Vulnerabilities
All
My stack
Known exploited
Public exploit
Critical (9+)
Likely exploited (EPSS ≥ 50%)
Changed, 24 h
New, 24 h
Sort:
risk
modified
published
CVSS
EPSS
| CVE | CVSS | EPSS | Vendor, product | Description | Modified |
|---|---|---|---|---|---|
| CVE-2026-23396 | 5.5 medium | 0.00% | linux, linux_kernel | In the Linux kernel, the following vulnerability has been resolved: wifi: mac80211: fix NULL deref in mesh_matches_local() mesh_matches_local() unconditionally dereferences ie->mesh_config to compare mesh configuration parameters. When called from mesh_rx_csa_frame(), the parsed action-frame elements may not contain a Mesh Configuration IE, leaving ie->mesh_config NULL and triggering a kernel NULL pointer dereference. The other two callers are already safe: - ieee80211_mesh_rx_bcn_presp() checks !elems->mesh_config before calling mesh_matches_local() - mesh_plink_get_event() is only reached through mesh_process_plink_frame(), which checks !elems->mesh_config, too mesh_rx_csa_frame() is the only caller that passes raw parsed elements to mesh_matches_local() without guarding mesh_config. An adjacent attacker can exploit this by sending a crafted CSA action frame that includes a valid Mesh ID IE but omits the Mesh Configuration IE, crashing the kernel. The captured crash log: Oops: general protection fault, probably for non-canonical address ... KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007] Workqueue: events_unbound cfg80211_wiphy_work [...] Call Trace: <TASK> ? __pfx_mesh_matches_local (net/mac80211/mesh.c:65) ieee80211_mesh_rx_queued_mgmt (net/mac80211/mesh.c:1686) [...] ieee80211_iface_work (net/mac80211/iface.c:1754 net/mac80211/iface.c:1802) [...] cfg80211_wiphy_work (net/wireless/core.c:426) process_one_work (net/kernel/workqueue.c:3280) ? assign_work (net/kernel/workqueue.c:1219) worker_thread (net/kernel/workqueue.c:3352) ? __pfx_worker_thread (net/kernel/workqueue.c:3385) kthread (net/kernel/kthread.c:436) [...] ret_from_fork_asm (net/arch/x86/entry/entry_64.S:255) </TASK> This patch adds a NULL check for ie->mesh_config at the top of mesh_matches_local() to return false early when the Mesh Configuration IE is absent. | 15 Oct |
| CVE-2024-58056 | 5.5 medium | 0.00% | linux, linux_kernel | In the Linux kernel, the following vulnerability has been resolved: remoteproc: core: Fix ida_free call while not allocated In the rproc_alloc() function, on error, put_device(&rproc->dev) is called, leading to the call of the rproc_type_release() function. An error can occurs before ida_alloc is called. In such case in rproc_type_release(), the condition (rproc->index >= 0) is true as rproc->index has been initialized to 0. ida_free() is called reporting a warning: [ 4.181906] WARNING: CPU: 1 PID: 24 at lib/idr.c:525 ida_free+0x100/0x164 [ 4.186378] stm32-display-dsi 5a000000.dsi: Fixed dependency cycle(s) with /soc/dsi@5a000000/panel@0 [ 4.188854] ida_free called for id=0 which is not allocated. [ 4.198256] mipi-dsi 5a000000.dsi.0: Fixed dependency cycle(s) with /soc/dsi@5a000000 [ 4.203556] Modules linked in: panel_orisetech_otm8009a dw_mipi_dsi_stm(+) gpu_sched dw_mipi_dsi stm32_rproc stm32_crc32 stm32_ipcc(+) optee(+) [ 4.224307] CPU: 1 UID: 0 PID: 24 Comm: kworker/u10:0 Not tainted 6.12.0 #442 [ 4.231481] Hardware name: STM32 (Device Tree Support) [ 4.236627] Workqueue: events_unbound deferred_probe_work_func [ 4.242504] Call trace: [ 4.242522] unwind_backtrace from show_stack+0x10/0x14 [ 4.250218] show_stack from dump_stack_lvl+0x50/0x64 [ 4.255274] dump_stack_lvl from __warn+0x80/0x12c [ 4.260134] __warn from warn_slowpath_fmt+0x114/0x188 [ 4.265199] warn_slowpath_fmt from ida_free+0x100/0x164 [ 4.270565] ida_free from rproc_type_release+0x38/0x60 [ 4.275832] rproc_type_release from device_release+0x30/0xa0 [ 4.281601] device_release from kobject_put+0xc4/0x294 [ 4.286762] kobject_put from rproc_alloc.part.0+0x208/0x28c [ 4.292430] rproc_alloc.part.0 from devm_rproc_alloc+0x80/0xc4 [ 4.298393] devm_rproc_alloc from stm32_rproc_probe+0xd0/0x844 [stm32_rproc] [ 4.305575] stm32_rproc_probe [stm32_rproc] from platform_probe+0x5c/0xbc Calling ida_alloc earlier in rproc_alloc ensures that the rproc->index is properly set. | 15 Oct |
| CVE-2024-43889 | 5.5 medium | 0.00% | linux, linux_kernel | In the Linux kernel, the following vulnerability has been resolved: padata: Fix possible divide-by-0 panic in padata_mt_helper() We are hit with a not easily reproducible divide-by-0 panic in padata.c at bootup time. [ 10.017908] Oops: divide error: 0000 1 PREEMPT SMP NOPTI [ 10.017908] CPU: 26 PID: 2627 Comm: kworker/u1666:1 Not tainted 6.10.0-15.el10.x86_64 #1 [ 10.017908] Hardware name: Lenovo ThinkSystem SR950 [7X12CTO1WW]/[7X12CTO1WW], BIOS [PSE140J-2.30] 07/20/2021 [ 10.017908] Workqueue: events_unbound padata_mt_helper [ 10.017908] RIP: 0010:padata_mt_helper+0x39/0xb0 : [ 10.017963] Call Trace: [ 10.017968] <TASK> [ 10.018004] ? padata_mt_helper+0x39/0xb0 [ 10.018084] process_one_work+0x174/0x330 [ 10.018093] worker_thread+0x266/0x3a0 [ 10.018111] kthread+0xcf/0x100 [ 10.018124] ret_from_fork+0x31/0x50 [ 10.018138] ret_from_fork_asm+0x1a/0x30 [ 10.018147] </TASK> Looking at the padata_mt_helper() function, the only way a divide-by-0 panic can happen is when ps->chunk_size is 0. The way that chunk_size is initialized in padata_do_multithreaded(), chunk_size can be 0 when the min_chunk in the passed-in padata_mt_job structure is 0. Fix this divide-by-0 panic by making sure that chunk_size will be at least 1 no matter what the input parameters are. | 15 Oct |
| CVE-2024-40916 | 5.5 medium | 0.00% | linux, linux_kernel | In the Linux kernel, the following vulnerability has been resolved: drm/exynos: hdmi: report safe 640x480 mode as a fallback when no EDID found When reading EDID fails and driver reports no modes available, the DRM core adds an artificial 1024x786 mode to the connector. Unfortunately some variants of the Exynos HDMI (like the one in Exynos4 SoCs) are not able to drive such mode, so report a safe 640x480 mode instead of nothing in case of the EDID reading failure. This fixes the following issue observed on Trats2 board since commit 13d5b040363c ("drm/exynos: do not return negative values from .get_modes()"): [drm] Exynos DRM: using 11c00000.fimd device for DMA mapping operations exynos-drm exynos-drm: bound 11c00000.fimd (ops fimd_component_ops) exynos-drm exynos-drm: bound 12c10000.mixer (ops mixer_component_ops) exynos-dsi 11c80000.dsi: [drm:samsung_dsim_host_attach] Attached s6e8aa0 device (lanes:4 bpp:24 mode-flags:0x10b) exynos-drm exynos-drm: bound 11c80000.dsi (ops exynos_dsi_component_ops) exynos-drm exynos-drm: bound 12d00000.hdmi (ops hdmi_component_ops) [drm] Initialized exynos 1.1.0 20180330 for exynos-drm on minor 1 exynos-hdmi 12d00000.hdmi: [drm:hdmiphy_enable.part.0] *ERROR* PLL could not reach steady state panel-samsung-s6e8aa0 11c80000.dsi.0: ID: 0xa2, 0x20, 0x8c exynos-mixer 12c10000.mixer: timeout waiting for VSYNC ------------[ cut here ]------------ WARNING: CPU: 1 PID: 11 at drivers/gpu/drm/drm_atomic_helper.c:1682 drm_atomic_helper_wait_for_vblanks.part.0+0x2b0/0x2b8 [CRTC:70:crtc-1] vblank wait timed out Modules linked in: CPU: 1 PID: 11 Comm: kworker/u16:0 Not tainted 6.9.0-rc5-next-20240424 #14913 Hardware name: Samsung Exynos (Flattened Device Tree) Workqueue: events_unbound deferred_probe_work_func Call trace: unwind_backtrace from show_stack+0x10/0x14 show_stack from dump_stack_lvl+0x68/0x88 dump_stack_lvl from __warn+0x7c/0x1c4 __warn from warn_slowpath_fmt+0x11c/0x1a8 warn_slowpath_fmt from drm_atomic_helper_wait_for_vblanks.part.0+0x2b0/0x2b8 drm_atomic_helper_wait_for_vblanks.part.0 from drm_atomic_helper_commit_tail_rpm+0x7c/0x8c drm_atomic_helper_commit_tail_rpm from commit_tail+0x9c/0x184 commit_tail from drm_atomic_helper_commit+0x168/0x190 drm_atomic_helper_commit from drm_atomic_commit+0xb4/0xe0 drm_atomic_commit from drm_client_modeset_commit_atomic+0x23c/0x27c drm_client_modeset_commit_atomic from drm_client_modeset_commit_locked+0x60/0x1cc drm_client_modeset_commit_locked from drm_client_modeset_commit+0x24/0x40 drm_client_modeset_commit from __drm_fb_helper_restore_fbdev_mode_unlocked+0x9c/0xc4 __drm_fb_helper_restore_fbdev_mode_unlocked from drm_fb_helper_set_par+0x2c/0x3c drm_fb_helper_set_par from fbcon_init+0x3d8/0x550 fbcon_init from visual_init+0xc0/0x108 visual_init from do_bind_con_driver+0x1b8/0x3a4 do_bind_con_driver from do_take_over_console+0x140/0x1ec do_take_over_console from do_fbcon_takeover+0x70/0xd0 do_fbcon_takeover from fbcon_fb_registered+0x19c/0x1ac fbcon_fb_registered from register_framebuffer+0x190/0x21c register_framebuffer from __drm_fb_helper_initial_config_and_unlock+0x350/0x574 __drm_fb_helper_initial_config_and_unlock from exynos_drm_fbdev_client_hotplug+0x6c/0xb0 exynos_drm_fbdev_client_hotplug from drm_client_register+0x58/0x94 drm_client_register from exynos_drm_bind+0x160/0x190 exynos_drm_bind from try_to_bring_up_aggregate_device+0x200/0x2d8 try_to_bring_up_aggregate_device from __component_add+0xb0/0x170 __component_add from mixer_probe+0x74/0xcc mixer_probe from platform_probe+0x5c/0xb8 platform_probe from really_probe+0xe0/0x3d8 really_probe from __driver_probe_device+0x9c/0x1e4 __driver_probe_device from driver_probe_device+0x30/0xc0 driver_probe_device from __device_attach_driver+0xa8/0x120 __device_attach_driver from bus_for_each_drv+0x80/0xcc bus_for_each_drv from __device_attach+0xac/0x1fc __device_attach from bus_probe_device+0x8c/0x90 bus_probe_device from deferred_probe_work_func+0 ---truncated--- | 15 Oct |
