevent crash handling to race with rproc_del() There's no synchronization between rproc_crash_handler_work() and rproc_del(), as such it's possible for a driver to be removed while crash-handler work is scheduled, or even executing - resulting in use-after-free issues. To avoid this the scheduled work need to be cancelled and synchronized against before the removal proceeds. In order to ensure that this doesn't race with the reporting, and thereby scheduling new work, a "deleting" flag is introduced. This is similar to the RPROC_DELETE state that was introduced to ensure that "start" didn't race with rproc_del(), but the existing mechanism can not be used as it's valid to call rproc_report_crash() in atomic context - and the "state" is protected by a mutex. In the event that work is cancelled the pm_stay_awake() is left unbalanced and need to be unrolled. The blocking and cancelling of crash-handler work prior to the actual rproc_shutdown() call does have the explicit side-effect that crashes resulting from the shutdown process will not enter the crash-handling path, and as such will not generate devcoredumps etc. Due to the existing mutual exclusion between these code paths there's no concrete reduction in functionality, but further work would be needed to handle this case. | 19 Oct |
| CVE-2026-90279 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: md/raid5: round bitmap stripes with sector division raid5_bitmap_sector_map() aligns the array range to full RAID5 stripe widths before converting it to component sectors. That width is chunk_sectors multiplied by the number of data disks, and it is not always a power of two. Reproduce with a 4-disk RAID5, 1024-sector chunks, and three data disks. The full-stripe width is 3072 sectors. For a one-sector write at array sector 3072, correct rounding gives array range [3072, 6144), which maps to component range [1024, 2048). The old round_down()/round_up() logic instead gives [1024, 4096), which maps to [0, 1024). Use sector_div() based arithmetic so the rounded range is aligned to the actual RAID5 stripe width. The deterministic mapper test now reports the fixed component range as [1024, 2048), while the old mask-based range was [0, 1024). | 19 Oct |
| CVE-2026-90216 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: ubi: Fix rollback for explicit UBI device numbers ubi_init_attach() rolls back module initialization failures by scanning ubi_devices[0..i-1], where i is the mtd= parameter index. That assumes the parameter index matches the UBI device number. That assumption is not true when mtd= specifies an explicit ubi_num. A successfully attached device can be stored at a higher ubi_devices[] slot, and a later failure can miss it during rollback. Scan the full ubi_devices[] array and detach by the actual array index, matching the way UBI devices are stored. | 19 Oct |
| CVE-2026-90171 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: smb: smbdirect: release pending child sockets outside the handler lock smbdirect_socket_destroy() releases the listener's pending/ready child sockets while still holding the listener's handler lock, the &id_priv->handler_mutex taken via rdma_lock_handler(), not sc->listen.lock, and before the listener's own rdma_destroy_id(). That ordering has one real consequence and one cosmetic one. The real one: smbdirect_socket_release() drops the child's last reference, which destroys the child's cm_id. Doing that before the listener's rdma_destroy_id() lets _cma_cancel_listens(), running from the listener's _destroy_id(), walk an already freed child id_priv, which KASAN catches as a slab-use-after-free during listener shutdown: [ 4758.909130] BUG: KASAN: slab-use-after-free in __mutex_lock+0x1469/0x1560 [ 4758.911450] Read of size 1 at addr ffff88821c381db4 by task ksmbd.control/1652 [ 4758.913262] Call Trace: [ 4758.913267] <TASK> [ 4758.913299] __mutex_lock+0x1469/0x1560 [ 4758.913408] _cma_cancel_listens+0x312/0x3b0 [ 4758.913413] _destroy_id+0x363/0xee0 [ 4758.913417] smbdirect_socket_destroy_sync+0x17d5/0x2440 [ 4758.913443] smbdirect_socket_release+0x124/0x230 [ 4758.913451] ksmbd_rdma_stop_listening+0x9f/0x190 [ 4758.913457] ksmbd_conn_transport_destroy+0x65/0x3c0 [ 4758.913463] kill_server_store+0x1fb/0x2b0 [ 4758.913501] kernfs_fop_write_iter+0x349/0x4d0 [ 4758.913507] vfs_write+0x5e7/0xc70 [ 4758.913528] ksys_write+0x12a/0x210 [ 4758.913541] do_syscall_64+0x135/0x460 [ 4758.913555] entry_SYSCALL_64_after_hwframe+0x77/0x7f The cosmetic one: releasing a child recurses into smbdirect_socket_destroy(), which takes the child's own rdma_lock_handler() lock nested under the listener's. The listener's and the child's cm_id are always different instances, so this cannot deadlock for real; the CM core itself nests a new connection id's handler_mutex under the listening id's in cma_ib_req_handler(). But lockdep only sees one lock class, reports possible recursive locking, and then disables itself, hiding real locking bugs for the rest of the run: [ 2424.579653] WARNING: possible recursive locking detected [ 2424.581180] 7.1.0-next-20260623+ #89 Not tainted [ 2424.582548] -------------------------------------------- [ 2424.584500] ksmbd.control/8854 is trying to acquire lock: [ 2424.586817] ffff888102303c20 (&id_priv->handler_mutex){+.+.}-{4:4}, at: smbdirect_socket_destroy_sync+0xc39/0x2440 [ 2424.590590] [ 2424.590590] but task is already holding lock: [ 2424.591601] ffff888102046c20 (&id_priv->handler_mutex){+.+.}-{4:4}, at: smbdirect_socket_destroy_sync+0xc39/0x2440 [ 2424.594178] [ 2424.594178] other info that might help us debug this: [ 2424.596634] Possible unsafe locking scenario: [ 2424.596634] [ 2424.598841] CPU0 [ 2424.599765] ---- [ 2424.600695] lock(&id_priv->handler_mutex); [ 2424.601836] lock(&id_priv->handler_mutex); [ 2424.602590] [ 2424.602590] *** DEADLOCK *** [ 2424.602590] [ 2424.604512] May be due to missing lock nesting notation Splice the pending/ready children onto a local list under the listener's listen.lock, while the handler lock is held so a concurrent CM CONNECT_REQUEST cannot add more, but defer the actual smbdirect_socket_release() calls until after the listener's cm_id has been destroyed and its handler lock dropped. The children are independent sockets whose teardown needs neither the listener's handler lock nor its cm_id. Found with ksmbdzzer [2], a KSMBD fuzzer that drives libFuzzer with a kcov-dataflow [1] coverage vector: it folds each instrumented comparison/argument's runtime operand value together with its PC (the default arm mixes them as pc⊕val) so that a new operand value at a known site counts as new coverage. [1] https://lwn.net/Articles/1077606/ [2] https://github.com/yskzalloc/kcov-dataflow | 19 Oct |
| CVE-2026-90096 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: fuse: invalidate the correct range after O_APPEND direct write fuse_direct_write_iter() captures pos before generic_write_checks(), which moves ki_pos to EOF for O_APPEND writes: fuse_direct_write_iter() { pos = iocb->ki_pos; /* 0 (user-supplied) */ generic_write_checks(); /* ki_pos -> EOF */ fuse_direct_io(); /* writes at EOF, correct */ invalidate(pos, pos + res); /* [0, res) -- wrong */ } The post-write invalidation targets a stale range instead of the actual written range at EOF. This can cause data inconsistency when the file size is not page-aligned. The tail page straddling EOF has a valid portion before EOF that concurrent readers can fault back in during the DIO write window: Tail page (file size X not page-aligned): page_start X (EOF) page_end |--- valid data ----|-- stale --| CPU0 (O_APPEND DIO writer) CPU1 (buffered reader) -------------------------- ---------------------- invalidate [X, X+len) tail page evicted FUSE_WRITE in flight ... read [page_start, X) tail page re-faulted [X, page_end) = stale FUSE_WRITE completes i_size = X + len invalidate [0, len) <- WRONG tail page still cached read [X, X+len) hits stale tail page returns old data Fix by reading pos back from iocb->ki_pos after generic_write_checks(), as generic_file_direct_write() does. Also fix a typo in the comment ("may have" -> "may have competed"). | 19 Oct |
