Vulnerabilities
All
My stack
Known exploited
Public exploit
Critical (9+)
Likely exploited (EPSS ≥ 50%)
Changed, 24 h
New, 24 h
Sort:
risk
modified
published
CVSS
EPSS
| CVE | CVSS | EPSS | Vendor, product | Description | Modified |
|---|---|---|---|---|---|
| CVE-2026-43048 | 8.8 high | 0.00% | linux, linux_kernel | In the Linux kernel, the following vulnerability has been resolved: HID: core: Mitigate potential OOB by removing bogus memset() The memset() in hid_report_raw_event() has the good intention of clearing out bogus data by zeroing the area from the end of the incoming data string to the assumed end of the buffer. However, as we have previously seen, doing so can easily result in OOB reads and writes in the subsequent thread of execution. The current suggestion from one of the HID maintainers is to remove the memset() and simply return if the incoming event buffer size is not large enough to fill the associated report. Suggested-by Benjamin Tissoires <[email protected]> [bentiss: changed the return value] | 21 Oct |
| CVE-2026-90240 | 8.8 high | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: iommu/vt-d: Flush context cache with correct SID when tearing down aliases domain_context_clear_one() and device_pasid_table_teardown() are both invoked once per DMA alias of a device. Each function locates the context entry using the bus/devfn pair provided by the pci_for_each_dma_alias() callback, then calls intel_context_flush_no_pasid(), which constructs a device-selective context-cache invalidation from info->bus and info->devfn (that is, always the requester ID of the device itself). As a result, for every alias other than the device’s own RID, the context entry that was just cleared in memory is never invalidated in the context cache. Hardware may continue using that stale cached entry. In the scalable-mode teardown path, intel_pasid_free_table() can then free the PASID directory still referenced by that stale entry, allowing the IOMMU to walk freed memory. Fix this by passing the source ID of the entry being torn down to intel_context_flush_no_pasid(), instead of deriving it from @info. | 21 Oct |
| CVE-2026-89913 | 8.8 high | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: KVM: arm64: vgic-v3: take an LPI reference in vgic_v3_save_pending_tables vgic_v3_save_pending_tables() iterates dist->lpi_xa using xa_for_each() and dereferences the returned struct vgic_irq in the loop body without holding a reference on the LPI. The xarray iterator only provides temporary RCU coverage while looking up the current entry. That is not sufficient for this loop body, which reads fields from struct vgic_irq and performs guest memory accesses before the iteration completes. A concurrent path can trigger this race: the irqfd cached injection path (vgic_its_inject_cached_translation) obtains a transient LPI reference via vgic_its_check_cache() without holding kvm->lock, vcpu->mutex, config_lock, or its_lock. If guest ITS DISCARD then drops the cache and ITE references under its_lock, the transient inject reference may become the final one. When vgic_put_irq() drops it, the LPI is erased from lpi_xa and freed via kfree_rcu(). Meanwhile, vgic_v3_save_pending_tables() may still hold a stale pointer obtained from the xarray iterator and dereference it after the RCU grace period completes. Fix this by re-fetching each iterated LPI via vgic_get_irq(), which takes a stable reference, and dropping it with vgic_put_irq() on all paths. This matches the pattern already used by other lpi_xa iterators in the vgic ITS code. | 21 Oct |
| CVE-2026-89534 | 8.8 high | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: svcrdma: Clear sc_cm_id when ADDR_CHANGE replacement fails When svc_rdma_listen_handler() handles RDMA_CM_EVENT_ADDR_CHANGE, it creates a replacement listener cm_id and returns 1, telling the CM core to destroy the old one. If the replacement allocation fails, sc_cm_id still points at the old cm_id that the CM core is about to destroy. Any subsequent dereference of sc_cm_id -- such as svc_rdma_detach()'s rdma_disconnect() call -- is a use-after-free. NULL sc_cm_id on the failure path and guard svc_rdma_detach()'s rdma_disconnect() call against NULL so that the listener can be torn down safely when the server shuts down. | 21 Oct |