| CVE-2024-35990 | 5.5 medium | 0.00% | linux, linux_kernel | In the Linux kernel, the following vulnerability has been resolved: dma: xilinx_dpdma: Fix locking There are several places where either chan->lock or chan->vchan.lock was not held. Add appropriate locking. This fixes lockdep warnings like [ 31.077578] ------------[ cut here ]------------ [ 31.077831] WARNING: CPU: 2 PID: 40 at drivers/dma/xilinx/xilinx_dpdma.c:834 xilinx_dpdma_chan_queue_transfer+0x274/0x5e0 [ 31.077953] Modules linked in: [ 31.078019] CPU: 2 PID: 40 Comm: kworker/u12:1 Not tainted 6.6.20+ #98 [ 31.078102] Hardware name: xlnx,zynqmp (DT) [ 31.078169] Workqueue: events_unbound deferred_probe_work_func [ 31.078272] pstate: 600000c5 (nZCv daIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 31.078377] pc : xilinx_dpdma_chan_queue_transfer+0x274/0x5e0 [ 31.078473] lr : xilinx_dpdma_chan_queue_transfer+0x270/0x5e0 [ 31.078550] sp : ffffffc083bb2e10 [ 31.078590] x29: ffffffc083bb2e10 x28: 0000000000000000 x27: ffffff880165a168 [ 31.078754] x26: ffffff880164e920 x25: ffffff880164eab8 x24: ffffff880164d480 [ 31.078920] x23: ffffff880165a148 x22: ffffff880164e988 x21: 0000000000000000 [ 31.079132] x20: ffffffc082aa3000 x19: ffffff880164e880 x18: 0000000000000000 [ 31.079295] x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000000 [ 31.079453] x14: 0000000000000000 x13: ffffff8802263dc0 x12: 0000000000000001 [ 31.079613] x11: 0001ffc083bb2e34 x10: 0001ff880164e98f x9 : 0001ffc082aa3def [ 31.079824] x8 : 0001ffc082aa3dec x7 : 0000000000000000 x6 : 0000000000000516 [ 31.079982] x5 : ffffffc7f8d43000 x4 : ffffff88003c9c40 x3 : ffffffffffffffff [ 31.080147] x2 : ffffffc7f8d43000 x1 : 00000000000000c0 x0 : 0000000000000000 [ 31.080307] Call trace: [ 31.080340] xilinx_dpdma_chan_queue_transfer+0x274/0x5e0 [ 31.080518] xilinx_dpdma_issue_pending+0x11c/0x120 [ 31.080595] zynqmp_disp_layer_update+0x180/0x3ac [ 31.080712] zynqmp_dpsub_plane_atomic_update+0x11c/0x21c [ 31.080825] drm_atomic_helper_commit_planes+0x20c/0x684 [ 31.080951] drm_atomic_helper_commit_tail+0x5c/0xb0 [ 31.081139] commit_tail+0x234/0x294 [ 31.081246] drm_atomic_helper_commit+0x1f8/0x210 [ 31.081363] drm_atomic_commit+0x100/0x140 [ 31.081477] drm_client_modeset_commit_atomic+0x318/0x384 [ 31.081634] drm_client_modeset_commit_locked+0x8c/0x24c [ 31.081725] drm_client_modeset_commit+0x34/0x5c [ 31.081812] __drm_fb_helper_restore_fbdev_mode_unlocked+0x104/0x168 [ 31.081899] drm_fb_helper_set_par+0x50/0x70 [ 31.081971] fbcon_init+0x538/0xc48 [ 31.082047] visual_init+0x16c/0x23c [ 31.082207] do_bind_con_driver.isra.0+0x2d0/0x634 [ 31.082320] do_take_over_console+0x24c/0x33c [ 31.082429] do_fbcon_takeover+0xbc/0x1b0 [ 31.082503] fbcon_fb_registered+0x2d0/0x34c [ 31.082663] register_framebuffer+0x27c/0x38c [ 31.082767] __drm_fb_helper_initial_config_and_unlock+0x5c0/0x91c [ 31.082939] drm_fb_helper_initial_config+0x50/0x74 [ 31.083012] drm_fbdev_dma_client_hotplug+0xb8/0x108 [ 31.083115] drm_client_register+0xa0/0xf4 [ 31.083195] drm_fbdev_dma_setup+0xb0/0x1cc [ 31.083293] zynqmp_dpsub_drm_init+0x45c/0x4e0 [ 31.083431] zynqmp_dpsub_probe+0x444/0x5e0 [ 31.083616] platform_probe+0x8c/0x13c [ 31.083713] really_probe+0x258/0x59c [ 31.083793] __driver_probe_device+0xc4/0x224 [ 31.083878] driver_probe_device+0x70/0x1c0 [ 31.083961] __device_attach_driver+0x108/0x1e0 [ 31.084052] bus_for_each_drv+0x9c/0x100 [ 31.084125] __device_attach+0x100/0x298 [ 31.084207] device_initial_probe+0x14/0x20 [ 31.084292] bus_probe_device+0xd8/0xdc [ 31.084368] deferred_probe_work_func+0x11c/0x180 [ 31.084451] process_one_work+0x3ac/0x988 [ 31.084643] worker_thread+0x398/0x694 [ 31.084752] kthread+0x1bc/0x1c0 [ 31.084848] ret_from_fork+0x10/0x20 [ 31.084932] irq event stamp: 64549 [ 31.084970] hardirqs last enabled at (64548): [<ffffffc081adf35c>] _raw_spin_unlock_irqrestore+0x80/0x90 [ 31.085157] ---truncated--- | 15 Oct |
| CVE-2024-27004 | 5.5 medium | 0.00% | linux, debian, linux_kernel, debian_linux, fedora | In the Linux kernel, the following vulnerability has been resolved: clk: Get runtime PM before walking tree during disable_unused Doug reported [1] the following hung task: INFO: task swapper/0:1 blocked for more than 122 seconds. Not tainted 5.15.149-21875-gf795ebc40eb8 #1 "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. task:swapper/0 state:D stack: 0 pid: 1 ppid: 0 flags:0x00000008 Call trace: __switch_to+0xf4/0x1f4 __schedule+0x418/0xb80 schedule+0x5c/0x10c rpm_resume+0xe0/0x52c rpm_resume+0x178/0x52c __pm_runtime_resume+0x58/0x98 clk_pm_runtime_get+0x30/0xb0 clk_disable_unused_subtree+0x58/0x208 clk_disable_unused_subtree+0x38/0x208 clk_disable_unused_subtree+0x38/0x208 clk_disable_unused_subtree+0x38/0x208 clk_disable_unused_subtree+0x38/0x208 clk_disable_unused+0x4c/0xe4 do_one_initcall+0xcc/0x2d8 do_initcall_level+0xa4/0x148 do_initcalls+0x5c/0x9c do_basic_setup+0x24/0x30 kernel_init_freeable+0xec/0x164 kernel_init+0x28/0x120 ret_from_fork+0x10/0x20 INFO: task kworker/u16:0:9 blocked for more than 122 seconds. Not tainted 5.15.149-21875-gf795ebc40eb8 #1 "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. task:kworker/u16:0 state:D stack: 0 pid: 9 ppid: 2 flags:0x00000008 Workqueue: events_unbound deferred_probe_work_func Call trace: __switch_to+0xf4/0x1f4 __schedule+0x418/0xb80 schedule+0x5c/0x10c schedule_preempt_disabled+0x2c/0x48 __mutex_lock+0x238/0x488 __mutex_lock_slowpath+0x1c/0x28 mutex_lock+0x50/0x74 clk_prepare_lock+0x7c/0x9c clk_core_prepare_lock+0x20/0x44 clk_prepare+0x24/0x30 clk_bulk_prepare+0x40/0xb0 mdss_runtime_resume+0x54/0x1c8 pm_generic_runtime_resume+0x30/0x44 __genpd_runtime_resume+0x68/0x7c genpd_runtime_resume+0x108/0x1f4 __rpm_callback+0x84/0x144 rpm_callback+0x30/0x88 rpm_resume+0x1f4/0x52c rpm_resume+0x178/0x52c __pm_runtime_resume+0x58/0x98 __device_attach+0xe0/0x170 device_initial_probe+0x1c/0x28 bus_probe_device+0x3c/0x9c device_add+0x644/0x814 mipi_dsi_device_register_full+0xe4/0x170 devm_mipi_dsi_device_register_full+0x28/0x70 ti_sn_bridge_probe+0x1dc/0x2c0 auxiliary_bus_probe+0x4c/0x94 really_probe+0xcc/0x2c8 __driver_probe_device+0xa8/0x130 driver_probe_device+0x48/0x110 __device_attach_driver+0xa4/0xcc bus_for_each_drv+0x8c/0xd8 __device_attach+0xf8/0x170 device_initial_probe+0x1c/0x28 bus_probe_device+0x3c/0x9c deferred_probe_work_func+0x9c/0xd8 process_one_work+0x148/0x518 worker_thread+0x138/0x350 kthread+0x138/0x1e0 ret_from_fork+0x10/0x20 The first thread is walking the clk tree and calling clk_pm_runtime_get() to power on devices required to read the clk hardware via struct clk_ops::is_enabled(). This thread holds the clk prepare_lock, and is trying to runtime PM resume a device, when it finds that the device is in the process of resuming so the thread schedule()s away waiting for the device to finish resuming before continuing. The second thread is runtime PM resuming the same device, but the runtime resume callback is calling clk_prepare(), trying to grab the prepare_lock waiting on the first thread. This is a classic ABBA deadlock. To properly fix the deadlock, we must never runtime PM resume or suspend a device with the clk prepare_lock held. Actually doing that is near impossible today because the global prepare_lock would have to be dropped in the middle of the tree, the device runtime PM resumed/suspended, and then the prepare_lock grabbed again to ensure consistency of the clk tree topology. If anything changes with the clk tree in the meantime, we've lost and will need to start the operation all over again. Luckily, most of the time we're simply incrementing or decrementing the runtime PM count on an active device, so we don't have the chance to schedule away with the prepare_lock held. Let's fix this immediate problem that can be ---truncated--- | 15 Oct |
| CVE-2026-50045 | 5.3 medium | 0.00% | nlnetlabs, unbound | In NLnet Labs Unbound 1.22.0 up to and including 1.25.1, a single client query for a deeply nested name under a DNSSEC-signed parent can cause Unbound to send more upstream packets per client query than the configured 'max-global-quota'. This effectively bypasses a security configuration that limits upstream amplification traffic. | Sat 24 Oct |