| CVE-2026-90078 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: net/sched: act_skbmod: fix length calculations and avoid invalid header warnings syzbot reported a warning in skb_network_header_len() triggered by tcf_skbmod_act(): !skb_transport_header_was_set(skb) WARNING: CPU: 0 PID: 14949 at include/linux/skbuff.h:3243 skb_network_header_len include/linux/skbuff.h:3243 [inline] WARNING: CPU: 0 PID: 14949 at net/sched/act_skbmod.c:55 tcf_skbmod_act+0xfe8/0x1810 net/sched/act_skbmod.c:55 There are a few issues in tcf_skbmod_act(): 1. Calling skb_network_header_len() assumes skb->transport_header is set, which is not guaranteed when tcf_skbmod_act() runs at TC ingress. 2. Unconditionally calling skb_mac_header_len() at the beginning of tcf_skbmod_act() triggers a warning on L3 devices (e.g. TUN) where the MAC header is unset, evaluating to an underflowed garbage length. 3. On TC ingress, skb->data points to the network header. Adding the MAC header length to the IP header length causes skb_ensure_writable() to request more bytes than the actual IP packet length, dropping valid short packets (e.g. 28-byte UDP/IPv4 packets). Fix these by: - Using skb_network_offset(skb) + sizeof(struct iphdr/ipv6hdr) for SKBMOD_F_ECN so that the required length is correctly calculated on both ingress (offset == 0) and egress (offset == mac_len). - Setting max_edit_len to ETH_HLEN for Ethernet header modifications after validating ARPHRD_ETHER. | 19 Oct |
| CVE-2026-90015 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: xhci: fix lost bounce buffers on TDs spanning several ring segments When a TD reaches a link TRB with data that is not aligned to the endpoint's wMaxPacketSize, xhci_align_td() stages the unalignable tail through the bounce buffer of the ring segment holding that link TRB. xhci_unmap_td_bounce_buffer() later unmaps it and, for IN transfers, copies the data back into the URB's buffer. The enqueue path records the segment that was bounced in td->bounce_seg, under the assumption that a TD never spans more than two ring segments. That assumption does not hold: a TD large enough to span three or more segments crosses several link TRBs and can be bounced at each of them. Only the last one survives in td->bounce_seg, so every earlier bounce buffer is neither copied back nor DMA unmapped. The URB still completes with actual_length equal to the requested length and no error, so the transfer looks successful while a wMaxPacketSize sized hole in the destination buffer silently keeps its previous contents. It also leaks a DMA mapping per dropped bounce. Any sufficiently large and fragmented bulk transfer can hit this. It was found with a USB mass storage device behind xHCI backing a dm-verity target with 512 byte hash blocks, where the stale data is detected rather than silently consumed. The device enumerates as SuperSpeed, so wMaxPacketSize is 1024, while dm-bufio issues one 512 byte bio per hash block. verity_prefetch_io() makes the block layer merge hundreds of them into a single request of up to 512 scatterlist entries of 512 bytes each. At 256 TRBs per ring segment such a TD spans three segments, and every segment boundary falls on an odd multiple of 512, i.e. unaligned to wMaxPacketSize. dm-bufio then caches a hash block holding stale data and dm-verity declares the metadata block corrupted: device-mapper: verity: 8:2: metadata block 10850 is corrupted A reproducer running this under qemu is available at https://github.com/baloo/xhci-verity The bounce state (bounce_buf, bounce_dma, bounce_len, bounce_offs) already lives on the ring segment, so there is nothing extra to track. Keep recording the last bounced segment in td->bounce_seg and, on completion, walk the segments from td->start_seg up to it, unmapping every segment that still has a pending bounce. Stopping at td->bounce_seg rather than td->end_seg matters: a bounce implies the TD continues past that segment's link TRB, so bounce_seg is always strictly before end_seg, and a later TD may already have started in end_seg and been bounced there. Walking that far would copy a foreign bounce buffer into this URB and unmap it twice. It also keeps the walk correct if a TD ever wraps the whole ring so that end_seg == start_seg. [mn: Add ring->num_segs check to prevent unlikely infinite for loop.] | 19 Oct |