| CVE-2026-79609 | 8.8 high | 0.00% | no CPE yet | XPTI (Xen Page Table Isolation) was introduced to mitigate Meltdown (CVE-2017-5754, one aspect of XSA-254). This involves copying 64-bit PV guest page table entries from guest-chosen root page tables to the Xen- chosen one which is in actual use by hardware. To read the guest root page table, the directmap is used. PV guests, however, have a directmap which may not cover all memory; in particular this is the case if any memory extends beyond the 5 TiB (CONFIG_BIGMEM=y: 3.5 TiB) address boundary. | 20 Oct |
| CVE-2026-16753 | 8.8 high | 0.00% | no CPE yet | Incorrect authorization in the library-query execution endpoint in Lowcoder version, up to and including 2.4.10, allows an authenticated administrator or developer in one organization to execute a library query belonging to another organization via a crafted request containing the victim library-query identifier. | 20 Oct |
| CVE-2026-72061 | 8.8 high | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: net: sit: require CAP_NET_ADMIN in the device netns for changelink ipip6_changelink() operates on at most two netns, dev_net(dev) and the tunnel link netns t->net. They differ once the device is created in or moved to a netns other than the one the request runs in. The rtnl changelink path checks CAP_NET_ADMIN only against dev_net(dev), so a caller privileged there but not in t->net can rewrite a tunnel that lives in t->net. Gate ipip6_changelink() on rtnl_dev_link_net_capable() at its top, before any attribute is parsed. sit was the one tunnel type not covered by the recent series that added this check to the other changelink() handlers. | 19 Oct |
| CVE-2026-72055 | 8.8 high | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: net: ip6_vti: require CAP_NET_ADMIN in the device netns for changelink vti6_changelink() operates on at most two netns, dev_net(dev) and the tunnel link netns t->net. They differ once the device is created in or moved to a netns other than the one the request runs in. The rtnl changelink path checks CAP_NET_ADMIN only against dev_net(dev), so a caller privileged there but not in t->net can rewrite a tunnel that lives in t->net. Gate vti6_changelink() on rtnl_dev_link_net_capable() at its top, before any attribute is parsed. | 19 Oct |
| CVE-2026-72054 | 8.8 high | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: net: ip_vti: require CAP_NET_ADMIN in the device netns for changelink vti_changelink() operates on at most two netns, dev_net(dev) and the tunnel link netns t->net. They differ once the device is created in or moved to a netns other than the one the request runs in. The rtnl changelink path checks CAP_NET_ADMIN only against dev_net(dev), so a caller privileged there but not in t->net can rewrite a tunnel that lives in t->net. Gate vti_changelink() on rtnl_dev_link_net_capable() at its top, before any attribute is parsed. | 19 Oct |
| CVE-2026-72053 | 8.8 high | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: net: ipip: require CAP_NET_ADMIN in the device netns for changelink ipip_changelink() operates on at most two netns, dev_net(dev) and the tunnel link netns t->net. They differ once the device is created in or moved to a netns other than the one the request runs in. The rtnl changelink path checks CAP_NET_ADMIN only against dev_net(dev), so a caller privileged there but not in t->net can rewrite a tunnel that lives in t->net. Gate ipip_changelink() on rtnl_dev_link_net_capable() at its top, before any attribute is parsed. | 19 Oct |
| CVE-2026-72052 | 8.8 high | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: net: ip6_gre: require CAP_NET_ADMIN in the device netns for changelink ip6gre_changelink() and ip6erspan_changelink() operate on at most two netns, dev_net(dev) and the tunnel link netns t->net. They differ once the device is created in or moved to a netns other than the one the request runs in. The rtnl changelink path checks CAP_NET_ADMIN only against dev_net(dev), so a caller privileged there but not in t->net can rewrite a tunnel that lives in t->net. Gate both ops on rtnl_dev_link_net_capable() at their top, before any attribute is parsed. | 19 Oct |
| CVE-2026-72051 | 8.8 high | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: net: ip6_tunnel: require CAP_NET_ADMIN in the device netns for changelink ip6_tnl_changelink() operates on at most two netns, dev_net(dev) and the tunnel link netns t->net. They differ once the device is created in or moved to a netns other than the one the request runs in. The rtnl changelink path checks CAP_NET_ADMIN only against dev_net(dev), so a caller privileged there but not in t->net can rewrite a tunnel that lives in t->net. Gate ip6_tnl_changelink() on rtnl_dev_link_net_capable() at its top, before any attribute is parsed. | 19 Oct |