| CVE-2026-50251 | 5.3 medium | 0.00% | nlnetlabs, unbound | In NLnet Labs Unbound up to and including version 1.25.1, when 'unwanted-reply-threshold' is enabled (set to any value greater than zero), glue records of 0.0.0.0/::0 can short-circuit Unbound, on systems that can direct such traffic, by issuing DNS queries and receiving seemingly unwanted replies since the remote IP does not match the original source IP of 0.0.0.0/::0. This behavior keeps on looping for the glue records and pushing the counter to the configured 'unwanted-reply-threshold' that triggers a defensive cache clear. A malicious actor who controls a delegation that returns in-bailiwick glue of 0.0.0.0/::0 can drive the counter to the limit of 'unwanted-reply-threshold' to the threshold and trigger a cache clean of the message and rrset caches; at will, indefinitely, without sending a single spoofed packet. The iterator uses the 0.0.0.0/::0 glue, and a system that can route this (e.g., Linux kernel routes the datagram over loopback), Unbound's own listener answers from 127.0.0.1. Because of the mismatch of 0.0.0.0 and 127.0.0.1, in this example, Unbound accounts the reply as an unwanted (probably spoofed) answer. The counter resets to zero on every cache flush, so the attack loops forever. | Sat 24 Oct |
| CVE-2026-109125 | 5.3 medium | 0.00% | no CPE yet | In NLnet Labs Unbound up to and including version 1.26.1, an observable cache-level side-channel can be exposed with 'unwanted-reply-threshold > 0' configurations (not a default configuration). If a response-like UDP datagram reaches the upstream source port currently used by a recursive query, but its TXID does not match any pending query, Unbound counts the packet as an unwanted reply. When the accumulated count reaches the configured threshold, Unbound clears the worker's RRset cache and message cache. This cache clear action does not destroy the current upstream UDP pending query. Therefore, an external observer can distinguish whether a candidate port matches the current upstream source port by checking whether an existing cached item has been cleared. This is a cache side-channel vulnerability that can be used to probe the upstream source port. Although the attack is not feasible on default configurations and the suggested value (10 million) makes it an ureliable attack on a public resolver, in scenarios where the attacker can keep a concurrent query window alive, the attacker can first filter the source port and then perform birthday-style guessing against the TXID, making cache poisoning a feasible attack path. | Thu 22 Oct |
| CVE-2026-96405 | 5.3 medium | 0.00% | no CPE yet | NLnet Labs Unbound up to and including version 1.26.1 limits compression-pointer traversal for each individual domain-name operation but has no aggregate inbound decompression-work budget. Many chained compression pointers in a message results in a lot of CPU usage following them. A malicious actor with recursive-query access and control of an ordinarily delegated authority that serves specially crafted replies can exploit the vulnerability and degrade Unbound's general performance. | Thu 22 Oct |
| CVE-2026-107447 | 5.3 medium | 0.00% | no CPE yet | The Contest Gallery WordPress plugin before 34.0.1 does not reliably validate the visitor identity used to enforce its one-vote-per-entry restriction, trusting a client-supplied request header and an unbound client-generated token, which allows unauthenticated users to bypass the restriction and cast multiple votes for the same contest entry, inflating its vote total. | 21 Oct |
| CVE-2026-56416 | 4.8 medium | 0.00% | nlnetlabs, unbound | In NLnet Labs Unbound up to and including version 1.25.1, when the validator builds the canonical RDATA form for an RRSIG-covered PX/RP/MINFO/SOA RRset, it computes the address of the second embedded domain name as 'datstart + dname_valid(datstart, ...)' and passes it straight to 'query_dname_tolower()' without checking that a second name is actually present in the RDATA. The wire-format parser accepts multi-dname RRs whose RDATA ends after the first name, so an attacker who runs a DNSSEC-signed authoritative server can deliver a record with an absent second domain name (e.g. SOA record) and cause 'query_dname_tolower()' to walk label-by-label through stale bytes in the per-worker 'env->scratch_buffer', past the end of that heap allocation if 'msg-buffer-size' has been lowered from the default. This leads to heap buffer overflow and on a release build the outcome relies heavily on the contents of the buffer tail and the adjacent heap chunk. | Sat 24 Oct |
| CVE-2022-50259 | 4.7 medium | 0.00% | linux, linux_kernel | In the Linux kernel, the following vulnerability has been resolved: bpf, sockmap: fix race in sock_map_free() sock_map_free() calls release_sock(sk) without owning a reference on the socket. This can cause use-after-free as syzbot found [1] Jakub Sitnicki already took care of a similar issue in sock_hash_free() in commit 75e68e5bf2c7 ("bpf, sockhash: Synchronize delete from bucket list on map free") [1] refcount_t: decrement hit 0; leaking memory. WARNING: CPU: 0 PID: 3785 at lib/refcount.c:31 refcount_warn_saturate+0x17c/0x1a0 lib/refcount.c:31 Modules linked in: CPU: 0 PID: 3785 Comm: kworker/u4:6 Not tainted 6.1.0-rc7-syzkaller-00103-gef4d3ea40565 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/26/2022 Workqueue: events_unbound bpf_map_free_deferred RIP: 0010:refcount_warn_saturate+0x17c/0x1a0 lib/refcount.c:31 Code: 68 8b 31 c0 e8 75 71 15 fd 0f 0b e9 64 ff ff ff e8 d9 6e 4e fd c6 05 62 9c 3d 0a 01 48 c7 c7 80 bb 68 8b 31 c0 e8 54 71 15 fd <0f> 0b e9 43 ff ff ff 89 d9 80 e1 07 80 c1 03 38 c1 0f 8c a2 fe ff RSP: 0018:ffffc9000456fb60 EFLAGS: 00010246 RAX: eae59bab72dcd700 RBX: 0000000000000004 RCX: ffff8880207057c0 RDX: 0000000000000000 RSI: 0000000000000201 RDI: 0000000000000000 RBP: 0000000000000004 R08: ffffffff816fdabd R09: fffff520008adee5 R10: fffff520008adee5 R11: 1ffff920008adee4 R12: 0000000000000004 R13: dffffc0000000000 R14: ffff88807b1c6c00 R15: 1ffff1100f638dcf FS: 0000000000000000(0000) GS:ffff8880b9800000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000001b30c30000 CR3: 000000000d08e000 CR4: 00000000003506f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> __refcount_dec include/linux/refcount.h:344 [inline] refcount_dec include/linux/refcount.h:359 [inline] __sock_put include/net/sock.h:779 [inline] tcp_release_cb+0x2d0/0x360 net/ipv4/tcp_output.c:1092 release_sock+0xaf/0x1c0 net/core/sock.c:3468 sock_map_free+0x219/0x2c0 net/core/sock_map.c:356 process_one_work+0x81c/0xd10 kernel/workqueue.c:2289 worker_thread+0xb14/0x1330 kernel/workqueue.c:2436 kthread+0x266/0x300 kernel/kthread.c:376 ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:306 </TASK> | 15 Oct |
| CVE-2026-41637 | 3.7 low | 0.00% | nlnetlabs, unbound | In NLnet Labs Unbound 1.22.0 up to and including 1.25.1, client terminated DNS-over-QUIC (DoQ) queries are not accounted properly by Unbound resulting in low-cost inflation of the waiting number of replies for already in-flight resolution queries. This results in degradation of resolution service for new clients for already in-flight queries. A malicious actor can exploit the vulnerability by issuing DoQ queries for query names that need resolution and proceeding on immediately terminating the query by one of STOP_SENDING/RESET_STREAM/CONNECTION_CLOSE QUIC frames. Those terminated DoQ queries are not properly counted for and keep inflating the number of waiting replies for in-flight queries. When the maximum is reached, it results in silent query drops for new clients needing resolution for already in-flight queries. This vulnerability needs Unbound to be compiled with DoQ support ('--with-libngtcp2') and the 'quic-port' to be configured for the listening interfaces. Additionally, a malicious actor needs access to multiple source IPs to bypass the by-default configured 'wait-limit' option. | Sat 24 Oct |
| CVE-2026-42955 | 3.7 low | 0.00% | nlnetlabs, unbound | In NLnet Labs Unbound 1.16.2 up to and including 1.25.1, a similar vulnerability as with CVE-2026-40622 in the 'ghost domain names' family of attacks was found in Unbound that could extend the ghost domain window by up to one cached TTL configured value for A/AAAA glue records. Similar to other 'ghost domain names' attacks, an adversary needs to control a (ghost) zone and be able to query a vulnerable Unbound. A single client A/AAAA query can cause Unbound to overwrite the cached expired parent-side glue rrset and essentially extend the ghost domain window by up to one cached TTL configured value ('cache-max-ttl'). In configurations where 'harden-referral-path: yes' is used (non-default configuration), no client query is required since Unbound implicitly performs that query. This is a variant of CVE-2026-40622 which only addressed the NS query. | Sat 24 Oct |
| CVE-2026-44687 | 3.7 low | 0.00% | nlnetlabs, unbound | In NLnet Labs Unbound 1.13.2 up to and including 1.25.1, stub or forward zones where the name is below an intermediate labed below a DNSSEC signed zone could be shadowed by the intermediate label's secure NXDOMAIN answer from the parent. This is caused by an off-by-one error in 'harden-below-nxdomain' logic; enabled by default. It effectively bypasses the configuration and the configured stub/forward zone is never contacted. 'harden-below-nxdomain' does an upward DNS cache walk together with a delegation point guard that does not allow NXDOMAIN synthesis above stub/forward zones. The guard tests the domain name but before stripping a label. This results in an iteration where the domain name equals the configured stub/forward zone apex that passes the guard, strips one more label, and probes the cache at the apex's immediate public parent. If that parent has a cached DNSSEC-secure NXDOMAIN, which it will for any private namespace nested two or more labels under a signed public name, the walk returns it and the configured stub/forward upstream is never contacted. This can only be triggered by the query for the intermediate label (between the stub/forward apex and the DNSSEC parent zone). | Sat 24 Oct |