| CVE-2026-89948 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: batman-adv: bla: fix freeing of claims on meshif deletion When the mesh interface is getting deleted, then batadv_bla_del_backbone_claims() (via batadv_bla_purge_backbone_gw()) could make sure that all claims gets removed. But this function is only executed when bat_priv->bla.claim_hash is not NULL. And since batadv_bla_free() is always setting it to NULL before it is (indirectly) called, it was never actually executed. But the batadv_bla_purge_claims() -> batadv_handle_unclaim() is at the moment too fragile because the BLA code is not handling the rehashing in batadv_bla_update_orig_address(). The stored backbone address doesn't have to be the one actually used for the hash bucket selection during the initial adding of the backbone. The batadv_handle_unclaim() can therefore fail to find the respective backbone for the unclaim and then stop the deletion. But the actual backbone_gw object is not needed for the unclaim because all relevant information is always provided by the caller. And the check for the existence of the backbone_gw doesn't provide any additional security check for the deletion of a claim. | 19 Oct |
| CVE-2026-89917 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: KVM: arm64: Handle VNCR TLB invalidation race with vcpu_put() VNCR unmapping While VNCR TLB invalidation always occurs under the MMU lock, vcpu_put() doesn't, while it unmaps the VNCR page. The problem is that the invalidation evaluates vncr_tlb::cpu to decide whether an unmapping needs to take place (cpu != -1) before performing it. On the other hand, this_cpu_reset_vncr_fixmap() unconditionally unmaps if L1_VNCR_MAPPED is set. These two obviously can race, with a TOCTOU pattern on the TLBI path, and a BUG_ON() on the vcpu_put() path. And the two can end-up calling vncr_fixmap(-1), with extra lethal effects. Move the reset of vncr_tlb::cpu to -1 to a common function, and make this update atomic so that only a single thread can reset the field and perform the corresponding unmap. The vcpu_put() still need to unconditionally unmap the current VNCR to close another ugly race. Finally, the assignment of vncr_tlb::cpu is moved to be kept in sync with the actual mapping, similar to L1_VNCR_MAPPED being set. | 19 Oct |
| CVE-2026-89839 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: f2fs: use the mount idmap for the owner check in f2fs_xattr_advise_set() f2fs_xattr_advise_set() calls inode_owner_or_capable() with &nop_mnt_idmap before allowing the "system.advise" xattr to be set, instead of the idmap that the VFS passes to the ->set() handler. f2fs supports idmapped mounts, so on such a mount this checks the caller's fsuid against the unmapped on-disk owner rather than the mapped owner: the actual owner can be wrongly denied with -EPERM and an unrelated caller wrongly allowed. Pass the handler's idmap instead. | 19 Oct |
| CVE-2026-89455 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: PCI: plda: Fix use-after-free of event IRQs during teardown plda_pcie_irq_domain_deinit() removes pcie->event_domain via irq_domain_remove(), but the per-event IRQs mapped from that domain are requested with devm_request_irq() in plda_init_interrupts(). The actual free_irq() for a devm-managed IRQ is deferred by devres until after the calling probe()/remove() function returns. This means irq_domain_remove() can free the domain's internal data before the deferred free_irq() for IRQs still mapped into it has run. When devres later processes that deferred cleanup, it can end up dereferencing the already-freed domain. Free each event IRQ explicitly with devm_free_irq() before removing the domain. This triggers the free immediately and removes the IRQ from the devres tracking list, so devres will not attempt to free it a second time later. Also dispose of the event, INTx, and MSI IRQ mappings with irq_dispose_mapping() before their owning domains are removed. Finally, guard the calls to irq_set_chained_handler_and_data() for pcie->irq, pcie->msi_irq, and pcie->intx_irq so they only run when those fields hold a valid (>0) IRQ number. This is a pre-existing issue, flagged by automated review during work on an earlier, unrelated patch to this driver. Build-tested and boot-tested on StarFive VisionFive v1.2A board | 19 Oct |
