Vulnerabilities
All
My stack
Known exploited
Public exploit
Critical (9+)
Likely exploited (EPSS ≥ 50%)
Changed, 24 h
New, 24 h
Sort:
risk
modified
published
CVSS
EPSS
| CVE | CVSS | EPSS | Vendor, product | Description | Modified |
|---|---|---|---|---|---|
| CVE-2026-89482 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: nvme-tcp: do not accept C2HData based on blk_rq_payload_bytes() alone Commit 25e5cb780e62 ("nvme-tcp: fix possible crash in write_zeroes processing") established that blk_rq_payload_bytes() must not be read without first checking blk_rq_nr_phys_segments(), and recorded the result in nvme_tcp_setup_cmd_pdu() as req->data_len. The receive side was left as it was. The two differ for REQ_OP_WRITE_ZEROES, which has no physical segments but a non-zero blk_rq_bytes(), so setup leaves req->iter untouched while the receive gate lets a C2HData through and nvme_tcp_recv_data() copies into whatever the previous command on that tag left there. The driver-private area is zeroed only when the tag set is allocated. Reproduced with a test target that leaves a residual iterator on a tag and then sends a C2HData for a WRITE_ZEROES command on the same tag: BUG: KASAN: wild-memory-access in _copy_to_iter+0x642/0x1330 Write of size 512 at addr ffe728c2175dfa81 by task kworker/0:1H/103 CPU: 0 UID: 0 PID: 103 Comm: kworker/0:1H Not tainted 7.2.0-rc5-NVMETCP-gf5098b6bae76 #1 PREEMPT(lazy) Hardware name: QEMU Ubuntu 24.04 PC v2 (i440FX + PIIX, arch_caps fix, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 Workqueue: nvme_tcp_wq nvme_tcp_io_work Call Trace: <TASK> dump_stack_lvl+0x53/0x70 kasan_report+0xce/0x100 ? _copy_to_iter+0x642/0x1330 kasan_check_range+0x105/0x1b0 __asan_memcpy+0x3c/0x60 _copy_to_iter+0x642/0x1330 ? __pfx_sock_has_perm+0x10/0x10 ? worker_thread+0x45b/0xd10 ? __pfx__copy_to_iter+0x10/0x10 ? _raw_spin_lock_bh+0x83/0xe0 ? __pfx__raw_spin_lock_bh+0x10/0x10 __skb_datagram_iter+0xf3/0x820 ? __pfx_simple_copy_to_iter+0x10/0x10 ? __asan_memcpy+0x3c/0x60 ? skb_copy_bits+0x58d/0x830 skb_copy_datagram_iter+0x37/0x120 nvme_tcp_recv_skb+0xa07/0x4320 ? __pfx_nvme_tcp_recv_skb+0x10/0x10 __tcp_read_sock+0x1ab/0x810 ? __pfx_nvme_tcp_recv_skb+0x10/0x10 ? __pfx_lock_sock_nested+0x10/0x10 ? __pfx___tcp_read_sock+0x10/0x10 nvme_tcp_try_recv+0x152/0x1e0 ? __pfx_nvme_tcp_try_recv+0x10/0x10 ? __pfx_mutex_unlock+0x10/0x10 nvme_tcp_io_work+0x1e4/0x6c0 ? __schedule+0x181a/0x49f0 ? __pfx_nvme_tcp_io_work+0x10/0x10 process_one_work+0x633/0x1030 Keep the blk_rq_payload_bytes() test and add req->data_len to it. The old test is what rejects a C2HData naming a tag that is no longer in flight, because blk_update_request() zeroes rq->__data_len on completion; req->data_len and req->curr_bio are driver-private and survive completion, so they cannot stand in for it. Setup initialises the iterator only when both req->curr_bio and req->data_len are set, so the gate now tests the same two. | 19 Oct |
| CVE-2026-89479 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: sctp: stop processing a packet once its association is deleted sctp_endpoint_bh_rcv() looks the association up only when chunk->asoc is NULL, and caches the result in chunk->asoc and chunk->transport without taking a reference. A packet that matches no association is handed to the endpoint, so a peer can bundle COOKIE ECHO, SHUTDOWN and SHUTDOWN ACK in one packet. The COOKIE ECHO creates the association, the SHUTDOWN chunk caches it, and with the outqueue empty the SHUTDOWN ACK reaches sctp_sf_do_9_2_final(), so the association and its transports are freed. The endpoint loop has no counterpart to the asoc->base.dead check in sctp_assoc_bh_rcv(). The next chunk writes to last_time_heard in the freed transport and is then passed to sctp_do_sm() with the freed association. The transport is freed through RCU, so this needs the packet to come off the socket backlog, where the loop runs in task context. The endpoint loop cannot do the same check: it holds no reference on the association, so reading asoc->base.dead would itself be a use-after-free. Mark the packet for discard in the command interpreter, just before it deletes the association. That is also before sctp_inq_free() releases the chunk on the association receive path. sctp_sf_do_5_2_4_dupcook() issues SCTP_CMD_DELETE_TCB for the temporary association, while the one the packet belongs to stays alive. A restarting peer can bundle DATA behind its COOKIE ECHO, so compare against chunk->asoc and leave that case alone. | 19 Oct |
| CVE-2026-89478 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: sctp: drop a chunk if its transport was removed sctp_rcv() resolves the transport once per packet and leaves it in chunk->transport. The lookup reference, or the one sctp_add_backlog() takes if the socket is owned by userspace, keeps it around until the chunk has been processed. An authenticated ASCONF DEL-IP can remove it in the meantime. sctp_assoc_rm_peer() takes the transport out of the association and calls sctp_transport_free(), which tags it dead and drops the reference the association held. There is a window on both paths: the packet can sit on the socket backlog, and on the direct path the lookup completes before bh_lock_sock(). The DATA chunk in that packet puts the removed transport back into asoc->peer.last_data_from. Once the packet is done that reference goes away and the transport is freed by RCU, so the next delayed SACK carries the pointer into the SACK chunk and sctp_outq_select_transport() reads the freed transport's state. Drop the chunk in sctp_inq_push(), next to the existing rcvr->dead check. Both paths reach it with the association's socket lock held. The peer retransmits it. | 19 Oct |
| CVE-2026-81002 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: xdp: fix zero-copy frame layout xdp_convert_zc_to_xdp_frame() clones an XSK packet into an order-0 page and advertises PAGE_SIZE as its frame size. It allows the copied frame to occupy the page tail needed by skb_shared_info and records zero headroom even when metadata separates the frame header from packet data. An AF_XDP zero-copy packet redirected through cpumap can therefore make the skb overlap skb_shared_info or place it beyond the allocated page. Limit the copied layout to SKB_WITH_OVERHEAD(PAGE_SIZE) and include the metadata length in frame headroom. Redirect callers already handle a NULL conversion result. BUG: KASAN: slab-out-of-bounds in skb_gro_receive Write of size 4 at addr ffff88800cf37004 by task cpumap/1/map:1/146 Call Trace: skb_gro_receive (net/core/gro.c:174) udp_gro_receive (net/ipv4/udp_offload.c:812) inet_gro_receive (net/ipv4/af_inet.c:1539) dev_gro_receive (net/core/gro.c:515) gro_receive_skb (net/core/gro.c:633) cpu_map_kthread_run (kernel/bpf/cpumap.c:395) kthread (kernel/kthread.c:436) ret_from_fork (arch/x86/kernel/process.c:164) ret_from_fork_asm (arch/x86/entry/entry_64.S:255) Kernel panic - not syncing: KASAN: panic_on_warn set ... | 19 Oct |
| CVE-2026-80986 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: net/smc: bound the peer rkey counts in SMC-Rv2 LLC messages On a link whose device has max_recv_sge == 1 there is no shared v2 receive buffer, and smc_llc_save_add_link_rkeys() takes the v2 extension from 44 bytes past the start of the queue entry's inline message: ext = (struct smc_llc_msg_add_link_v2_ext *)(llc_msg + SMC_WR_TX_SIZE); The entry is a 72-byte allocation and the extension starts at offset 68, so ext->num_rkeys at offset 94 is already past it. This happens on every SMC-Rv2 link addition, whatever the peer sends: [ 2.490065] BUG: KASAN: slab-out-of-bounds in smc_llc_save_add_link_rkeys+0x333/0x350 [ 2.490431] Read of size 2 at addr ffff8880056406de by task smctest/106 [ 2.490709] [ 2.490792] CPU: 0 UID: 0 PID: 106 Comm: smctest Not tainted 7.2.0-rc5-p1-g77a5d9d9c99f #32 PREEMPT(lazy) [ 2.490795] Hardware name: QEMU Ubuntu 24.04 PC v2 (i440FX + PIIX, arch_caps fix, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 [ 2.490798] Call Trace: [ 2.490803] <TASK> [ 2.490805] dump_stack_lvl+0x53/0x70 [ 2.490810] print_report+0xd0/0x630 [ 2.490828] ? __pfx__raw_spin_lock_irqsave+0x10/0x10 [ 2.490832] ? smc_llc_save_add_link_rkeys+0x333/0x350 [ 2.490834] kasan_report+0xce/0x100 [ 2.490836] ? smc_llc_save_add_link_rkeys+0x333/0x350 [ 2.490837] smc_llc_save_add_link_rkeys+0x333/0x350 [ 2.490839] ? smcr_buf_map_lgr+0x1bf/0x2b0 [ 2.490844] smc_llc_cli_add_link+0xca7/0x1e80 [ 2.490848] ? smc_llc_wait+0x355/0x810 [ 2.490850] ? __pfx_smc_llc_wait+0x10/0x10 [ 2.490851] ? __pfx_smc_llc_cli_add_link+0x10/0x10 [ 2.490853] ? __pfx_autoremove_wake_function+0x10/0x10 [ 2.490863] __smc_connect+0x3f5c/0x4980 [ 2.490873] ? __pfx_kernel_connect+0x10/0x10 [ 2.490888] ? __pfx___smc_connect+0x10/0x10 [ 2.490891] ? release_sock+0x148/0x1d0 [ 2.490894] smc_connect+0x42c/0x580 [ 2.490896] __sys_connect+0xfc/0x130 [ 2.490898] ? __pfx___sys_connect+0x10/0x10 [ 2.490900] ? handle_mm_fault+0x1a1/0x430 [ 2.490908] __x64_sys_connect+0x6d/0xb0 [ 2.490909] ? fpregs_assert_state_consistent+0x56/0xe0 [ 2.490917] do_syscall_64+0xf9/0x540 [ 2.490921] entry_SYSCALL_64_after_hwframe+0x77/0x7f [ 2.490924] RIP: 0033:0x421bb4 [ 2.490927] Code: ff f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa 80 3d ad 34 09 00 00 74 13 b8 2a 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 4c c3 0f 1f 00 55 48 89 e5 48 83 ec 10 89 55 [ 2.490929] RSP: 002b:00007ffd473b01a8 EFLAGS: 00000202 ORIG_RAX: 000000000000002a [ 2.490935] RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 0000000000421bb4 [ 2.490936] RDX: 0000000000000010 RSI: 00007ffd473b01d0 RDI: 0000000000000003 [ 2.490937] RBP: 0000000000003930 R08: 0000000000000004 R09: 0000000000000000 [ 2.490938] R10: 00007ffd473b0f98 R11: 0000000000000202 R12: 0000000000000006 [ 2.490939] R13: 00007ffd473b0f87 R14: 0000000000000003 R15: 00007ffd473b0f90 [ 2.490940] </TASK> [ 2.490941] [ 2.499545] Allocated by task 44: [ 2.499693] kasan_save_stack+0x33/0x60 [ 2.499860] kasan_save_track+0x14/0x30 [ 2.500026] __kasan_kmalloc+0x8f/0xa0 [ 2.500190] __kmalloc_cache_noprof+0x158/0x370 [ 2.500393] smc_llc_enqueue+0x72/0x560 [ 2.500559] smc_wr_rx_tasklet_fn+0x474/0xa80 [ 2.500747] tasklet_action_common+0x20f/0x8a0 [ 2.500945] handle_softirqs+0x18e/0x590 [ 2.501115] do_softirq+0x3b/0x60 [ 2.501266] __local_bh_enable_ip+0x61/0x70 [ 2.501446] __alloc_skb+0x732/0x890 [ 2.501604] rxe_init_packet+0x16b/0x4f0 [ 2.501783] prepare_ack_packet+0xb8/0x830 [ 2.501962] rxe_receiver+0x495/0x96e0 [ 2.502125] do_work+0x144/0x470 [ 2.502269] process_one_work+0x633/0x1030 [ 2.502450] worker_thread+0x45b/0xd10 [ 2.50261 ---truncated--- | 19 Oct |
| CVE-2026-80981 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: net/smc: fix use-after-free of the LLC qentry in smc_llc_srv_add_link() smc_llc_srv_add_link() keeps add_llc pointing into the queue entry: add_llc = &qentry->msg.add_link; smc_llc.c:1482 ... smc_llc_save_add_link_info(link_new, add_llc); smc_llc.c:1494 smc_llc_flow_qentry_del(&lgr->llc_flow_lcl); smc_llc.c:1495 ... u8 *llc_msg = smc_link_shared_v2_rxbuf(link) ? (u8 *)lgr->wr_rx_buf_v2 : (u8 *)add_llc; smc_llc.c:1504 smc_llc_save_add_link_rkeys(link, link_new, llc_msg); smc_llc.c:1506 smc_llc_flow_qentry_del() kfree()s the entry, so on a link without a shared v2 receive buffer the pointer handed to smc_llc_save_add_link_rkeys() is already freed. Before the Fixes: commit that branch always used lgr->wr_rx_buf_v2 and add_llc was not used after the free. Reproduced on an unpatched tree over rxe, with KASAN, kasan_multi_shot and a link forced to max_recv_sge == 1: the entry is freed and read by the same call, and the freeing frame is smc_llc_srv_add_link() itself. [ 2.523161] BUG: KASAN: slab-use-after-free in smc_llc_save_add_link_rkeys+0x333/0x350 [ 2.523499] Read of size 2 at addr ffff8880052194de by task kworker/0:1/11 [ 2.523789] [ 2.523862] CPU: 0 UID: 0 PID: 11 Comm: kworker/0:1 Not tainted 7.2.0-rc5-p0-g2c9dd296545d #35 PREEMPT(lazy) [ 2.523865] Hardware name: QEMU Ubuntu 24.04 PC v2 (i440FX + PIIX, arch_caps fix, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 [ 2.523866] Workqueue: smc_hs_wq smc_listen_work [ 2.523869] Call Trace: [ 2.523870] <TASK> [ 2.523871] dump_stack_lvl+0x53/0x70 [ 2.523872] print_report+0xd0/0x630 [ 2.523874] ? __pfx__raw_spin_lock_irqsave+0x10/0x10 [ 2.523876] ? smc_llc_save_add_link_rkeys+0x333/0x350 [ 2.523878] kasan_report+0xce/0x100 [ 2.523879] ? smc_llc_save_add_link_rkeys+0x333/0x350 [ 2.523881] smc_llc_save_add_link_rkeys+0x333/0x350 [ 2.523883] ? smcr_buf_reg_lgr+0x2a4/0x660 [ 2.523885] smc_llc_srv_add_link+0xaa2/0x1e50 [ 2.523888] ? _printk+0xba/0xf0 [ 2.523897] ? __pfx_smc_llc_srv_add_link+0x10/0x10 [ 2.523899] ? down_write+0xb0/0x130 [ 2.523903] ? __pfx_down_write+0x10/0x10 [ 2.523905] smc_listen_work+0x489e/0x4d00 [ 2.523907] ? kmem_cache_free+0x1c6/0x3a0 [ 2.523911] ? __pfx_smc_listen_work+0x10/0x10 [ 2.523913] ? release_sock+0x148/0x1d0 [ 2.523915] ? smc_tcp_listen_work+0xb4f/0xfc0 [ 2.523917] ? _raw_spin_lock_irq+0x80/0xe0 [ 2.523918] ? __pfx__raw_spin_lock_irq+0x10/0x10 [ 2.523920] process_one_work+0x633/0x1030 [ 2.523922] ? assign_work+0x11d/0x370 [ 2.523924] worker_thread+0x45b/0xd10 [ 2.523926] ? __pfx_worker_thread+0x10/0x10 [ 2.523928] ? __pfx_worker_thread+0x10/0x10 [ 2.523929] kthread+0x2c6/0x3b0 [ 2.523931] ? recalc_sigpending+0x15c/0x1e0 [ 2.523934] ? __pfx_kthread+0x10/0x10 [ 2.523935] ret_from_fork+0x36e/0x5a0 [ 2.523937] ? __pfx_ret_from_fork+0x10/0x10 [ 2.523938] ? __switch_to+0x572/0xdd0 [ 2.523943] ? __pfx_kthread+0x10/0x10 [ 2.523944] ret_from_fork_asm+0x1a/0x30 [ 2.523947] </TASK> [ 2.523948] [ 2.531253] Allocated by task 48: [ 2.531399] kasan_save_stack+0x33/0x60 [ 2.531570] kasan_save_track+0x14/0x30 [ 2.531737] __kasan_kmalloc+0x8f/0xa0 [ 2.531905] __kmalloc_cache_noprof+0x158/0x370 [ 2.532100] smc_llc_enqueue+0x72/0x560 [ 2.532268] smc_wr_rx_tasklet_fn+0x474/0xa80 [ 2.532491] tasklet_action_common+0x20f/0x8a0 [ 2.532714] handle_softirqs+0x18e/0x590 [ 2.532886] do_softirq+0x3b/0x60 [ 2.533036] __local_bh_enable_ip+0x61/0x70 [ 2.533221] __alloc_skb+0x732/0x890 [ 2.533384] rxe_init_packet+0x16b/0x4f0 [ 2.533567] prepare_ack_packet+0xb8/0x830 [ 2.533760] rxe_receiver+0x495/0x96e0 [ 2.533933] do_work+0x144/0x470 [ 2 ---truncated--- | 19 Oct |
| CVE-2026-80976 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: seg6: reset IP6CB after IPv6 decapsulation decap_and_validate() pulls the outer SRv6 headers and makes the inner packet the skb network header. The IPv6 control block still contains values collected while parsing the outer packet, including nhoff and extension-header flags. End.DX6 and End.DT6 route the inner IPv6 packet directly to the IPv6 input path. An unprivileged user can reach End.DT6 from a user and net namespace by installing a local SID and injecting an outer packet with Hop-by-Hop and Destination Options headers followed by an SRH and a minimal inner IPv6 packet. The outer extension headers leave a large nhoff in IP6CB. After decapsulation, ip6_protocol_deliver_rcu() uses that stale offset on the inner packet and reads beyond the skb head. KASAN reports: BUG: KASAN: slab-out-of-bounds in ip6_protocol_deliver_rcu ip6_protocol_deliver_rcu+0x1118/0x1450 ip6_input_finish+0x11b/0x240 seg6_local_input_core+0xed/0x2e0 lwtunnel_input+0x1e9/0x4e0 ipv6_rthdr_rcv+0x525f/0x6c50 ip6_protocol_deliver_rcu+0xcb7/0x1450 Before clearing IP6CB for an inner IPv6 packet, save its incoming interface index and L3 slave state. Restore both after the clear and set nhoff to the inner IPv6 base-header nexthdr field. Use IP6CB(skb)->iif rather than skb->skb_iif because VRF processing can replace skb_iif with the L3 master while IP6CB keeps the receiving interface. Preserve IP6SKB_L3SLAVE for the same reason. | 19 Oct |
| CVE-2025-40261 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: nvme: nvme-fc: Ensure ->ioerr_work is cancelled in nvme_fc_delete_ctrl() nvme_fc_delete_assocation() waits for pending I/O to complete before returning, and an error can cause ->ioerr_work to be queued after cancel_work_sync() had been called. Move the call to cancel_work_sync() to be after nvme_fc_delete_association() to ensure ->ioerr_work is not running when the nvme_fc_ctrl object is freed. Otherwise the following can occur: [ 1135.911754] list_del corruption, ff2d24c8093f31f8->next is NULL [ 1135.917705] ------------[ cut here ]------------ [ 1135.922336] kernel BUG at lib/list_debug.c:52! [ 1135.926784] Oops: invalid opcode: 0000 [#1] SMP NOPTI [ 1135.931851] CPU: 48 UID: 0 PID: 726 Comm: kworker/u449:23 Kdump: loaded Not tainted 6.12.0 #1 PREEMPT(voluntary) [ 1135.943490] Hardware name: Dell Inc. PowerEdge R660/0HGTK9, BIOS 2.5.4 01/16/2025 [ 1135.950969] Workqueue: 0x0 (nvme-wq) [ 1135.954673] RIP: 0010:__list_del_entry_valid_or_report.cold+0xf/0x6f [ 1135.961041] Code: c7 c7 98 68 72 94 e8 26 45 fe ff 0f 0b 48 c7 c7 70 68 72 94 e8 18 45 fe ff 0f 0b 48 89 fe 48 c7 c7 80 69 72 94 e8 07 45 fe ff <0f> 0b 48 89 d1 48 c7 c7 a0 6a 72 94 48 89 c2 e8 f3 44 fe ff 0f 0b [ 1135.979788] RSP: 0018:ff579b19482d3e50 EFLAGS: 00010046 [ 1135.985015] RAX: 0000000000000033 RBX: ff2d24c8093f31f0 RCX: 0000000000000000 [ 1135.992148] RDX: 0000000000000000 RSI: ff2d24d6bfa1d0c0 RDI: ff2d24d6bfa1d0c0 [ 1135.999278] RBP: ff2d24c8093f31f8 R08: 0000000000000000 R09: ffffffff951e2b08 [ 1136.006413] R10: ffffffff95122ac8 R11: 0000000000000003 R12: ff2d24c78697c100 [ 