| CVE-2026-46582 | 3.7 low | 0.00% | nlnetlabs, unbound | In NLnet Labs Unbound 1.6.0 up to and including 1.25.1, a replay of a wildcard rrset as another piece of data, could be briefly considered DNSSEC secure based only on the RRSIG validation and stored into cache, before later validation treats it as bogus based on NSEC validation. When the resolving thread puts secure on the rrset, and another thread that is on the serve expired path then picks up the updated rrset contents with the secure status for a reply, it can be used to change a specific record, next to a wildcard that could be covered by the wildcard, into the wildcard. A malicious actor can exploit the possible poisonous effect by having any DNSSEC-singed domain (irrelevant to the victim domain) and a CNAME wrapper record that points to a record next to a wildcard (that could be covered by the wildcard). Then quering Unbound for the wildcard sibling record would seed the secure message. A later (after expiry) query for the CNAME wrapper would need to resolve the target sibling record. If the wildcard replay is injected into the response, the wildcard rrset will update the expired sibling record with a secure status before completing proper wildcard validation with NSEC records and eventually treating the CNAME wrapper answer as bogus. The updated poisoned rrset is now secure and points to the wildcard. This vulnerability is explicit for the serve expired path and needs injection of the signed wildcard rrset without the NSEC accompanying rrset. | Sat 24 Oct |
| CVE-2026-54478 | 3.7 low | 0.00% | nlnetlabs, unbound | In NLnet Labs Unbound 1.18.0 up to and including 1.25.1, when Unbound listens on a 'proxy-protocol-port' interface with 'answer-cookie: yes', the RFC 9018 server-cookie SipHash is computed over the proxy's wire address instead of the PROXYv2-declared client. One server cookie obtained through a given proxy node therefore validates for every PROXYv2-declared source behind that node. On a UDP+proxy-protocol front, an off-path attacker can harvest one cookie with a single legitimate query, then replay it under any spoofed source and pass DNS Cookie checks that were deployed to defeat this in the first place. | Sat 24 Oct |
| CVE-2026-35501 | 3.7 low | 0.00% | no CPE yet | When NLnet Labs Unbound 1.0.1 up to and including version 1.26.1 is configured with both a root trust anchor and an additional 'trust-anchor:' for an island-of-security zone whose parent is provably insecure under the root chain, a malicious actor with a forged NSEC reply with the SOA bit cleared can trick Unbound to treat the configured trust island as insecure. This happens because the DNSSEC validator in Unbound accepts and caches the NSEC insecure response bypassing the RRSIG validation that the validator was supposed to do. The acceptance of the NSEC record at the trust anchor apex was allowed due to and old fix for type DS and NSEC queries from clients when trust anchor for that name existed. | Thu 22 Oct |
| CVE-2026-55708 | 3.1 low | 0.00% | nlnetlabs, unbound | In NLnet Labs Unbound 1.6.0 up to and including 1.25.1, the 'view_local_data' and 'view_local_datas' commands of 'unbound-control' create a bare local zones tree for an already configured named view when the view is configured with no local data to begin with. However, the creation through the control interface omits adding the default-protected zones (e.g., RFC 1918 reverse, AS112 zones, .onion, .localhost). Once the local zone tree exists without the defaults, every query for a default-protected name from a client mapped to that view escapes to the public DNS via the iterator instead of being answered locally, bypassing local policy expectations. | Sat 24 Oct |
| CVE-2026-99103 | unscored | — | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: workqueue: Fix unbound pool lifetime for pending pwqs KASAN reports a use-after-free of an unbound worker_pool in node_activate_pending_pwq(): BUG: KASAN: slab-use-after-free in _raw_spin_trylock+0x6d/0x120 Read of size 4 at addr ffff8880089ce000 by task kworker/u22:0/318 CPU: 1 UID: 0 PID: 318 Comm: kworker/u22:0 Not tainted 7.2.0 #1 PREEMPT(lazy) Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014 Workqueue: 0x0 (flush-8:0) Call Trace: <TASK> dump_stack_lvl+0x53/0x70 print_report+0xce/0x610 kasan_report+0xce/0x100 _raw_spin_trylock+0x6d/0x120 pwq_dec_nr_in_flight+0x4b4/0xcb0 process_one_work+0x921/0x11a0 worker_thread+0x4d0/0xd20 kthread+0x2de/0x3c0 ret_from_fork+0x3aa/0x620 ret_from_fork_asm+0x1a/0x30 </TASK> Allocated by task 311: alloc_pwq+0x439/0xca0 apply_wqattrs_prepare+0x75e/0xd10 apply_workqueue_attrs_locked+0x44/0xa0 wq_nice_store+0x350/0x450 Freed by task 0: kfree+0x127/0x3b0 rcu_core+0x523/0x1780 handle_softirqs+0x1b3/0x610 Last potentially related work creation: put_unbound_pool+0x3f3/0x7d0 pwq_release_workfn+0x494/0x8e0 kthread_worker_fn+0x1ff/0x790 Canceling the last inactive work skips pwq_dec_nr_active(), so an empty pwq can remain on pending_pwqs when its refcnt reaches zero. pwq_release_workfn() currently puts the pool before removing that pwq. If this drops the last pool reference, the pool can be RCU-freed while the pwq remains reachable, and node_activate_pending_pwq() may trylock the freed pool->lock. Remove the pwq from pending_pwqs before putting the pool. | 21 h ago |
| CVE-2026-98859 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: HID: multitouch: stop the release timer from being rearmed on remove mt_remove() quiesces the sticky-finger timer before stopping the hardware: timer_delete_sync(&td->release_timer); sysfs_remove_group(&hdev->dev.kobj, &mt_attribute_group); hid_hw_stop(hdev); timer_delete_sync() waits for a running callback and dequeues the timer, but it does not stop the timer from being armed again. The transport is still delivering reports at that point, and the report path rearms it: if (app->quirks & MT_QUIRK_STICKY_FINGERS) { if (td->mt_io_flags & MT_IO_SLOTS_MASK) mod_timer(&td->release_timer, jiffies + msecs_to_jiffies(100)); A report that arrives after timer_delete_sync() has returned therefore leaves the timer queued. td is allocated with devm_kzalloc() against hdev->dev, so it is freed when the driver is unbound, after mt_remove() returns. When the timer fires afterwards, mt_expired_timeout() dereferences the freed td: struct mt_device *td = timer_container_of(td, t, release_timer); struct hid_device *hdev = td->hdev; if (test_and_set_bit_lock(MT_IO_FLAGS_RUNNING, &td->mt_io_flags)) Simply moving the teardown after hid_hw_stop() does not fix this on its own, because mt_expired_timeout() calls mt_release_contacts(), which walks hdev->inputs; the timer still has to be quiesced before hid_hw_stop() tears the input devices down. Use timer_shutdown_sync() instead, which additionally makes any later mod_timer() a no-op, so neither ordering constraint has to be traded off against the other. This is the final-teardown pattern the function was introduced for, and hid-wiimote already uses it for the same reason. | 21 Oct |
| CVE-2026-98782 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: drm/mediatek: Fix ovl adaptor platform device leak mtk_drm_probe() creates an OVL adaptor platform device with platform_device_register_data() when the display pipeline requires the OVL adaptor. If a later initialization step fails, the probe error path releases the DRM resources without unregistering the already registered OVL adaptor device. The normal remove path likewise leaves the device registered after the DRM driver is unbound. Keep track of whether the OVL adaptor was successfully registered and unregister it on probe failure. Also recover the platform device from the stored DDP component device and unregister it during normal removal. The issue was identified by a static analysis tool I developed and confirmed by manual review. | 21 Oct |
| CVE-2026-98757 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: usb: cdns3: fix use-after-free in cdns3_gadget_exit() cdns3_gadget_start() arms two works on system_freezable_wq: pending_status_wq for the deferred ep0 status stage and aligned_buf_wq for realigned request buffers. Both handlers use the cdns3_device the works are embedded in, and cdns3_pending_setup_status_handler() also calls the ep0 request completion. cdns3_gadget_exit() does not wait for these works. It frees all endpoints and aligned buffers and drops the last reference to the gadget device, which frees priv_dev, so a work queued before the exit can run after the free. Fix this by waiting for both works after the gadget driver is unbound and the IRQ is freed, when no new work can be queued, and before the endpoints and buffers are released. This issue was found by an in-house static analysis tool. | 21 Oct |