| CVE-2026-80973 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: ALSA: 6fire: bound the MIDI event length from the device usb6fire_comm_receiver_handler() forwards a MIDI event using a length byte the device supplies, with no bound and no check that the transfer delivered that many bytes: if (!urb->status) { if (rt->receiver_buffer[0] == 0x10) /* midi in event */ if (midi_rt) midi_rt->in_received(midi_rt, rt->receiver_buffer + 2, rt->receiver_buffer[1]); } receiver_buffer is a 64-byte kzalloc() buffer (COMM_RECEIVER_BUFSIZE), so only 62 bytes follow the two-byte header. receiver_buffer[1] is a u8 the device chooses, so a device that answers with 0x10 and a length of 0xFF makes snd_rawmidi_receive() read 255 bytes starting two bytes into a 64-byte object. The bytes past the buffer are handed to userspace through the rawmidi read path. urb->actual_length is not consulted either, so a short transfer leaves both the type byte and the length byte at their previous values and the handler acts on stale data. The receiver URB is submitted from usb6fire_comm_init() at probe, so the read happens on plug with no user action; forwarding to userspace also needs a MIDI input substream open, since usb6fire_midi_in_received() only calls snd_rawmidi_receive() when rt->in is set. KASAN on 7.2.0-rc5 (arm64), single packet from an emulated device: BUG: KASAN: slab-out-of-bounds in snd_rawmidi_receive Read of size 255 at addr ffff000009f64682 by task bash/183 __asan_memcpy snd_rawmidi_receive usb6fire_midi_in_received [snd_usb_6fire] usb6fire_comm_receiver_handler [snd_usb_6fire] Allocated by task 11: usb6fire_comm_init [snd_usb_6fire] usb6fire_chip_probe [snd_usb_6fire] The buggy address is located 2 bytes inside of allocated 64-byte region [ffff000009f64680, ffff000009f646c0) Reject the event when the length exceeds the bytes that follow the header, and require the transfer to have delivered the header plus that many bytes. The receiver URB is submitted with a 64-byte transfer_buffer_length, so a genuine device cannot deliver an event longer than those 62 bytes and nothing valid is dropped. Discovered by XBOW, triaged by Baul Lee <[email protected]> | 19 Oct |
| CVE-2026-80970 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: ALSA: FCP: do not copy out an uninitialised init response fcp_ioctl_init() allocates its response buffer with kmalloc() and copies the whole buffer back to userspace: buf_size = init.step0_resp_size + init.step2_resp_size; void *resp __free(kfree) = kmalloc(buf_size, GFP_KERNEL); ... if (copy_to_user(arg->resp, resp, buf_size)) return -EFAULT; Nothing clears the buffer, and the only writer of its leading step0_resp_size bytes is the step-0 control transfer: err = snd_usb_ctl_msg(dev, usb_rcvctrlpipe(dev, 0), FCP_USB_REQ_STEP0, USB_RECIP_INTERFACE | USB_TYPE_CLASS | USB_DIR_IN, 0, private->bInterfaceNumber, step0_resp, private->step0_resp_size); if (err < 0) return err; usb_fill_control_urb() does not set URB_SHORT_NOT_OK, so a short or zero-length data stage completes with status 0 and snd_usb_ctl_msg() returns a small actual_length. The only check is err < 0, so a short transfer is accepted as success. snd_usb_ctl_msg() copies the full size back unconditionally: buf = kmemdup(data, size, GFP_KERNEL); ... memcpy(data, buf, size); Bytes the device never wrote are therefore restored into resp unchanged and copied to userspace. step0_resp_size and step2_resp_size are each validated only to 1..255, so the caller also picks the slab cache, from kmalloc-8 up to kmalloc-512. On 7.2.0-rc5 (arm64), device answering step 0 with a zero-length data stage, s0 = s2 = 255: # init_on_alloc off, no spray step0 window [0,255): nonzero=94/255 000: 00 80 60 06 00 00 ff ff 18 00 00 00 57 01 ea 01 010: 08 78 22 13 00 00 ff ff a8 c4 5f 80 00 80 ff ff # same kernel, kmalloc-512 pre-seeded with an 8-byte tag step0 window [0,255): nonzero=219/255 tagbytes=232 # identical run, init_on_alloc=1 step0 window [0,255): nonzero=0/255 tagbytes=0 # all three runs step2 window [255,510): device words matched=62/62 a8 c4 5f 80 00 80 ff ff is the little-endian kernel text address ffff8000805fc4a8. The step-2 window is unaffected, so the disclosure is exactly the step-0 region. Zero the buffer, and require the step-0 transfer to deliver the full step0_resp_size bytes so a short data stage is reported as an error. Discovered by XBOW, triaged by Baul Lee <[email protected]> | 19 Oct |