1136.013546] R13: fffffffffffffff8 R14: 0000000000000000 R15: ff2d24c78697c0c0 [ 1136.020677] FS: 0000000000000000(0000) GS:ff2d24d6bfa00000(0000) knlGS:0000000000000000 [ 1136.028765] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 1136.034510] CR2: 00007fd207f90b80 CR3: 000000163ea22003 CR4: 0000000000f73ef0 [ 1136.041641] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 1136.048776] DR3: 0000000000000000 DR6: 00000000fffe07f0 DR7: 0000000000000400 [ 1136.055910] PKRU: 55555554 [ 1136.058623] Call Trace: [ 1136.061074] <TASK> [ 1136.063179] ? show_trace_log_lvl+0x1b0/0x2f0 [ 1136.067540] ? show_trace_log_lvl+0x1b0/0x2f0 [ 1136.071898] ? move_linked_works+0x4a/0xa0 [ 1136.075998] ? __list_del_entry_valid_or_report.cold+0xf/0x6f [ 1136.081744] ? __die_body.cold+0x8/0x12 [ 1136.085584] ? die+0x2e/0x50 [ 1136.088469] ? do_trap+0xca/0x110 [ 1136.091789] ? do_error_trap+0x65/0x80 [ 1136.095543] ? __list_del_entry_valid_or_report.cold+0xf/0x6f [ 1136.101289] ? exc_invalid_op+0x50/0x70 [ 1136.105127] ? __list_del_entry_valid_or_report.cold+0xf/0x6f [ 1136.110874] ? asm_exc_invalid_op+0x1a/0x20 [ 1136.115059] ? __list_del_entry_valid_or_report.cold+0xf/0x6f [ 1136.120806] move_linked_works+0x4a/0xa0 [ 1136.124733] worker_thread+0x216/0x3a0 [ 1136.128485] ? __pfx_worker_thread+0x10/0x10 [ 1136.132758] kthread+0xfa/0x240 [ 1136.135904] ? __pfx_kthread+0x10/0x10 [ 1136.139657] ret_from_fork+0x31/0x50 [ 1136.143236] ? __pfx_kthread+0x10/0x10 [ 1136.146988] ret_from_fork_asm+0x1a/0x30 [ 1136.150915] </TASK> | 18 Oct |
| CVE-2026-80681 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: vxlan: re-fetch eth header after route_shortcircuit() Before route_shortcircuit(), the eth header pointer is cached from eth_hdr(skb). Inside route_shortcircuit(), pskb_may_pull() can be called, which may reallocate skb->head. In this case, returning to vxlan_xmit() leaves the cached eth pointer pointing to freed memory, leading to a use-after-free when dereferencing eth->h_dest. Fix this by updating eth = eth_hdr(skb) after calling route_shortcircuit(). | 16 Oct |
| CVE-2026-80630 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: net/sched: sch_fq_codel: Do not call qdisc_tree_reduce_backlog during peek before restoring qlen Whenever fq_codel drops packets during peek, it calls qdisc_tree_reduce_backlog. An issue arises because it calls qdisc_tree_reduce_backlog before it reincrements the qlen. If qlen drops to zero, but peek returns an skb, the parent's qlen_notify callback will be executed even though fq_codel still has 1 packet on the queue and, thus, will mistakenly deactivate the parent's class causing issues like a recent report [1] and a wild memory access in qfq: [ 29.371146][ T360] Oops: general protection fault, probably for non-canonical address 0xfbd59c0000000024: 0000 [#1] SMP KASAN NOPTI [ 29.371666][ T360] KASAN: maybe wild-memory-access in range [0xdead000000000120-0xdead000000000127] [ 29.371987][ T360] CPU: 6 UID: 0 PID: 360 Comm: tc Not tainted 7.1.0-rc5-00285-gc530e5b2dbc6-dirty #82 PREEMPT(full) [ 29.372384][ T360] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011 [ 29.372620][ T360] RIP: 0010:qfq_deactivate_agg (include/linux/list.h:1029 (discriminator 2) include/linux/list.h:1043 (discriminator 2) net/sched/sch_qfq.c:1369 (discriminator 2) net/sched/sch_qfq.c:1395 (discriminator 2)) sch_qfq [ 29.373544][ T360] RSP: 0018:ffff888102417370 EFLAGS: 00010216 [ 29.373800][ T360] RAX: 0000000000000000 RBX: ffff88811224d568 RCX: dffffc0000000000 [ 29.374079][ T360] RDX: 1ffff11021fe1543 RSI: ffff88810ff0aa00 RDI: dffffc0000000000 [ 29.374368][ T360] RBP: ffff88811224c280 R08: dead000000000122 R09: 1bd5a00000000024 [ 29.374649][ T360] R10: fffffbfff7940329 R11: fffffbfff7940329 R12: 0000000000000000 [ 29.374926][ T360] R13: dead000000000100 R14: ffff88811224d580 R15: ffff88811224d578 [ 29.375207][ T360] FS: 00007f5b794e5780(0000) GS:ffff88815d1e9000(0000) knlGS:0000000000000000 [ 29.375545][ T360] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 29.375823][ T360] CR2: 000055ffb091f000 CR3: 000000010a305000 CR4: 0000000000750ef0 [ 29.376103][ T360] PKRU: 55555554 [ 29.376258][ T360] Call Trace: [ 29.376401][ T360] <TASK> ... [ 29.376885][ T360] qfq_reset_qdisc (net/sched/sch_qfq.c:357 net/sched/sch_qfq.c:1487) sch_qfq [ 29.377074][ T360] qdisc_reset (net/sched/sch_generic.c:1057) [ 29.377414][ T360] __qdisc_destroy (net/sched/sch_generic.c:1096) [ 29.377600][ T360] qdisc_graft (net/sched/sch_api.c:1062 net/sched/sch_api.c:1053 net/sched/sch_api.c:1159) [ 29.378593][ T360] tc_get_qdisc (net/sched/sch_api.c:1528 net/sched/sch_api.c:1556) Fix this by only calling qdisc_tree_reduce_backlog in peek after the qlen is restored. [1] http://lore.kernel.org/netdev/CAN2cbVe79oj0O9==m4+4x3v+O+qzRagA=2=wkrp9i9=CqYvyZA@mail.gmail.com/ | 16 Oct |
| CVE-2026-80609 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: qede: fix out-of-bounds check for cqe->len_list[] Move index check before element access. | 16 Oct |
| CVE-2026-80561 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: libceph: fix multiple unsafe decodes in decode_locker() decode_locker() in cls_lock_client.c contains three unsafe decode operations that allow a malicious or compromised OSD to trigger slab-out-of-bounds reads: 1. ceph_decode_copy() at the locker_id_t name field has no preceding bounds check. With p == end after ceph_start_decoding() accepts struct_len=0, this reads sizeof(ceph_entity_name) = 9 bytes past the validated buffer boundary. 2. *p += sizeof(struct ceph_timespec) after the locker_info_t header is an unchecked pointer advance. A malicious OSD can position p past end, causing all subsequent _safe checks to pass against a bogus boundary. 3. len = ceph_decode_32(p) has no preceding bounds check, and the immediately following *p += len is uncapped. A malicious OSD can send len=0xffffffff, advancing p gigabytes past end and escaping the decode window entirely. Fix all three by replacing bare operations with their safe variants: ceph_decode_copy -> ceph_decode_copy_safe *p += sizeof(...) -> ceph_decode_skip_n ceph_decode_32(p) -> ceph_decode_32_safe *p += len -> ceph_decode_skip_n A new label is added to return -EINVAL on any bounds violation. -EINVAL is appropriate here: the data received from the OSD is structurally malformed, which is an invalid argument to the decode contract regardless of whether the caller or the wire is at fault. Attacker model: a malicious or compromised OSD in a multi-tenant Ceph deployment can trigger this against any kernel client that issues the lock.get_info class method (e.g. during RBD exclusive lock acquisition) without any further privileges beyond OSD session establishment. [ idryomov: use ceph_decode_skip_string() to skip description, trim changelog ] | 16 Oct |
| CVE-2026-80558 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: libceph: Avoid using invalid osd indices from primary_temp A corrupted osdmap received from a Ceph monitor or OSD may contain osd indices in its pg_temp, primary_temp, pg_upmap, and pg_upmap_items parts that don't exist, i.e., that are greater than max_osd or smaller than CEPH_HOMELESS_OSD (-1). These indices are used to create the up and acting set in ceph_pg_to_up_acting_osds(), called from calc_target(). While most of these osd indices are checked, the one from primary_temp is not. Subsequently, this may lead to calc_target() returning this (potentially invalid) index as target osd for a (linger) request. Because the osd_state, osd_weight, and osd_addr arrays only contain max_osd entries (with indices 0 to max_osd -1), this leads to out-of-bounds accesses when trying to read values from these arrays. This patch fixes the issue by adding a check to get_temp_osds(), so that only valid osd indices from primary_temp are used, and it falls back to using the primary from pg_temp or the up set if it is invalid. [ idryomov: changelog ] | 16 Oct |
| CVE-2026-80557 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: libceph: fix OOB read in decode_watchers() via missing bounds check ceph_start_decoding() validates that struct_len bytes remain in the buffer after the encoding header, but accepts struct_len=0 as valid: ceph_decode_need(p, end, 0, bad) always passes. When a malicious or compromised OSD sends an obj_list_watch_response_t reply with struct_len=0, ceph_start_decoding() returns success with p == end, leaving zero bytes guaranteed for subsequent reads. The immediately following ceph_decode_32(p) in decode_watchers() has no preceding bounds check. With p == end this is a 4-byte read past the validated buffer boundary. The garbage value is then passed directly to kzalloc_objs() as the watcher count. The sibling function decode_watcher() already uses the safe variants (ceph_decode_copy_safe, ceph_decode_64_safe, ceph_decode_skip_32) after its own ceph_start_decoding() call. decode_watchers() is the only site that uses the bare variant, confirming an oversight. Fix by replacing ceph_decode_32(p) with ceph_decode_32_safe(p, end, *num_watchers, bad), consistent with the established pattern. Attacker model: a malicious or compromised OSD in a multi-tenant Ceph deployment (e.g. cloud) can trigger this against any kernel client that calls CEPH_OSD_OP_LIST_WATCHERS, without any further privileges beyond OSD session establishment. [ idryomov: trim changelog ] | 16 Oct |