| CVE-2026-98749 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: tty: serial: max3100: shut down timer before freeing port max3100_shutdown() stops the polling timer but returns early during system suspend. If the SPI device is unbound before resume, the serial core does not call max3100_shutdown() again, so max3100_remove() frees the port while the timer remains armed. max3100_timeout() may then access the freed port and re-arm the timer. Add final timer teardown to max3100_remove() and use timer_shutdown_sync() to prevent a racing callback from re-arming it. Also free the IRQ and destroy the workqueue there before freeing the port. Keep timer_delete_sync() in max3100_shutdown() so that a subsequent open() can re-arm the timer. The workqueue is created before request_irq() and destroyed on both request_irq() failure and normal shutdown. Its presence at remove thus identifies the IRQ left registered when suspend bypasses shutdown. Free the IRQ before destroying the workqueue, in both max3100_shutdown() and max3100_remove(), and cancel the pending work in between. free_irq() waits for a running interrupt handler to finish and no new handler can start afterwards, so a racing handler cannot queue work on a workqueue that is being destroyed; the force_end_work check in max3100_dowork() only narrows that window, as a handler delayed between the check and queue_work() could still run after the teardown has cleared the workqueue pointer. Cancelling the work also keeps destroy_workqueue() from waiting on a queued work item in case remove() ever runs while the freezable workqueue is still frozen, e.g. device removal during the resume window, before workqueues are thawed. This issue was found by an in-house static analysis tool. | 21 Oct |
| CVE-2026-98043 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: bpf: Don't infer non-NULL from a pointer with an unbounded offset reg_not_null() decides that a register holds a non-NULL value by looking at its type alone. For pointer types that allow arithmetic the type only guarantees a non-NULL base, in case of an unbound offset the runtime offset value might still add up to NULL. Consider the followng program: r6 = bpf_map_lookup_elem(map, &0); /* present */ if (r6 == 0) return 0; r7 = bpf_map_lookup_elem(map, &1); /* absent, NULL at runtime */ r8 = r7; r8 -= r6; /* pointer - pointer: unknown scalar, -r6 */ r8 <<= 1; r8 >>= 1; /* any non-negative offset is accepted by */ /* check_reg_sane_offset_ptr() */ r6 += r8; /* verifier: map value; runtime: zero */ if (r7 != r6) return 0; *(u8 *)(r7 + 0); /* r7 is inferred non-NULL, both are zero */ At runtime both registers are zero, the comparison is true and the load faults with NULL pointer dereference. Require the offset to be within +-BPF_MAX_VAR_OFF in reg_not_null(). | 21 Oct |
| CVE-2026-97479 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: driver core: Avoid warning when removing a device while its supplier is unbinding During driver removal, the following warning can appear: WARNING: CPU: 1 PID: 139 at drivers/base/core.c:1497 __device_links_no_driver+0xcc/0xfc ... Call trace: __device_links_no_driver+0xcc/0xfc (P) device_links_driver_cleanup+0xa8/0xf0 device_release_driver_internal+0x208/0x23c device_links_unbind_consumers+0xe0/0x108 device_release_driver_internal+0xec/0x23c device_links_unbind_consumers+0xe0/0x108 device_release_driver_internal+0xec/0x23c device_links_unbind_consumers+0xe0/0x108 device_release_driver_internal+0xec/0x23c driver_detach+0xa0/0x12c bus_remove_driver+0x6c/0xbc driver_unregister+0x30/0x60 pci_unregister_driver+0x20/0x9c lan966x_pci_driver_exit+0x18/0xa90 [lan966x_pci] This warning is triggered when a consumer is removed because the links status of its supplier is not DL_DEV_DRIVER_BOUND and the link flag DL_FLAG_SYNC_STATE_ONLY is not set. The topology in terms of consumers/suppliers used was the following (consumer ---> supplier): i2c -----------> OIC ----> PCI device | ^ | | +---> pinctrl ---+ When the PCI device is removed, the OIC (interrupt controller) has to be removed. In order to remove the OIC, pinctrl and i2c need to be removed and to remove pinctrl, i2c need to be removed. The removal order is: 1) i2c 2) pinctrl 3) OIC 4) PCI device In details, the removal sequence is the following (with 0000:01:00.0 the PCI device): driver_detach: call device_release_driver_internal(0000:01:00.0)... device_links_busy(0000:01:00.0): links->status = DL_DEV_UNBINDING device_links_unbind_consumers(0000:01:00.0): 0000:01:00.0--oic link->status = DL_STATE_SUPPLIER_UNBIND call device_release_driver_internal(oic)... device_links_busy(oic): links->status = DL_DEV_UNBINDING device_links_unbind_consumers(oic): oic--pinctrl link->status = DL_STATE_SUPPLIER_UNBIND call device_release_driver_internal(pinctrl)... device_links_busy(pinctrl): links->status = DL_DEV_UNBINDING device_links_unbind_consumers(pinctrl): pinctrl--i2c link->status = DL_STATE_SUPPLIER_UNBIND call device_release_driver_internal(i2c)... device_links_busy(i2c): links->status = DL_DEV_UNBINDING __device_links_no_driver(i2c)... pinctrl--i2c link->status is DL_STATE_SUPPLIER_UNBIND oic--i2c link->status is DL_STATE_ACTIVE oic--i2c link->supplier->links.status is DL_DEV_UNBINDING The warning is triggered by the i2c removal because the OIC (supplier) links status is not DL_DEV_DRIVER_BOUND. Its links status is indeed set to DL_DEV_UNBINDING. It is perfectly legit to have the links status set to DL_DEV_UNBINDING in that case. Indeed we had started to unbind the OIC which triggered the consumer unbinding and didn't finish yet when the i2c is unbound. Avoid the warning when the supplier links status is set to DL_DEV_UNBINDING and thus support this removal sequence without any warnings. | 21 Oct |
| CVE-2026-92482 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: pinctrl: mediatek: use devm_gpiochip_add_data() for GPIO chip The gpio_chip is allocated with device-managed memory but registered with the non-managed gpiochip_add_data(). This was harmless while the drivers were built-in, but once they can be built as modules and unbound/rmmod'd, devm frees the gpio_chip's memory while it is still registered, causing a use-after-free. Register it with devm_gpiochip_add_data() so it shares the same device-managed lifecycle, which also lets the manual gpiochip_remove() error paths go away. | 21 Oct |
| CVE-2026-90311 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: thermal: hwmon: Remove hwmon class device along with its parent The current code creates one hwmon device per thermal zone type and that device is registered under the first thermal zone of the given type. That turns out to be problematic when the thermal zone holding the hwmon device is removed. For example, say that there are two ACPI thermal zones on a system /sys/devices/virtual/thermal/thermal_zone0/ /sys/devices/virtual/thermal/thermal_zone1/ The current code registers a hwmon class device for thermal_zone0 only: /sys/devices/virtual/thermal/thermal_zone0/hwmon0/ because the type is "acpitz" for both of them, but it adds a sysfs attribute that belongs to thermal_zone1 under it: /sys/devices/virtual/thermal/thermal_zone0/hwmon0/temp2_input There is also /sys/devices/virtual/thermal/thermal_zone0/hwmon0/temp1_input which belongs to thermal_zone0. When thermal_zone0 is removed, say because the ACPI thermal driver is unbound from the underlying platform device, thermal_remove_hwmon_sysfs() skips the removal of hwmon0 because of the temp2_input attribute belonging to thermal_zone1 which effectively prevents thermal_zone0 removal from making progress. Address this by making thermal_remove_hwmon_sysfs() remove the entire hwmon class device interface for the given thermal zone type when the thermal zone device holding it is removed. To prevent races with thermal_add_hwmon_sysfs() that may interfere with this, carry out the entire addition and removal of hwmon sysfs interfaces for thermal zones under thermal_hwmon_list_lock. Also adjust the layout of the labels in thermal_add_hwmon_sysfs() to the current kernel coding style to align with the new "unlock" label. | 21 Oct |