| CVE-2026-80834 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: crypto: sun8i-ce - Remove crypto_rng interface Since the crypto_rng interface for hardware PRNGs is unused and is redundant with hwrng and the actual Linux RNG, it's being phased out. Most drivers for it were already removed. Go ahead and remove the sun8i-ce support which is one of the only remaining ones. Note that the sun8i-ce support for hwrng remains in place. That is the interface that actually matters. As usual for crypto_rng, this driver was also buggy: its ->generate() function had a use-after-free vulnerability due to using wait_for_completion_interruptible_timeout() without handling shutting down the DMA operation if a signal is sent. There's no point in fixing this separately only to remove the code anyway, so this commit is marked with Fixes and Cc stable. | 19 Oct |
| CVE-2026-80833 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: crypto: sun8i-ss - Remove crypto_rng interface Since the crypto_rng interface for hardware PRNGs is unused and is redundant with hwrng and the actual Linux RNG, it's being phased out. Most drivers for it were already removed. Go ahead and remove the sun8i-ss support which is one of the only remaining ones. As usual for crypto_rng, this driver was also buggy: its ->generate() function had a use-after-free vulnerability due to using wait_for_completion_interruptible_timeout() without handling shutting down the DMA operation if a signal is sent. Also, it had a buffer overread bug in the line 'memcpy(ctx->seed, d + dlen, ctx->slen);'. There's no point in fixing these bugs separately only to remove the code anyway, so this commit is marked with Fixes and Cc stable. | 19 Oct |
| CVE-2026-80827 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: USB: serial: option: fix slab OOB read in interrupt URB callback The interrupt URB buffer is allocated in setup_port_interrupt_in() based on the endpoint's wMaxPacketSize: buffer_size = usb_endpoint_maxp(epd); port->interrupt_in_buffer = kmalloc(buffer_size, GFP_KERNEL); When a USB device declares wMaxPacketSize = 8 on its interrupt IN endpoint, the buffer is allocated from kmalloc-8 cache (exactly 8 bytes). If the device sends a short packet (actual_length < wMaxPacketSize), the URB completes with status == 0 and the callback proceeds to read: data[sizeof(struct usb_ctrlrequest)] which evaluates to data[8], accessing 1 byte beyond the allocated 8-byte buffer. This results in a slab out-of-bounds read. Fix this by adding the missing bounds check: first verify that the actual length is large enough to contain the struct usb_ctrlrequest header before accessing req_pkt->bRequestType and req_pkt->bRequest, and then verify that there is an additional byte for the modem signal state before reading data[sizeof(struct usb_ctrlrequest)] inside the conditional. Use sizeof(*req_pkt) instead of sizeof(struct usb_ctrlrequest) for consistency. [ johan: use dev_err(); split signals declaration and initialisation ] | 19 Oct |