| CVE-2026-80528 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: ceph: avoid fs reclaim while using current->journal_info handle_reply() stores a `ceph_mds_request` pointer in `current->journal_info` while filling the inode and dentry cache from an MDS reply. An allocation in this section can enter direct reclaim and prune dentries from another filesystem. If this dirties an ext4 inode, ext4 starts a JBD2 transaction. JBD2 interprets the Ceph request in `current->journal_info` as a journal handle and dereferences the request's `r_tid` as `h_transaction`, causing a kernel crash, e.g.: Unable to handle kernel paging request at virtual address 00000000077b4818 [...] Internal error: Oops: 0000000096000004 [#1] SMP Modules linked in: CPU: 6 UID: 0 PID: 2699135 Comm: kworker/6:3 Tainted: G W 6.18.38-i3 #1113 NONE [...] Workqueue: ceph-msgr ceph_con_workfn pstate: 80400009 (Nzcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : jbd2__journal_start+0x2c/0x208 lr : __ext4_journal_start_sb+0x100/0x178 [...] Call trace: jbd2__journal_start+0x2c/0x208 (P) __ext4_journal_start_sb+0x100/0x178 ext4_dirty_inode+0x3c/0x90 __mark_inode_dirty+0x58/0x400 iput.part.0+0x2b0/0x370 iput+0x18/0x30 dentry_unlink_inode+0xc0/0x158 __dentry_kill+0x80/0x250 shrink_dentry_list+0x90/0x130 prune_dcache_sb+0x60/0x98 super_cache_scan+0xe8/0x190 do_shrink_slab+0x174/0x388 shrink_slab+0xd8/0x4c0 shrink_node+0x31c/0x908 do_try_to_free_pages+0xd0/0x508 try_to_free_pages+0x11c/0x238 __alloc_frozen_pages_noprof+0x4d0/0xdd0 __folio_alloc_noprof+0x18/0x70 __filemap_get_folio+0x248/0x440 ceph_readdir_prepopulate+0x570/0x9e8 mds_dispatch+0x1424/0x1ba0 ceph_con_process_message+0x74/0xa0 ceph_con_v1_try_read+0x3a0/0x1510 ceph_con_workfn+0x260/0x460 Enter a scoped NOFS allocation context and leave it after clearing `journal_info`. This prevents filesystem reclaim from recursing into another filesystem while the field contains Ceph-private data. | 16 Oct |
| CVE-2026-74746 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: netfilter: flowtable: publish GC-visible tuple last nf_flow_table_iterate() only treats original-direction tuple nodes as owning entries. Publishing the original node first lets GC observe and free a flow while flow_offload_add() is still inserting the reply node. Publish the reply node first and the original node last so GC never sees a partially installed flow. KASAN can trigger slab-use-after-free read and write reports in the flowtable/rhashtable path (rht_deferred_worker, jhash, flow_offload_del, flow_offload_lookup, etc.). | 16 Oct |
| CVE-2026-74744 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: ipvlan: inherit needed_headroom and needed_tailroom from phy_dev ipvlan devices inherit hard_header_len from phy_dev during ipvlan_init(), but leave needed_headroom and needed_tailroom set to 0. When the underlying phy_dev (or stacked lower device) requires extra headroom or tailroom for headers/trailers (e.g. macsec, ipsec, wireguard, tunnels, or veth with rx headroom), upper layers calculating packet headroom and tailroom fail to reserve sufficient space. This can result in reallocation overhead, skb headroom underflows, or KASAN slab-use-after-free crashes when dev_hard_header() / ipvlan_hard_header() prepends header data or when lower devices append tailroom. Fix this by: 1. Inheriting needed_headroom and needed_tailroom from phy_dev in ipvlan_init(). 2. Propagating needed_headroom and needed_tailroom updates to attached ipvlans in ipvlan_device_event() when receiving NETDEV_FEAT_CHANGE events. | 16 Oct |
| CVE-2026-74743 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: macvlan: inherit needed_headroom and needed_tailroom from lowerdev macvlan devices inherit hard_header_len from lowerdev during macvlan_init(), but leave needed_headroom and needed_tailroom set to 0. When the underlying lowerdev requires extra headroom or tailroom for headers/trailers (e.g. macsec, ipsec, wireguard, tunnels, or veth with rx headroom), upper layers calculating packet headroom and tailroom fail to reserve sufficient space. This can result in reallocation overhead, skb headroom underflows, or KASAN slab-use-after-free crashes when dev_hard_header() / macvlan_hard_header() prepends header data or when lower devices append tailroom. Fix this by: 1. Inheriting needed_headroom and needed_tailroom from lowerdev in macvlan_init(). 2. Propagating needed_headroom and needed_tailroom updates to attached macvlans in macvlan_device_event() when receiving NETDEV_FEAT_CHANGE events. | 16 Oct |
| CVE-2026-74730 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: NFS: Pin the 'struct nfs_server' during a FREE_STATEID call Dan Aloni reports that he was able to hit a use-after-free bug if a FREE_STATEID operation gets delayed for whatever reason. Fix this by bumping the refcount of the 'struct nfs_server' object for the duration of the FREE_STATEID so it doesn't get cleaned up from underneath us while operations are still in flight. | 16 Oct |
| CVE-2026-74688 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: sctp: clear control chunk transport if it is being removed sctp_make_heartbeat_ack() caches the destination transport in chunk->transport without taking a reference. When src_out_of_asoc_ok is enabled, the HEARTBEAT ACK may remain queued on control_chunk_list instead of being transmitted immediately. If the peer transport is removed while the chunk is still queued, sctp_assoc_rm_peer() drops the transport and schedules it for RCU freeing, but only clears cached transport pointers in out_chunk_list. The queued control chunk therefore retains a dangling transport pointer. Once an ASCONF_ACK clears the suppression and the queued control chunk is transmitted, SCTP dereferences the stale transport pointer, leading to a use-after-free. Fix this by also clearing chunk->transport for queued control chunks in control_chunk_list when removing the transport. | 16 Oct |
| CVE-2026-74669 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: ipvs: clear IPv4 options after rebasing tunnel ICMP errors ip_vs_in_icmp() rebases an skb from the outer ICMP packet to the quoted original request before passing it to icmp_send(). However, IPCB(skb)->opt still describes the outer IPv4 header. A timestamp option in the outer header can therefore leave an offset that points into the quoted transport header after the rebase. __ip_options_echo() treats a byte at that stale location as the option length and copies it into the fixed-size option storage on the __icmp_send() stack, causing a stack out-of-bounds write. Clear the stale option metadata after resetting the network header. Keep the remaining control block fields, including the ingress interface used by the ICMP response path. | 16 Oct |
| CVE-2026-74662 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: inet: frags: publish queues before arming timer inet_frag_create() arms the fragment queue timer before inserting the queue into the fqdir rhashtable. If the namespace fragment timeout is zero or negative, the timer can run before the queue is published. The timer callback then marks the queue complete, tries to remove a node that is not in the hash table yet, and drops the anticipated hash reference. Creation can subsequently publish the completed queue without restoring that reference, leaving a stale hash node after the caller drops the remaining reference. Publish the queue first and arm the timer while holding the queue lock. This makes timer expiry wait until the queue is visible in the hash table, so inet_frag_kill() can remove the node and balance the hash reference. | 16 Oct |
| CVE-2026-74617 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: dibs: initialise dibs->lock in dibs_dev_alloc() dibs->lock is initialised by dibs_dev_add(), but a dibs device can already take interrupts before that call: ism_probe() runs ism_dev_init(), and hence request_irq(), before it calls dibs_dev_add(). No client can have registered a dmb at that point, so no dmb interrupt can occur, but a GID event interrupt can, and ism_handle_irq() takes dibs->lock unconditionally on entry, before it inspects anything else. Initialise the lock in dibs_dev_alloc() instead, so that it is valid as soon as a driver can publish the device to its interrupt handler. | 16 Oct |