| CVE-2026-90265 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: btrfs: defrag: fix deadlock between defrag and delalloc space reservation While running fsstress with autodefrag and flushoncommit, hit a deadlock due to the fact that defrag reserves delalloc space while it's holding dirty and locked folios, besides the extent range lock. The stack traces are the following: [958.624] task:kworker/u50:3 state:D stack:0 pid:20365 tgid:20365 ppid:2 task_flags:0x4208060 flags:0x00080000 [958.626] Workqueue: events_unbound btrfs_async_reclaim_metadata_space [btrfs] [958.627] Call Trace: [958.628] <TASK> [958.628] __schedule+0x4be/0x10f0 [958.629] ? preempt_count_add+0x69/0xa0 [958.630] schedule+0x26/0xd0 [958.631] wait_current_trans+0x102/0x160 [btrfs] [958.632] ? __pfx_autoremove_wake_function+0x10/0x10 [958.633] start_transaction+0x374/0x900 [btrfs] [958.634] btrfs_commit_current_transaction+0x1d/0x70 [btrfs] [958.635] flush_space+0xca/0x5e0 [btrfs] [958.636] ? _raw_spin_unlock+0x15/0x30 [958.637] ? btrfs_reduce_alloc_profile+0x8c/0x190 [btrfs] [958.639] ? _raw_spin_unlock+0x15/0x30 [958.640] ? calc_available_free_space.isra.0+0x6f/0x110 [btrfs] [958.641] do_async_reclaim_metadata_space+0x84/0x190 [btrfs] [958.642] btrfs_async_reclaim_metadata_space+0x64/0x80 [btrfs] [958.644] process_one_work+0x19d/0x3a0 [958.644] worker_thread+0x1c4/0x330 [958.645] ? __pfx_worker_thread+0x10/0x10 [958.646] kthread+0xfc/0x130 [958.647] ? __pfx_kthread+0x10/0x10 [958.648] ret_from_fork+0x1f7/0x2c0 [958.648] ? __pfx_kthread+0x10/0x10 [958.649] ret_from_fork_asm+0x1a/0x30 [958.650] </TASK> [958.651] task:kworker/u49:7 state:D stack:0 pid:52990 tgid:52990 ppid:2 task_flags:0x4208060 flags:0x00080000 [958.653] Workqueue: writeback wb_workfn (flush-btrfs-334) [958.655] Call Trace: [958.655] <TASK> [958.656] __schedule+0x4be/0x10f0 [958.657] ? __blk_flush_plug+0xe9/0x140 [958.658] schedule+0x26/0xd0 [958.658] io_schedule+0x42/0x70 [958.659] folio_wait_bit_common+0x12b/0x330 [958.660] ? folio_wait_bit_common+0x100/0x330 [958.662] ? __pfx_wake_page_function+0x10/0x10 [958.663] extent_write_cache_pages+0x599/0x830 [btrfs] [958.664] ? acpi_fwnode_get_reference_args+0x1fa/0x270 [958.665] btrfs_writepages+0x77/0x130 [btrfs] [958.666] ? __pfx_end_bbio_data_write+0x10/0x10 [btrfs] [958.667] do_writepages+0xc6/0x160 [958.668] __writeback_single_inode+0x42/0x310 [958.669] writeback_sb_inodes+0x231/0x570 [958.670] wb_writeback+0x8a/0x340 [958.671] wb_workfn+0xbf/0x450 [958.672] ? finish_task_switch.isra.0+0xc1/0x350 [958.673] process_one_work+0x19d/0x3a0 [958.673] worker_thread+0x1c4/0x330 [958.674] ? __pfx_worker_thread+0x10/0x10 [958.675] kthread+0xfc/0x130 [958.676] ? __pfx_kthread+0x10/0x10 [958.676] ret_from_fork+0x1f7/0x2c0 [958.677] ? __pfx_kthread+0x10/0x10 [958.678] ret_from_fork_asm+0x1a/0x30 [958.679] </TASK> [958.679] task:btrfs-cleaner state:D stack:0 pid:296750 tgid:296750 ppid:2 task_flags:0x208040 flags:0x00080000 [958.681] Call Trace: [958.682] <TASK> [958.682] __schedule+0x4be/0x10f0 [958.683] schedule+0x26/0xd0 [958.684] handle_reserve_ticket+0x1b9/0x2c0 [btrfs] [958.685] ? __pfx_autoremove_wake_function+0x10/0x10 [958.686] reserve_bytes+0x283/0x4c0 [btrfs] [958.687] btrfs_reserve_metadata_bytes+0x18/0xb0 [btrfs] [958.688] btrfs_delalloc_reserve_metadata+0x121/0x320 [btrfs] [958.690] btrfs_delalloc_reserve_space+0x46/0xb0 [btrfs] [958.691] btrfs_defrag_file+0x903/0x1110 [btrfs] [958.692] btrfs_run_defrag_inodes+0x334/0x430 [btrfs] [958.694] cleaner_kthread+0x97/0x1c0 [btrfs] [958.694] ? __pfx_cleaner_kthread+0x10/0x10 [btrfs] [958.696] kthread+0xfc/0x130 [958.696] ? __pfx_kthread+0x10/0x10 [958.697] ret_ ---truncated--- | 21 Oct |
| CVE-2026-89625 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: HID: sony: fix UAF of ghl_poke_timer / ghl_urb at driver unbind For GHL (Guitar Hero Live) dongles, sony_probe() arms a periodic timer: ghl_magic_poke() (the timer callback) submits sc->ghl_urb, and the URB completion ghl_magic_poke_cb() re-arms the timer with mod_timer(). sony_remove() drained the timer with timer_delete_sync() and then freed the URB with usb_free_urb(): timer_delete_sync(&sc->ghl_poke_timer); usb_free_urb(sc->ghl_urb); timer_delete_sync() does not block re-arming, and while the URB is in flight the timer is not pending, so the sync delete is a no-op. A URB completion that runs after the delete re-arms the timer, and usb_free_urb() only drops a reference -- it does not kill an in-flight URB. sc is allocated with devm_kzalloc() and freed once sony_remove() returns, so the re-armed ghl_poke_timer (embedded in sc) then fires on freed memory, a use-after-free from timer softirq. This is a disconnect/rmmod race. Poison the URB first, then shut the timer down, before freeing the URB. usb_poison_urb() kills any in-flight URB and permanently rejects further submissions, so a poke timer that is still pending cannot re-submit the URB from ghl_magic_poke() in the window before timer_shutdown_sync() runs. usb_kill_urb() would not suffice: it only cancels the in-flight URB and leaves it submittable once it returns, so the pending timer could re-submit it and put a fresh URB in flight over the freed sc. timer_shutdown_sync() then drains any last callback and blocks re-arming. The probe error path is unaffected: it is only reached before the timer is armed. Reproduced under KASAN on next-20260710 via dummy_hcd + raw-gadget emulation of the GHL PS4 dongle (VID 0x1430 / PID 0x07bb): hid-sony binds and arms the poke timer, the poke URB is held in flight, the driver is unbound (freeing sc), then the URB is released. The completion re-arms the timer on the freed sc, and the re-armed timer fires ~8 s later: BUG: KASAN: slab-use-after-free in ghl_magic_poke+0x98/0xb0 Read of size 8 at addr ffff88810b02fd50 by task swapper/0/0 ghl_magic_poke+0x98/0xb0 call_timer_fn+0x35/0x2b0 __run_timers+0x69c/0x9a0 run_timer_softirq+0x173/0x2a0 Allocated by task 169: sony_probe Freed by task 338: devres_release_group <- hid_device_remove (sony_remove) Found by 0sec (https://0sec.ai) using automated source analysis. | 21 Oct |
| CVE-2025-40196 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: fs: quota: create dedicated workqueue for quota_release_work There is a kernel panic due to WARN_ONCE when panic_on_warn is set. This issue occurs when writeback is triggered due to sync call for an opened file(ie, writeback reason is WB_REASON_SYNC). When f2fs balance is needed at sync path, flush for quota_release_work is triggered. By default quota_release_work is queued to "events_unbound" queue which does not have WQ_MEM_RECLAIM flag. During f2fs balance "writeback" workqueue tries to flush quota_release_work causing kernel panic due to MEM_RECLAIM flag mismatch errors. This patch creates dedicated workqueue with WQ_MEM_RECLAIM flag for work quota_release_work. ------------[ cut here ]------------ WARNING: CPU: 4 PID: 14867 at kernel/workqueue.c:3721 check_flush_dependency+0x13c/0x148 Call trace: check_flush_dependency+0x13c/0x148 __flush_work+0xd0/0x398 flush_delayed_work+0x44/0x5c dquot_writeback_dquots+0x54/0x318 f2fs_do_quota_sync+0xb8/0x1a8 f2fs_write_checkpoint+0x3cc/0x99c f2fs_gc+0x190/0x750 f2fs_balance_fs+0x110/0x168 f2fs_write_single_data_page+0x474/0x7dc f2fs_write_data_pages+0x7d0/0xd0c do_writepages+0xe0/0x2f4 __writeback_single_inode+0x44/0x4ac writeback_sb_inodes+0x30c/0x538 wb_writeback+0xf4/0x440 wb_workfn+0x128/0x5d4 process_scheduled_works+0x1c4/0x45c worker_thread+0x32c/0x3e8 kthread+0x11c/0x1b0 ret_from_fork+0x10/0x20 Kernel panic - not syncing: kernel: panic_on_warn set ... | 19 Oct |
| CVE-2026-98839 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: vt: selection: Fix unsigned underflow and slab-out-of-bounds read in paste_selection() In paste_selection(), the loop copies min_t(unsigned int, vc_sel.buf_len - pasted,tty->receive_room) bytes per iteration into tty_ldisc_receive_buf() and increments pasted += count. Because the selection mutex (vc_sel.lock) is dropped inside the loop Whenever the line discipline buffer fills up and paste_selection() sleeps on tty->write_wait, a concurrent TIOCLINUX (TIOCL_SETSEL) ioctl can replace vc_sel.buffer with a shorter selection and reduce vc_sel.buf_len below pasted. When paste_selection() resumes, vc_sel.buf_len - pasted underflows as an unsigned integer to a large positive value, causing tty_ldisc_receive_buf(ld, vc_sel.buffer + pasted, NULL, count) to read up to 4094 bytes out-of-bounds past the newly allocated vc_sel.buffer. Fix this by terminating the loop when pasted >= vc_sel.buf_len. Kernel stack trace (Linux 7.3.0-rc3): ================================================================== BUG: KASAN: slab-out-of-bounds in n_tty_receive_buf_common+0xa01/0x1650 Read of size 4094 at addr ffff888101c58010 by task kworker/u17:1/65 Workqueue: events_unbound flush_to_ldisc Call Trace: <TASK> dump_stack_lvl+0x70/0xa0 print_report+0x153/0x4c6 kasan_report+0xf1/0x120 kasan_check_range+0x11c/0x200 __asan_memcpy+0x29/0x70 n_tty_receive_buf_common+0xa01/0x1650 tty_ldisc_receive_buf+0x66/0x110 tty_port_default_receive_buf+0x6b/0xb0 flush_to_ldisc+0x1b4/0x410 process_one_work+0x6ff/0x1110 worker_thread+0x4a8/0xb70 kthread+0x307/0x3e0 ret_from_fork+0x3ed/0x680 </TASK> ================================================================== | 19 Oct |