| CVE-2026-80823 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: nfc: st21nfca: validate ATR_REQ length against the received frame st21nfca_tm_recv_atr_req() checks that the received ATR_REQ frame is at least ST21NFCA_ATR_REQ_MIN_SIZE and that the self-declared atr_req->length is at least sizeof(struct st21nfca_atr_req), but never checks that atr_req->length does not exceed the actual received length (skb->len). st21nfca_tm_send_atr_res() then trusts the declared length: gb_len = atr_req->length - sizeof(struct st21nfca_atr_req); ... memcpy(atr_res->gbi, atr_req->gbi, gb_len); so an RF peer that sends a short frame but sets atr_req->length larger than the frame makes gb_len exceed the general bytes actually present, and the memcpy reads out of bounds past the received skb. Those bytes are placed in the ATR_RES and sent back to the peer (kernel-memory disclosure to a proximity attacker); a larger declared length is an out-of-bounds read (DoS). Reject frames whose declared length exceeds the received length. The adjacent nfc_tm_activated() path in the same function already derives its general-bytes length from skb->len rather than the declared field. Found by 0sec (https://0sec.ai) using automated source analysis; the missing bound is evident from source. Compile-tested. | 19 Oct |
| CVE-2026-80801 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: nfc: microread: validate target discovery payload lengths microread_target_discovered() parses target discovery payloads from skb->data according to the HCI gate. The fixed field offsets and UID copies were checked only against the destination nfc_target buffers, not against the actual skb length. Validate that each gate-specific payload contains the fixed fields and UID bytes before reading or copying them. | 19 Oct |
| CVE-2025-68316 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: scsi: ufs: core: Fix invalid probe error return value After DME Link Startup, the error return value is set to the MIPI UniPro GenericErrorCode which can be 0 (SUCCESS) or 1 (FAILURE). Upon failure during driver probe, the error code 1 is propagated back to the driver probe function which must return a negative value to indicate an error, but 1 is not negative, so the probe is considered to be successful even though it failed. Subsequently, removing the driver results in an oops because it is not in a valid state. This happens because none of the callers of ufshcd_init() expect a non-negative error code. Fix the return value and documentation to match actual usage. | 14 Oct |
| CVE-2026-74602 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: ring-buffer: Initialise reader page order in rb_allocate_cpu_buffer() In rb_allocate_cpu_buffer(), bpage->order was omitted, leaving it as 0. This is an issue for a ring-buffer with subbufs bigger than PAGE_SIZE if when freed: free_buffer_page() relies on this value. Align the value with the actual allocation size (buffer::subbuf_order). | 14 Oct |
| CVE-2026-74657 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: ipv4: Fix fib_nlmsg_size() for RTA_VIA nexthops fib_nlmsg_size() still estimates nexthop space as if every gateway is encoded as an IPv4 RTA_GATEWAY attribute. IPv4 routes can also carry an IPv6 gateway, which fib_nexthop_info() dumps as RTA_VIA. As a result, route notifications can allocate an skb that is too small. fib_dump_info() then fails with -EMSGSIZE and rtmsg_fib() hits the WARN_ON() that marks such failures as a fib_nlmsg_size() bug. With panic_on_warn set, this becomes a kernel panic. Mirror the actual nexthop dump layout in fib_nlmsg_size(): account for IPv6 nexthop gateways dumped as RTA_VIA, for the no-header rtnexthop layout used inside RTA_MULTIPATH, and for RTA_FLOW only when it is actually present. | 14 Oct |
| CVE-2025-68362 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: wifi: rtl818x: rtl8187: Fix potential buffer underflow in rtl8187_rx_cb() The rtl8187_rx_cb() calculates the rx descriptor header address by subtracting its size from the skb tail pointer. However, it does not validate if the received packet (skb->len from urb->actual_length) is large enough to contain this header. If a truncated packet is received, this will lead to a buffer underflow, reading memory before the start of the skb data area, and causing a kernel panic. Add length checks for both rtl8187 and rtl8187b descriptor headers before attempting to access them, dropping the packet cleanly if the check fails. | 13 Oct |
338 of 338 · Previous
Download these 338 as CSV · subscribe to this list.
EPSS scores: 2026-10-31. NVD cursor: 2026-10-29 00:22. The News page shows only notable CVEs (KEV, your stack, new criticals, EPSS over 50%, or active exploitation per SSVC); this table has all of them.