| CVE-2026-74616 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: xdp: reject clones that overrun skb_shared_info tailroom xdpf_clone() clones broadcast copies into a single page and sets frame_sz to PAGE_SIZE. __xdp_build_skb_from_frame() later treats that page like a normal XDP frame and expects the usual skb_shared_info tailroom at the end of the buffer. The current check only rejects frames whose linear xdp_frame header, headroom, and packet data exceed PAGE_SIZE. A source frame backed by a larger allocation can still satisfy that check while extending into the clone's required shared-info area. When such a clone is converted back into an skb, build_skb_around() places skb_shared_info over live packet bytes and later writes can corrupt XDP return metadata. Reject clones unless their linear area fits inside SKB_WITH_OVERHEAD(PAGE_SIZE), matching the tailroom requirement already enforced by the XDP-to-skb conversion path. | 16 Oct |
| CVE-2026-74597 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: ip6_tunnel: clear skb2->cb[] in ip6ip6_err() ip6ip6_err() clones an outer IPv6 ICMP error skb, pulls it to the quoted inner IPv6 packet, and then passes the clone to icmpv6_send(). The clone still carries the outer packet's inet6_skb_parm in skb->cb. If the outer packet had a Home Address Option, IP6CB(skb2)->dsthao remains non-zero after skb_pull(). icmpv6_send() later calls mip6_addr_swap(), which uses that stale dsthao offset against the quoted inner packet. A malformed inner destination-options header can then make the HAO lookup and address swap run past the end of the quoted packet and corrupt skb_shared_info. Clear skb2->cb[] before pulling the quoted inner IPv6 packet so the reply path does not reuse metadata left by the outer IPv6 stack. | 16 Oct |
| CVE-2026-74588 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: sctp: keep chunk->transport in step with the list it is queued on __sctp_outq_flush_rtx() moves a gap-acked chunk onto another transport's transmitted list without updating chunk->transport: if (chunk->tsn_gap_acked) { list_move_tail(&chunk->transmitted_list, &transport->transmitted); continue; } The chunk then sits on a live transport's list while chunk->transport still names a different one. If that transport is removed - sctp_assoc_rm_peer() from an ASCONF Delete-IP - sctp_transport_free() RCU-frees it and the chunk is left with a dangling pointer. sctp_assoc_rm_peer() scrubs peer->transmitted and asoc->outqueue.out_chunk_list, but the chunk is on neither. The pointer is not followed while tsn_gap_acked is set. A SACK that reneges on the TSN clears the flag, and the next SACK reaches tchunk->transport->flight_size -= sctp_data_size(tchunk); inside the freed transport. KASAN reports a slab-use-after-free read in sctp_check_transmitted(), freed from sctp_assoc_rm_peer(). Both the removal and the SACKs come from the association peer. Set chunk->transport at the move. The ordinary resend path needs nothing: it reaches its list_move_tail() only after sctp_packet_append_chunk() returned SCTP_XMIT_OK, and __sctp_packet_append_chunk() has rebound the chunk by then. Discovered by XBOW, triaged by Baul Lee <[email protected]> | 16 Oct |
| CVE-2026-74587 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: sctp: fix use-after-free of cached ASCONF chunk addip_last_asconf caches the outstanding outbound ASCONF chunk. The normal ASCONF-ACK completion path releases the chunk and clears the pointer. However, sctp_asconf_queue_teardown() releases the cached chunk without clearing addip_last_asconf. During peer restart handling, sctp_sf_do_dupcook_a() queues SCTP_CMD_PURGE_ASCONF_QUEUE, which invokes sctp_asconf_queue_teardown() while the association remains alive and leaves the pointer dangling. A delayed authenticated ASCONF-ACK can then reach sctp_sf_do_asconf_ack(), which accesses the stale chunk and passes it to sctp_process_asconf_ack(), causing a use-after-free and a second release. Clearing the pointer exposes a race with T4 expiry. Peer restart handling queues the timer stop before the purge, but SCTP_CMD_TIMER_STOP uses timer_delete(), which does not wait for a callback already running on another CPU. Such a callback can reach sctp_sf_t4_timer_expire() after the purge and dereference NULL. Clear addip_last_asconf after releasing the cached chunk, and make sctp_sf_t4_timer_expire() consume a stale T4 expiry if no outstanding ASCONF remains. | 16 Oct |
| CVE-2026-74495 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: igbvf: Fix leak in TX DMA error cleanup If an error is encountered while mapping TX buffers, the driver should unmap any buffers already mapped for that skb. Because count is incremented before each frag mapping, it will always match the correct number of unmappings needed when dma_error is reached. Decrementing count before the while loop in dma_error causes an off-by-one error. If any mapping was successful before an unsuccessful mapping, exactly one DMA mapping (the head) would leak. This bug was introduced by a 2010 fix for an endless loop in dma_error. All other affected drivers have already been fixed. | 16 Oct |
| CVE-2026-74493 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: net/smc: fix socket use-after-free during link group termination __smc_lgr_terminate() drops conns_lock after finding a connection in lgr->conns_all, but before taking a reference on its socket. The connection is embedded in the socket, and its registration reference protects it only while the connection remains in the tree. A concurrent close can unregister the connection and drop that reference, freeing the socket before the termination worker reaches sock_hold(). The race is reachable when close overlaps link group termination. Local stress testing reproduced the use-after-free and KASAN reported: BUG: KASAN: slab-use-after-free in __smc_lgr_terminate.part.0 [smc] Write of size 4 by task kworker/3:3 Workqueue: events smc_lgr_terminate_work [smc] __smc_lgr_terminate.part.0 [smc] The socket was allocated by smc_create(), freed through slab_free_after_rcu_debug(), and was followed by: refcount_t: addition on 0; use-after-free. __smc_lgr_terminate.part.0 [smc] Take the socket reference while conns_lock still protects the tree entry. The unregister path then cannot drop the last reference until termination has finished using the socket. | 16 Oct |
| CVE-2026-74480 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: net: bridge: stop fast-leave after deleting a port group br_multicast_leave_group() iterates mp->ports with pp = &p->next in its fast-leave path. After br_multicast_del_pg() removes p, continuing the loop advances pp through the deleted entry. If multicast-to-unicast was enabled, the bridge can hold multiple port groups for the same port and group with different source MAC addresses. Once multicast-to-unicast is disabled, br_port_group_equal() matches those entries by port only. A fast leave can then delete one entry and continue from its stale next pointer, leaving mp->ports pointing at a deleted port group. Fast leave only needs to remove one matching port group. Break after br_multicast_del_pg() so the loop stops before dereferencing the removed entry. | 16 Oct |
| CVE-2026-74473 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: vxlan: use pskb_network_may_pull() in route_shortcircuit() route_shortcircuit() currently calls pskb_may_pull(skb, sizeof(struct iphdr)) (or ipv6hdr), which checks if bytes are available starting from skb->data. However, in vxlan_xmit(), skb->data points to the MAC header, so skb_network_offset(skb) is ETH_HLEN (14 bytes). Using pskb_may_pull(skb, 20) only checks 20 bytes from skb->data (which is 14 bytes MAC header + 6 bytes of IP header), leaving the rest of the IP header potentially un-pulled in non-linear frags. Subsequent dereferences of ip_hdr(skb)->daddr can read beyond the pulled linear buffer length. Fix this by using pskb_network_may_pull(), which adds skb_network_offset(skb) to the length check to ensure the full network header is present in the linear buffer. | 16 Oct |
| CVE-2026-74427 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: afs: Fix netns teardown to cancel the preallocation charger Fix the teardown of an afs network namespace to make sure it cancels the work item that keeps the preallocated rxrpc call/conn/peer queue charged before incoming calls are disabled (i.e. listen 0). Also, if net->live is false because the afs netns is being deleted, make afs_charge_preallocation() skip charging and make afs_rx_new_call() avoid requeuing the charger. (This was found by AI review). | 16 Oct |