| CVE-2026-98813 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: bpf: Hold map BTF for the memory allocator destructor record bpf_ma_set_dtor() duplicates map->record so that the bpf_mem_alloc destructor can release the special fields of hash and rhash map elements once the allocator frees them for good. btf_record_dup() only acquires references on kernel and module BTF. Fields whose types live in the map BTF keep pointing into it: a kptr to a local type refers to map->btf, and a list_head or rb_root field carries a value_rec owned by the struct meta table of map->btf. That borrowed state can outlive the map. When RCU callbacks are still in flight, bpf_mem_alloc_destroy() copies the allocator and defers the final drain, together with the destructor context, to a workqueue. bpf_map_free() then frees map->record and drops the map's BTF reference as soon as map_free() returns. Once the program that loaded the BTF is gone as well, the BTF is freed while the worker still uses the duplicate. The worker dereferences it through btf_is_kernel() and btf_find_struct_meta() in bpf_obj_free_fields() when destroying elements that were freed under RCU, and through btf_is_kernel() in btf_record_free() when releasing the context itself: BUG: KASAN: slab-use-after-free in btf_is_kernel+0x19/0x30 Read of size 1 at addr ffff88811505dce8 by task kworker/u16:2/50 Workqueue: events_unbound free_mem_alloc_deferred Call Trace: btf_is_kernel+0x19/0x30 btf_record_free+0xc7/0xf0 htab_dtor_ctx_free+0x1a/0x30 free_mem_alloc_no_barrier+0x39/0x230 free_mem_alloc_deferred+0x2a/0x40 process_scheduled_works+0x5ce/0x9d0 worker_thread+0x42a/0x5e0 kthread+0x1f5/0x230 ret_from_fork+0x1dd/0x390 ret_from_fork_asm+0x1a/0x30 Allocated by task 358: __kmalloc_cache_noprof+0x287/0x510 btf_new_fd+0xf7/0x3d0 __sys_bpf+0x487/0x840 Freed by task 0: kfree+0x186/0x560 rcu_core+0x6f6/0xd40 Freeing a map that still holds more elements than the allocator's high watermark is enough to get there, because the bulk free during teardown queues the RCU callback that makes bpf_mem_alloc_destroy() defer. Non-preallocated hash maps and resizable hash maps both register the destructor and are affected alike. Keep one reference on the map BTF in the destructor context. Every non-kernel pointer in the duplicated record is either map->btf or memory owned by it, so a single reference covers kptrs, list heads, and rb roots, and mirrors what bpf_map_meta_alloc() does for the duplicated record of an inner map. Release it only after the duplicated record has been freed: the worker is preemptible and not in an RCU read-side critical section, so dropping the last reference first would let the BTF be freed while btf_record_free() still reads its fields. | 19 Oct |
| CVE-2026-98337 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: wifi: mac80211: don't start a ROC while scanning The ROC work can be pending when a scan starts (which requires ROC list to be empty, but that's possible), and then a new ROC can be added to the list and the work will pick it up. Avoid starting that ROC if a scan made it between things, as otherwise we'll hit a warning later: WARNING: net/mac80211/offchannel.c:404 at ieee80211_start_next_roc+0x256/0x2d0 Workqueue: events_unbound cfg80211_wiphy_work Call Trace: __ieee80211_scan_completed+0x4fd/0xe40 net/mac80211/scan.c:537 ieee80211_scan_work+0x472/0x1ff0 net/mac80211/scan.c:1193 cfg80211_wiphy_work+0x410/0x570 net/wireless/core.c:513 | 19 Oct |
| CVE-2026-98306 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: seg6: set IPSKB_L3SLAVE from IP6SKB_L3SLAVE on IPIP decapsulation When an SRv6 packet arrives on an interface enslaved to a VRF, vrf_ip6_rcv() sets IP6SKB_L3SLAVE in IP6CB, but decap_and_validate() has never set IPSKB_L3SLAVE in IPCB. The bit stayed clear in the common case, and with CONFIG_IPV6_MIP6 the leftover frag_max_size of a reassembled outer packet could even set it, with no VRF involved. Commit 44930446dde4 ("ipv6: seg6: clear IPv4 control block on IPIP decapsulation") then made the unreliable bit reliably clear. The effect of the missing flag is visible with End.DX4 when a delivery to a local address of the node reaches the socket lookup. For example, a UDP socket bound to the enslaved ingress interface does not receive any of the decapsulated packets, while an unbound socket outside the VRF does. This contradicts Documentation/networking/vrf.rst: by default the scope of an unbound UDP or TCP socket is limited to the default VRF. Set IPSKB_L3SLAVE for IPv4 in decap_and_validate(), which already does the same for IPv6. The socket lookup then matches the decapsulated packet like any other packet received on that enslaved interface. Such a packet matches an unbound UDP or TCP socket only when udp_l3mdev_accept or tcp_l3mdev_accept is set. | 19 Oct |
| CVE-2026-98235 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: net/sched: act_api: release tail references on DELACTION failure A batched RTM_DELACTION request takes a temporary reference on each action before attempting any deletion. tcf_action_delete() clears each processed slot and drops its temporary reference before attempting the deletion. If deletion fails, tca_action_gd() calls tcf_action_put_many() to release the remaining references, but its tcf_act_for_each_action() iterator stops at the first NULL slot. When a batch stops at an action bound to a filter, this leaks a reference on each subsequent action. A later delete of an unbound action can then return success without removing it from the IDR. Walk the full array in tcf_action_put_many() and skip NULL slots to release the references held on the unprocessed actions. | 19 Oct |
| CVE-2026-98202 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: Input: synaptics-rmi4 - fix GPF in suspend and resume when unbound Transport drivers (such as rmi_i2c and rmi_spi) invoke rmi_driver_suspend() and rmi_driver_resume() on their child rmi_dev device during system power management events. However, transport drivers are fully registered and operational even if the physical RMI driver failed to bind or probe the rmi_dev device. When rmi_driver_suspend() or rmi_driver_resume() is called on an unbound rmi_dev, dev_get_drvdata() returns NULL. Calling rmi_disable_irq() or rmi_enable_irq() without driver data attached causes a NULL pointer dereference and General Protection Fault when attempting to lock data->enabled_mutex. Fix this by checking if driver data is attached to rmi_dev in rmi_driver_suspend() and rmi_driver_resume(), exiting early if no driver data is present. | 19 Oct |
| CVE-2026-97995 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: virtio_console: do not free control-out buffers on remove __send_control_msg() publishes &portdev->cpkt as the control-out virtqueue cookie. remove_vqs() walks every virtqueue and passes leftover cookies to free_buf(), which treats them as struct port_buffer and reads sgpages. If a control message is still on c_ovq when the device is unbound, free_buf() reads past the ports_device object. KASAN reported slab-out-of-bounds in free_buf(): free_buf remove_vqs virtcons_remove unbind_store The object was the ports_device allocated in virtcons_probe(). Drain c_ovq without freeing. The packet lives in portdev and is released with it. | 19 Oct |
| CVE-2026-93183 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: drm/lima: call drm_mm_init() with a valid allocation range lima_vm_create() is currently run before va_start and va_end are set up, meaning they are both 0. lima_vm_create() runs drm_mm_init() with them as arguments for the allocator, and if DRM_DEBUG_MM is enabled the DRM_MM_BUG_ON check in drm_mm_init then fires, as seen here on exynos4412-odroid-u2: [ 1.736297] ------------[ cut here ]------------ [ 1.740370] kernel BUG at drivers/gpu/drm/drm_mm.c:931! [ 1.745574] Internal error: Oops - BUG: 0 [#1] SMP ARM [ 1.750697] Modules linked in: [ 1.753734] CPU: 0 UID: 0 PID: 41 Comm: kworker/u16:1 Not tainted 7.0.10-postmarketos-exynos4 #11 PREEMPT [ 1.763372] Hardware name: Samsung Exynos (Flattened Device Tree) [ 1.769446] Workqueue: events_unbound deferred_probe_work_func [ 1.775261] PC is at drm_mm_init+0x9c/0xa4 [ 1.779339] LR is at lima_vm_create+0x144/0x17c [ ... ] Fix the issue by moving the lima_vm_create() call after va_start and va_end are set up. | 19 Oct |
| CVE-2026-93145 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: clk: qcom: gdsc: tear down per-domain genpds in gdsc_unregister() gdsc_unregister() removes the OF provider entry and tears down the parent/subdomain wiring, but never calls pm_genpd_remove() on the individual generic_pm_domain structures registered by gdsc_init(): void gdsc_unregister(struct gdsc_desc *desc) { struct device *dev = desc->dev; size_t num = desc->num; gdsc_pm_subdomain_remove(desc, num); of_genpd_del_provider(dev->of_node); } That leaves dangling entries on the global gpd_list. After a provider unbind/rebind cycle (deferred-probe replay during early boot, real module unload of a clk driver that owns GDSCs, or an OF-overlay tear- down) the next gdsc_init() will end up trying to re-register a name that is still in the list and pm_genpd_init() returns -EEXIST. While we are here, flip the order so the consumer-facing OF provider entry is the first thing removed -- otherwise a fresh of_genpd_get_from_provider() call racing with the teardown could attach to a domain that is mid-removal. Iterate the scs[] array and pm_genpd_remove() each registered domain after the subdomain links are torn down. The regulators stay devm- managed (devm_regulator_get_optional() in gdsc_register()), so the release happens automatically when the underlying device is unbound; just the genpd accounting needs to be undone explicitly. | 19 Oct |
| CVE-2026-93084 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: firmware: arm_scmi: Drop handle on protocol bind failures The SCMI bus notifier acquires an SCMI handle when the driver core emits BUS_NOTIFY_BIND_DRIVER, before invoking the protocol driver probe callback. The protocol probe path only checks whether sdev->handle is set. If device_link_add() fails after the handle has been acquired, the protocol device can still bind with a valid handle but without the dependency link to the SCMI parent. A concurrent parent unbind can then miss the child and tear down the SCMI instance while the child still holds a handle into it. If the protocol driver probe later fails, for example with -EPROBE_DEFER, the driver core emits BUS_NOTIFY_DRIVER_NOT_BOUND rather than BUS_NOTIFY_UNBOUND_DRIVER. The SCMI notifier only released the handle on BUS_NOTIFY_UNBOUND_DRIVER, so each failed protocol-device bind leaked the SCMI instance users refcount and left sdev->handle set after the failed probe. Make the link helper report failure and drop the acquired handle if the link cannot be created. Also handle BUS_NOTIFY_DRIVER_NOT_BOUND in the same cleanup path used for unbind so failed probes balance the earlier BUS_NOTIFY_BIND_DRIVER acquisition. | 19 Oct |
| CVE-2026-92481 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: pinctrl: mediatek: free EINT resources on unbind mtk_eint_do_init() creates an IRQ domain, populates it with a mapping for every EINT line and installs a chained handler on the parent interrupt, but none of these are ever released. This was harmless while the drivers were built-in, but now that they can be built as modules and unbound/rmmod'd it leaves behind a dangling IRQ domain, interrupt mappings whose chip data points at freed memory, and a chained handler that keeps firing into that freed data. The plain allocations in mtk_eint_do_init() already use the device-managed devm_*() helpers, so tear the remaining resources down the same way: register a devm action that detaches the chained handler, waits for any in-flight handler to finish, disposes of the per-line mappings and removes the IRQ domain. This mirrors the device-managed lifecycle adopted for the GPIO chip and keeps the whole EINT setup self-cleaning on unbind. | 19 Oct |
| CVE-2026-90296 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: cpufreq: imx6q: fix devres accumulation across driver rebind imx6_soc_volt is allocated with devm_kcalloc(cpu_dev, ...), where cpu_dev is the CPU device from get_cpu_device(0). That device is never unbound, so its devres list is never released, and imx6q_cpufreq_remove() does not free the array either. Every probe therefore adds an allocation that stays for the lifetime of the system. Allocate against the platform device instead. Its devres is released when the driver is unbound, which is exactly the lifetime the array wants: imx6q_set_target() reads it, and nothing may reach that after cpufreq_unregister_driver(). That makes the array actually go away on unbind, so also clear the file-scope pointer in remove and on the failed-probe path, rather than leave it pointing at memory devres is about to release. Tested by rebinding the driver on qemu's mcimx6ul-evk. | 19 Oct |
| CVE-2026-90198 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: ALSA: core: Fix use-after-free in snd_card_do_free() A use-after-free was detected in snd_card_do_free() when a sound card managed by devres is unbound while a user-space application still holds an open file descriptor. For managed cards, the memory is allocated using devres_alloc(), and its release function is set to __snd_card_release(), which calls snd_card_free(). When the device is unbound, the unbind thread calls snd_card_free(), which drops a reference to the card's device. If the user thread still has an open file descriptor, the reference count does not reach zero, and the unbind thread blocks on wait_for_completion(&released). When the user thread closes the file descriptor, it drops the final reference, invoking the device release callback release_card_device(), which calls snd_card_do_free(). snd_card_do_free() performs cleanup and calls complete(card->release_completion). This wakes up the unbind thread, which returns from snd_card_free() and __snd_card_release(). The devres core then immediately frees the memory block containing the snd_card structure. Meanwhile, the user thread continues execution in snd_card_do_free() and evaluates `if (!card->managed)`. It reads the `managed` boolean from the snd_card structure that was just freed by the unbind thread, triggering a KASAN use-after-free. Fix this by caching the value of card->managed in a local variable before calling complete(). This ensures that the card pointer is not dereferenced after the unbind thread has been woken up and potentially freed the card. BUG: KASAN: use-after-free in snd_card_do_free sound/core/init.c:604 [inline] BUG: KASAN: use-after-free in release_card_device+0x1ab/0x1b0 sound/core/init.c:153 Read of size 1 at addr ffff8881912ec909 by task syz-executor130/5857 Call Trace: <TASK> dump_stack_lvl+0xe8/0x150 lib/dump_stack.c:120 print_address_description+0x55/0x1e0 mm/kasan/report.c:378 print_report+0x58/0x70 mm/kasan/report.c:482 kasan_report+0x117/0x150 mm/kasan/report.c:595 snd_card_do_free sound/core/init.c:604 [inline] release_card_device+0x1ab/0x1b0 sound/core/init.c:153 device_release+0xc4/0x1f0 drivers/base/core.c:-1 kobject_cleanup lib/kobject.c:689 [inline] kobject_release lib/kobject.c:720 [inline] kref_put include/linux/kref.h:65 [inline] kobject_put+0x222/0x550 lib/kobject.c:737 snd_card_file_remove+0x331/0x390 sound/core/init.c:1125 snd_pcm_release+0x12c/0x160 sound/core/pcm_native.c:2986 __fput+0x418/0xa50 fs/file_table.c:512 fput_close_sync+0x11f/0x240 fs/file_table.c:617 __do_sys_close fs/open.c:1511 [inline] __se_sys_close fs/open.c:1496 [inline] __x64_sys_close+0x7e/0x110 fs/open.c:1496 do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline] do_syscall_64+0x174/0x580 arch/x86/entry/syscall_64.c:94 entry_SYSCALL_64_after_hwframe+0x77/0x7f </TASK> | 19 Oct |
| CVE-2026-90126 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: rtc: pcf8563: fix clock provider leak on unbind pcf8563_clkout_register_clk() registers the CLKOUT clock provider with of_clk_add_provider(), but nothing ever unwinds it: there is no of_clk_del_provider() call and the driver has no remove callback. Each of_clk_add_provider() allocates a struct of_clk_provider, takes a reference on the OF node and adds an entry to the global of_clk_providers list, none of which is released when the device is unbound. Every bind/unbind (or module reload) therefore leaks a provider structure and an of_node reference. The clock itself is already device-managed (devm_clk_register()); only the provider registration was not. Use devm_of_clk_add_hw_provider() so the provider is removed automatically on unbind. Tie it to the parent i2c device, whose OF node carries the #clock-cells and clock-output-names properties (the RTC class device has no OF node of its own). | 19 Oct |
| CVE-2026-80999 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: net: dsa: realtek: use gpiod_set_value_cansleep for reset GPIO rtl83xx_reset_assert() and rtl83xx_reset_deassert() are only called from the probe path, which may sleep and is not timing-critical. When the reset GPIO is provided by a sleeping controller such as an I2C I/O expander, gpiod_set_value() warns: WARNING: drivers/gpio/gpiolib.c:4030 at gpiod_set_value+0x44/0x80, CPU#1: kworker/u16:4/61 Hardware name: B&O MAP CA33 Rev f (UNKNOWN) (DT) Workqueue: events_unbound deferred_probe_work_func pc : gpiod_set_value+0x44/0x80 lr : rtl83xx_probe+0x1d8/0x3a0 Call trace: gpiod_set_value+0x44/0x80 (P) rtl83xx_probe+0x1d8/0x3a0 realtek_mdio_probe+0x24/0xa0 mdio_probe+0x38/0x78 really_probe+0xc4/0x3e0 __driver_probe_device+0x15c/0x1b8 driver_probe_device+0xb4/0x120 __device_attach_driver+0xb8/0x1a0 bus_for_each_drv+0x88/0xf0 __device_attach+0xa0/0x1d8 device_initial_probe+0x54/0x68 bus_probe_device+0x38/0xa0 deferred_probe_work_func+0xb8/0x120 process_one_work+0x184/0x4e8 worker_thread+0x188/0x308 kthread+0x130/0x150 ret_from_fork+0x10/0x20 Switch both helpers to gpiod_set_value_cansleep() so such a reset GPIO can be used without triggering the warning. The reset GPIO has been driven with the non-sleeping gpiod_set_value() since the driver was added in v4.19. The call has since been refactored across several files - from realtek-smi.c / realtek-mdio.c into the common rtl83xx.c module and then into the rtl83xx_reset_assert() and rtl83xx_reset_deassert() helpers (both in v6.9). This patch therefore applies as-is only to kernels that carry those helpers (v6.9+); older stable kernels need the same gpiod_set_value_cansleep() conversion at the corresponding open-coded call sites. | 19 Oct |
97 of 97 · Previous
Download these 97 as CSV · subscribe to this list.
EPSS scores: 2026-10-28. NVD cursor: 2026-10-29 00:22. The News page shows only notable CVEs (KEV, your stack, new criticals, EPSS over 50%, or active exploitation per SSVC); this table has all of them.