| CVE-2026-74398 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: ipv6: addrconf: bail out of dad_failure when state is no longer POSTDAD addrconf_dad_failure() transitions ifp->state from DAD to POSTDAD via addrconf_dad_end(), which drops ifp->lock on return. The lock is re-acquired after net_info_ratelimited(). A concurrent ipv6_del_addr() can take the lock in that window, set ifp->state to DEAD and run list_del_rcu(&ifp->if_list). addrconf_dad_failure() then overwrites DEAD with ERRDAD at errdad: and schedules a new dad_work. The work calls ipv6_del_addr() again, hitting the already-poisoned list entry: general protection fault: 0000 [#1] SMP NOPTI CPU: 4 PID: 217 Comm: kworker/4:1 Workqueue: ipv6_addrconf addrconf_dad_work RIP: 0010:ipv6_del_addr+0xe9/0x280 RAX: dead000000000122 Call Trace: addrconf_dad_stop+0x113/0x140 addrconf_dad_work+0x28c/0x430 process_one_work+0x1eb/0x3b0 worker_thread+0x4d/0x400 kthread+0x104/0x140 ret_from_fork+0x35/0x40 Fold the addrconf_dad_end() logic into addrconf_dad_failure() under a single ifp->lock critical section. The STABLE_PRIVACY branch temporarily drops ifp->lock around address regeneration, so at lock_errdad: verify the state is still POSTDAD before transitioning to ERRDAD; bail out otherwise to avoid overwriting a state set by another path while the lock was released. | 16 Oct |
| CVE-2026-74394 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: RDMA/srpt: fix integer overflow in immediate data length check imm_buf->len is a user-controlled uint32_t received from the network. Adding it to imm_data_offset without overflow checking allows a malicious initiator to send len=0xFFFFFFFF, causing req_size to wrap around to a small value, bypassing the bounds check, and subsequently passing a ~4GB length to sg_init_one(). Use check_add_overflow() to detect wrapping before the comparison. | 16 Oct |
| CVE-2026-74384 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: nvme-multipath: fix flex array size in struct nvme_ns_head struct nvme_ns_head contains a flexible array member, current_path[], which is indexed using the NUMA node ID: head->current_path[numa_node_id()] The structure is currently allocated as: size = sizeof(struct nvme_ns_head) + (num_possible_nodes() * sizeof(struct nvme_ns *)); head = kzalloc(size, GFP_KERNEL); This allocation assumes that NUMA node IDs are sequential and densely packed from 0 .. num_possible_nodes() - 1. While this assumption holds on many systems, it is not always true on some architectures such as powerpc. On some powerpc systems, NUMA node IDs can be sparse. For example: NUMA: NUMA node(s): 6 NUMA node0 CPU(s): 80-159 NUMA node8 CPU(s): 0-79 NUMA node252 CPU(s): NUMA node253 CPU(s): NUMA node254 CPU(s): NUMA node255 CPU(s): That is, the possible/online NUMA node IDs are: 0, 8, 252, 253, 254, 255 In this case: num_possible_nodes() = 6 So memory is allocated for only 6 entries in current_path[]. However, the array is later indexed using the actual NUMA node ID. As a result, accesses such as: head->current_path[8] or head->current_path[252] goes out of bounds, leading to the following KASAN splat: ================================================================== BUG: KASAN: slab-out-of-bounds in nvme_mpath_revalidate_paths+0x22c/0x290 [nvme_core] Write of size 8 at addr c00020003bda35b8 by task kworker/u641:2/1997 CPU: 1 UID: 0 PID: 1997 Comm: kworker/u641:2 Not tainted 7.1.0-rc5-dirty #14 PREEMPT(lazy) Hardware name: 8335-GTH POWER9 0x4e1202 opal:skiboot-v6.5.3-35-g1851b2a06 PowerNV Workqueue: async async_run_entry_fn Call Trace: [c000200037fa7510] [c0000000021c23d4] dump_stack_lvl+0x88/0xdc (unreliable) [c000200037fa7540] [c0000000009fda90] print_report+0x22c/0x67c [c000200037fa7630] [c0000000009fd508] kasan_report+0x108/0x220 [c000200037fa7740] [c0000000009fff48] __asan_store8+0xe8/0x120 [c000200037fa7760] [c008000018e76474] nvme_mpath_revalidate_paths+0x22c/0x290 [nvme_core] [c000200037fa7800] [c008000018e6556c] nvme_update_ns_info+0x4a4/0x5e0 [nvme_core] [c000200037fa7a50] [c008000018e66270] nvme_alloc_ns+0x6d8/0x1a70 [nvme_core] [c000200037fa7c20] [c008000018e679fc] nvme_scan_ns+0x3f4/0x630 [nvme_core] [c000200037fa7d10] [c00000000031f22c] async_run_entry_fn+0x9c/0x3a0 [c000200037fa7db0] [c0000000002fa544] process_one_work+0x414/0xa10 [c000200037fa7ec0] [c0000000002fbf00] worker_thread+0x320/0x640 [c000200037fa7f80] [c00000000030d0f8] kthread+0x278/0x290 [c000200037fa7fe0] [c00000000000ded8] start_kernel_thread+0x14/0x18 Allocated by task 1997 on cpu 1 at 35.928317s: The buggy address belongs to the object at c00020003bda3000 which belongs to the cache kmalloc-rnd-15-2k of size 2048 The buggy address is located 16 bytes to the right of allocated 1448-byte region [c00020003bda3000, c00020003bda35a8) The buggy address belongs to the physical page: Memory state around the buggy address: c00020003bda3480: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c00020003bda3500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 >c00020003bda3580: 00 00 00 00 00 fc fc fc fc fc fc fc fc fc fc fc ^ c00020003bda3600: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc c00020003bda3680: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ================================================================== Fix this by allocating the flexible array using nr_node_ids instead of num_possible_nodes(). Since nr_node_ids represents the maximum possible NUMA node IDs, indexing current_path[] using numa_node_id() becomes safe even on systems with sparse node IDs. | 16 Oct |
| CVE-2026-74376 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: md/raid10: reset read_slot when reusing r10bio for discard put_all_bios() always drops devs[i].bio, but it only drops devs[i].repl_bio when r10_bio->read_slot < 0. If discard reuses an r10bio that was previously used for a read, read_slot can still be non-negative, and discard cleanup can skip bio_put() on repl_bio. Reset read_slot to -1 when preparing an r10bio for discard so the replacement bio is always released correctly. | 16 Oct |
| CVE-2026-74361 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: nvme: fix FDP fdpcidx bounds check The fdpcidx bounds check sets n = NUMFDPC + 1 but used > instead of >=, incorrectly accepting fdp_idx when it equals n (i.e. NUMFDPC + 1). | 16 Oct |
| CVE-2026-74268 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: tcp: clear sock_ops cb flags before force-closing a child socket A child socket inherits the listener's bpf_sock_ops_cb_flags via sk_clone_lock(). If its setup fails in tcp_v4_syn_recv_sock() / tcp_v6_syn_recv_sock(), the child is freed through put_and_exit, where inet_csk_prepare_forced_close() drops the socket lock and tcp_done() runs without it. If BPF_SOCK_OPS_STATE_CB_FLAG was inherited, tcp_done() -> tcp_set_state() calls tcp_call_bpf(), which expects the lock and trips sock_owned_by_me(): WARNING: include/net/sock.h:1799 at tcp_set_state+0x433/0x550 RIP: 0010:tcp_set_state+0x433/0x550 include/net/sock.h:1799 Call Trace: <IRQ> tcp_done+0xba/0x250 net/ipv4/tcp.c:5095 tcp_v4_syn_recv_sock+0x850/0xa50 net/ipv4/tcp_ipv4.c:1787 tcp_check_req+0xf30/0x1360 net/ipv4/tcp_minisocks.c:926 tcp_v4_rcv+0x1047/0x1b50 net/ipv4/tcp_ipv4.c:2164 </IRQ> The child is freed before it is ever established, so it should run no sock_ops callback. Clear its cb flags in inet_csk_prepare_for_destroy_sock(), the common point for the IPv4, IPv6 and chtls forced-close paths and for the MPTCP ->syn_recv_sock() failure path (dispose_child), which reaches tcp_done() on a child that was never established too. | 16 Oct |
| CVE-2026-74267 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: net/sched: sch_codel: Do not call qdisc_tree_reduce_backlog during peek before restoring qlen Whenever codel drops packets during peek, it calls qdisc_tree_reduce_backlog. An issue arises because it calls qdisc_tree_reduce_backlog before it reincrements the qlen. If qlen drops to zero, but peek returns an skb, the parent's qlen_notify callback will be executed even though codel still has 1 packet on the queue and, thus, will mistakenly deactivate the parent's class causing issues like a wild memory access when qfq has codel as a child: [ 36.339843][ T370] Oops: general protection fault, probably for non-canonical address 0xfbd59c0000000024: 0000 [#1] SMP KASAN NOPTI [ 36.340408][ T370] KASAN: maybe wild-memory-access in range [0xdead000000000120-0xdead000000000127] [ 36.340737][ T370] CPU: 2 UID: 0 PID: 370 Comm: tc Not tainted 7.1.0-rc5-00287-g66e13b626592 #87 PREEMPT(full) [ 36.341113][ T370] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011 [ 36.341357][ T370] RIP: 0010:qfq_deactivate_agg (include/linux/list.h:1029 (discriminator 2) include/linux/list.h:1043 (discriminator 2) net/sched/sch_qfq.c:1369 (discriminator 2) net/sched/sch_qfq.c:1395 (discriminator 2)) sch_qfq [ 36.342221][ T370] RSP: 0018:ffff8881100ef370 EFLAGS: 00010216 [ 36.342422][ T370] RAX: 0000000000000000 RBX: ffff8881058a9568 RCX: dffffc0000000000 [ 36.342664][ T370] RDX: 1ffff11021064dc3 RSI: ffff888108326e00 RDI: dffffc0000000000 [ 36.342905][ T370] RBP: ffff8881058a8280 R08: dead000000000122 R09: 1bd5a00000000024 [ 36.343140][ T370] R10: fffffbfff2940329 R11: fffffbfff2940329 R12: 0000000000000000 [ 36.343383][ T370] R13: dead000000000100 R14: ffff8881058a9580 R15: ffff8881058a9578 [ 36.343631][ T370] FS: 00007fc04b0ca780(0000) GS:ffff888184fef000(0000) knlGS:0000000000000000 [ 36.343911][ T370] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 36.344116][ T370] CR2: 0000557c02c02000 CR3: 000000010e0ba000 CR4: 0000000000750ef0 [ 36.344359][ T370] PKRU: 55555554 [ 36.344481][ T370] Call Trace: ... [ 36.345054][ T370] qfq_reset_qdisc (net/sched/sch_qfq.c:357 net/sched/sch_qfq.c:1487) sch_qfq [ 36.345222][ T370] qdisc_reset (net/sched/sch_generic.c:1057) [ 36.345503][ T370] __qdisc_destroy (net/sched/sch_generic.c:1096) [ 36.345677][ T370] qdisc_graft (net/sched/sch_api.c:1062 net/sched/sch_api.c:1053 net/sched/sch_api.c:1159) [ 36.346335][ T370] tc_get_qdisc (net/sched/sch_api.c:1528 net/sched/sch_api.c:1556) Fix this by only calling qdisc_tree_reduce_backlog in peek after the qlen is restored. | 16 Oct |
| CVE-2026-74255 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: tipc: fix UAF in tipc_l2_send_msg() Syzbot reported a slab-use-after-free in ipvlan_hard_header() when called from tipc_l2_send_msg(). The root cause is that tipc_disable_l2_media() calls synchronize_net() while b->media_ptr is still valid. This allows concurrent RCU readers to obtain the device pointer after synchronize_net() has finished. The pointer is cleared later in bearer_disable(), but without any subsequent synchronization, allowing the device to be freed while still in use by readers. Fix this by clearing b->media_ptr in tipc_disable_l2_media() before calling synchronize_net(). This is safe to do now because the call order in bearer_disable() was reversed in 0d051bf93c06 ("tipc: make bearer packet filtering generic") to call tipc_node_delete_links() (which needs the pointer) before disable_media(). https: //lore.kernel.org/netdev/[email protected]/T/#u | 16 Oct |
| CVE-2026-72491 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: net/9p: fix race condition on rdma->state in trans_rdma.c The rdma->state field is modified without holding req_lock in both recv_done() and p9_cm_event_handler(), while rdma_request() accesses the same field under the req_lock spinlock. This inconsistent locking creates a race condition: - recv_done() running in softirq completion context sets rdma->state = P9_RDMA_FLUSHING without acquiring req_lock - p9_cm_event_handler() modifies rdma->state at multiple points (ADDR_RESOLVED, ROUTE_RESOLVED, ESTABLISHED, CLOSED) without req_lock - rdma_request() uses spin_lock_irqsave(&rdma->req_lock, flags) to protect the read-modify-write of rdma->state The race can cause lost state transitions: recv_done() or the CM event handler could set state to FLUSHING/CLOSED while rdma_request() is concurrently checking or modifying state under the lock, leading to the FLUSHING transition being silently overwritten by CLOSING. This corrupts the connection state machine and can cause use-after-free on RDMA request objects during teardown. Fix by adding req_lock protection to all rdma->state modifications in recv_done() and p9_cm_event_handler(), matching the pattern already used in rdma_request(). Use spin_lock_irqsave/spin_unlock_irqrestore in the CM event handler since it can race with recv_done() which runs in softirq context. Tested with a kernel module that races two threads (simulating rdma_request and recv_done/CM handler) on rdma->state with proper locking: 5.5M+ FLUSHING writes over 27M iterations with 0 lost transitions. | 16 Oct |
| CVE-2026-72473 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: xprtrdma: Decouple req recycling from RPC completion rl_kref formerly served two distinct lifetimes through a single refcount: it gated when a Reply could wake its RPC task, and it gated when an rpcrdma_req could return to its free pool. The marshal path took the Send-side reference only when SGEs needed DMA-unmap (sc_unmap_count > 0), which made a Send carrying only pre-registered buffers an exception: the Reply handler dropped rl_kref from 1 to 0 and freed the req while the HCA might still be DMA-reading from its send buffer. Give rl_kref a narrower job. The RPC layer takes one reference when slot allocation hands a req out. rpcrdma_prepare_send_sges() takes a Send-side reference unconditionally after WR preparation succeeds. xprt_rdma_free_slot() and xprt_rdma_bc_free_rqst() drop the RPC-layer reference; rpcrdma_sendctx_unmap() drops the Send-side reference. The req returns to its free pool only after both owners have signed off. The existing kref_init(&req->rl_kref) call in rpcrdma_prepare_send_sges() is removed. Initialization moves to the slot-allocation paths (xprt_rdma_alloc_slot and rpcrdma_bc_rqst_get), and the release callback re-arms rl_kref before the req returns to a free pool. A re-init in the marshal path would discard the RPC-layer reference that already exists on entry. Three invariants follow: - Any rpcrdma_req held by an rpc_rqst has rl_kref >= 1. xprt_rdma_alloc_slot(), rpcrdma_bc_rqst_get(), and the backlog-wake branch in xprt_rdma_alloc_slot() each kref_init rl_kref before publishing the req. Without this invariant, an RPC task that aborts between slot allocation and marshal (gss_refresh failure or signal during call_connect, for example) would drive xprt_release() -> xprt_rdma_free_slot() -> kref_put against a refcount of zero, saturating refcount_t and stranding the slot. - The Send-side reference is taken only after WR prep succeeds. A mapping failure in rpcrdma_prepare_send_sges() runs rpcrdma_sendctx_cancel(), which DMA-unmaps the sendctx and clears sc_req without touching rl_kref. The sendctx ring walks in rpcrdma_sendctx_put_locked() and rpcrdma_sendctxs_destroy() skip entries with sc_req == NULL, so a burst of -EIO marshal failures cannot hold reqs off rb_send_bufs. - The release callback re-arms rl_kref so the next consumer enters with the invariant satisfied. Replies now complete the RPC directly. rpcrdma_reply_handler() calls rpcrdma_complete_rqst() in place of kref_put on the non-LocalInv branch. The LocalInv branch already completes the RPC from frwr_unmap_async() and is unaffected. Because Send-side references can now outlive RPC completion, connection teardown drains sendctx entries whose unsignaled Sends never had a later signaled completion to walk the ring. rpcrdma_sendctxs_destroy() walks the active range and runs rpcrdma_sendctx_unmap() on each entry with a non-NULL sc_req before the request buffers are reset, and is moved ahead of rpcrdma_reqs_reset() in rpcrdma_xprt_disconnect() so the reqs are still in their pre-reset state when the Send-side refs are released. The drain creates a teardown-ordering hazard on the backchannel path. With the new lifetime, releasing a bc_prealloc req from rpcrdma_req_release() re-adds it to bc_pa_list. The disconnect in xprt_rdma_destroy() runs after xprt_destroy_backchannel() has already emptied bc_pa_list, so the drained reqs would otherwise leak. xprt_rdma_destroy() now runs xprt_rdma_bc_destroy(xprt, 0) a second time after the disconnect to reclaim them. | 16 Oct |
| CVE-2026-72466 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: xprtrdma: Fix bcall rep leak and unbounded peek rpcrdma_is_bcall() decodes a reply's first words to decide whether the frame is a backchannel call. Two issues in that decode path let a short or malformed reply leak the receive buffer and drain the Receive queue. First, the speculative peek p = xdr_inline_decode(xdr, 0); /* five p++ reads follow */ asks xdr_inline_decode() for zero bytes, which returns xdr->p without consulting xdr->end. The five subsequent __be32 reads can then walk up to 20 bytes past the wire payload into stale regbuf contents and misclassify the reply as a backchannel call. Second, after the post-peek p = xdr_inline_decode(xdr, 3 * sizeof(*p)); if (unlikely(!p)) return true; the short-header arm returns true without calling rpcrdma_bc_receive_call(). The contract with the caller is that a true return transfers ownership of rep to the backchannel path: rpcrdma_reply_handler() if (rpcrdma_is_bcall(r_xprt, rep)) return; /* bare return, skips out_post */ ... out_post: rpcrdma_post_recvs(r_xprt, credits + ...); Because rpcrdma_bc_receive_call() never ran, no one took rep, but rpcrdma_reply_handler still bare-returns past rpcrdma_rep_put() and rpcrdma_post_recvs(). The rep, with its persistently DMA-mapped receive buffer, is orphaned on rb_all_reps and freed only at transport teardown. This completion reposts nothing, so its slot is reclaimed only when a later forward-channel reply reaches out_post and rpcrdma_post_recvs() allocates a fresh rep to backfill; absent that traffic the Receive queue drains and the peer's Sends draw RNR NAKs. Fix by consulting xdr->end after the zero-length peek so the five __be32 reads cannot run unless 20 bytes of wire payload remain. A byte-precise comparison against xdr->end is required because a non-4-aligned receive rounds the stream's word count up past the true payload. Also return false from the short-header arm so the reply falls through the normal out_norqst cleanup chain (rpcrdma_rep_put() plus rpcrdma_post_recvs()). | 16 Oct |
| CVE-2026-72436 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: netfilter: ipset: Don't use test_bit() in lockless RCU readers in hash types Sashiko pointed out that there are a few lockless RCU readers using test_bit() which is a relaxed atomic operation and provides no memory barrier guarantees. Use test_bit_acquire() instead where the operation may run parallel with add/del/gc, i.e. is not one from the next cases - protected by region lock - in a set destroy phase - in a new/temporary set creation phase | 16 Oct |
| CVE-2026-72351 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: gue: validate REMCSUM private option length GUE private flags can indicate that remote checksum offload metadata is present. The private flags field itself is accounted for by guehdr_flags_len(), but guehdr_priv_flags_len() currently returns 0 even when GUE_PFLAG_REMCSUM is set. This lets a packet with only the private flags field pass validate_gue_flags(), after which gue_remcsum() and gue_gro_remcsum() read the missing REMCSUM start/offset fields from the following bytes. Account for GUE_PLEN_REMCSUM when GUE_PFLAG_REMCSUM is present so that malformed packets are rejected during option validation. | 16 Oct |
| CVE-2026-72339 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: qede: fix off-by-one in BD ring consumption on build_skb failure qede_rx_build_skb() and qede_tpa_rx_build_skb() do not check for a NULL return from qede_build_skb(). When it returns NULL under memory pressure, the functions still consume a BD from the ring before returning NULL. The callers then recycle additional BDs, resulting in one extra BD being consumed (off-by-one). This desynchronizes the BD ring, which can corrupt DMA page reference counts and lead to SLUB freelist corruption. Commit 4e910dbe3650 ("qede: confirm skb is allocated before using") added a NULL check inside qede_build_skb() to prevent a NULL pointer dereference, but did not address the missing NULL checks in the callers, making this off-by-one reachable. Fix this by adding NULL checks for the return value of qede_build_skb() in both qede_rx_build_skb() and qede_tpa_rx_build_skb(), returning NULL immediately before any BD ring manipulation. | 16 Oct |
| CVE-2026-72323 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: ipv4: igmp: Fix potential UAF in igmp_gq_start_timer() A race condition exists between device teardown (inetdev_destroy) and incoming IGMP query processing (igmp_rcv), leading to a Use-After-Free in the IGMP timer callback. During device destruction, inetdev_destroy() drops the primary reference to in_device, which can drop its refcount to 0. The actual freeing of in_device memory is deferred via RCU (using call_rcu()). Concurrently, igmp_rcv() runs under RCU read lock and obtains the in_device pointer. Because the memory is RCU-protected, CPU-0 can safely dereference in_device even if its refcount has hit 0. However, if CPU-0 calls igmp_gq_start_timer() and re-arms the timer, it attempts to acquire a reference using in_dev_hold(). This increments the refcount from 0 to 1, triggering a "refcount_t: addition on 0" warning. Since the in_device memory is still scheduled to be freed after the RCU grace period (as the free callback does not check the refcount again), the device is freed while the timer is still armed. When the timer expires, it accesses the freed memory, causing a kernel panic. Fix this by using refcount_inc_not_zero() (via a new helper in_dev_hold_safe()) to prevent acquiring a reference if the device is already being destroyed. If the refcount is 0, we do not arm the timer. A similar issue in IPv6 MLD is fixed in a subsequent patch. | 16 Oct |
| CVE-2026-72322 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: ipv6: mcast: Fix potential UAF in MLD delayed work A race condition exists between device teardown and incoming MLD query processing, leading to a Use-After-Free in the MLD delayed work. During device destruction, the primary reference to inet6_dev is dropped, which can drop its refcount to 0. The actual freeing of inet6_dev memory is deferred via RCU. Concurrently, the packet receive path runs under RCU read lock and obtains the inet6_dev pointer. Because the memory is RCU-protected, CPU-0 can safely dereference inet6_dev even if its refcount has hit 0. However, if CPU-0 calls igmp6_event_query() and schedules delayed work, it attempts to acquire a reference using in6_dev_hold(). This increments the refcount from 0 to 1, triggering a "refcount_t: addition on 0" warning. Since the inet6_dev memory is still scheduled to be freed after the RCU grace period, the device is freed while the work is still scheduled. When the work runs, it accesses the freed memory, causing a kernel panic. Fix this by using refcount_inc_not_zero() (via a new helper in6_dev_hold_safe()) to prevent acquiring a reference if the device is already being destroyed. If the refcount is 0, we do not schedule the work. | 16 Oct |
| CVE-2026-72319 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: ipvs: ensure inner headers in ICMP errors are in headroom Sashiko points out that after stripping the outer headers with pskb_pull() we should ensure the inner IP headers in ICMP errors from tunnels are present in the skb headroom for functions like ipv4_update_pmtu(), icmp_send() and IP_VS_DBG(). Also, add more checks for the length of the inner headers. | 16 Oct |
| CVE-2026-72317 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: SUNRPC: pin upper rpc_clnt across the TLS connect_worker The TLS connect path has a use-after-free: nothing pins the upper rpc_clnt across the delayed connect_worker. xs_connect() stores task->tk_client in sock_xprt::clnt as a raw pointer and queues the worker; for TLS-secured transports that worker is xs_tcp_tls_setup_socket(), which reads several fields out of the saved pointer (cl_timeout, cl_program, cl_prog, cl_vers, cl_cred, cl_stats) to construct the args for the inner handshake rpc_clnt. The xprt does not reference the rpc_clnt; the rpc_clnt references the xprt. xs_destroy() does cancel the connect_worker, but it runs only when the xprt's refcount drops to zero, which cannot happen until the rpc_clnt releases its cl_xprt reference in rpc_free_client_work(). When a TLS handshake fails fatally (for example, an mTLS mount whose client cert does not match the server), the connecting task is woken with -EACCES and exits, the mount caller invokes rpc_shutdown_client(), and the upper rpc_clnt is freed before the queued connect_worker fires. xs_tcp_tls_setup_socket() then dereferences the freed clnt, producing the refcount_t underflow Michael Nemanov reported. Take a reference on the upper rpc_clnt in xs_connect() for TLS transports via a new rpc_hold_client() helper, and drop it in the connect_worker's exit path with rpc_release_client(). The xprt_lock_connect() / xprt_unlock_connect() pairing already serialises xs_connect() with xs_tcp_tls_setup_socket(), so the take and release are balanced one-for-one. The non-TLS connect worker (xs_tcp_setup_socket) never reads sock_xprt::clnt, so leave that path alone and avoid the clnt-holds-xprt-holds-clnt cycle that would otherwise prevent xprt destruction. | 16 Oct |
Download these 1000 as CSV (the first thousand in this order) · subscribe to this list.
EPSS scores: 2026-10-30. NVD cursor: 2026-10-29 00:22. The News page shows only notable CVEs (KEV, your stack, new criticals, EPSS over 50%, or active exploitation per SSVC); this table has all of them.