| CVE-2026-64434 | 8.8 high | 0.00% | linux, linux_kernel | In the Linux kernel, the following vulnerability has been resolved: Bluetooth: L2CAP: Fix UAF in channel timeout by holding conn ref l2cap_chan_timeout() runs asynchronously and accesses chan->conn. If the connection is torn down while the timer is running or pending, chan->conn can be freed, leading to a use-after-free when the timer worker attempts to lock conn->lock: | BUG: KASAN: slab-use-after-free in instrument_atomic_read_write include/linux/instrumented.h:112 [inline] | BUG: KASAN: slab-use-after-free in atomic_long_try_cmpxchg_acquire include/linux/atomic/atomic-instrumented.h:4456 [inline] | BUG: KASAN: slab-use-after-free in __mutex_trylock_fast kernel/locking/mutex.c:161 [inline] | BUG: KASAN: slab-use-after-free in mutex_lock+0x4f/0xa0 kernel/locking/mutex.c:318 | Write of size 8 at addr ffff8881298d9550 by task kworker/2:1/83 | | CPU: 2 UID: 0 PID: 83 Comm: kworker/2:1 Not tainted 7.1.0-rc6-next-20260601-dirty #6 PREEMPT(full) | Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.17.0-debian-1.17.0-1 04/01/2014 | Workqueue: events l2cap_chan_timeout | Call Trace: | <TASK> | instrument_atomic_read_write include/linux/instrumented.h:112 [inline] | atomic_long_try_cmpxchg_acquire include/linux/atomic/atomic-instrumented.h:4456 [inline] | __mutex_trylock_fast kernel/locking/mutex.c:161 [inline] | mutex_lock+0x4f/0xa0 kernel/locking/mutex.c:318 | l2cap_chan_timeout+0x5d/0x1b0 net/bluetooth/l2cap_core.c:422 | process_one_work kernel/workqueue.c:3326 [inline] | process_scheduled_works+0x7c8/0xfb0 kernel/workqueue.c:3409 | worker_thread+0x8a9/0xcf0 kernel/workqueue.c:3490 | kthread+0x346/0x430 kernel/kthread.c:436 | ret_from_fork+0x1a3/0x470 arch/x86/kernel/process.c:158 | ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:245 | </TASK> | | Allocated by task 320: | l2cap_conn_add+0xa7/0x820 net/bluetooth/l2cap_core.c:7075 | l2cap_connect_cfm+0xdb/0xd70 net/bluetooth/l2cap_core.c:7452 | hci_connect_cfm include/net/bluetooth/hci_core.h:2139 [inline] | hci_remote_features_evt+0x52f/0x9f0 net/bluetooth/hci_event.c:3760 | hci_event_func net/bluetooth/hci_event.c:7796 [inline] | hci_event_packet+0x561/0xa70 net/bluetooth/hci_event.c:7847 | hci_rx_work+0x370/0x890 net/bluetooth/hci_core.c:4040 | process_one_work kernel/workqueue.c:3326 [inline] | process_scheduled_works+0x7c8/0xfb0 kernel/workqueue.c:3409 | worker_thread+0x8a9/0xcf0 kernel/workqueue.c:3490 | kthread+0x346/0x430 kernel/kthread.c:436 | ret_from_fork+0x1a3/0x470 arch/x86/kernel/process.c:158 | ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:245 | | Freed by task 322: | hci_disconn_cfm include/net/bluetooth/hci_core.h:2154 [inline] | hci_conn_hash_flush+0x101/0x1f0 net/bluetooth/hci_conn.c:2736 | hci_dev_close_sync+0x889/0xde0 net/bluetooth/hci_sync.c:5405 | hci_dev_do_close net/bluetooth/hci_core.c:502 [inline] | hci_unregister_dev+0x1f7/0x370 net/bluetooth/hci_core.c:2679 | vhci_release+0x12a/0x180 drivers/bluetooth/hci_vhci.c:690 | __fput+0x369/0x890 fs/file_table.c:510 | task_work_run+0x160/0x1d0 kernel/task_work.c:233 | get_signal+0xf5b/0x1120 kernel/signal.c:2810 | arch_do_signal_or_restart+0x4d/0x600 arch/x86/kernel/signal.c:337 | __exit_to_user_mode_loop kernel/entry/common.c:64 [inline] | exit_to_user_mode_loop+0x85/0x510 kernel/entry/common.c:98 | do_syscall_64+0x263/0x3d0 arch/x86/entry/syscall_64.c:100 | entry_SYSCALL_64_after_hwframe+0x77/0x7f | | The buggy address belongs to the object at ffff8881298d9400 | which belongs to the cache kmalloc-512 of size 512 | The buggy address is located 336 bytes inside of | freed 512-byte region [ffff8881298d9400, ffff8881298d9600) Fix it by having chan->conn hold a reference to l2cap_conn (via l2cap_conn_get) when the channel is added to the connection, and releasing it in the channel destructor. This ensures the l2cap_conn remains alive as long as the channel exists. A new FLAG_DEL channel flag is introduced to indicate that the ch ---truncated--- | 19 Oct |
| CVE-2026-64115 | 8.8 high | 0.00% | linux, linux_kernel | In the Linux kernel, the following vulnerability has been resolved: vsock/vmci: fix UAF when peer resets connection during handshake vmci_transport_recv_connecting_server() returned err = 0 for a peer RST in its default switch arm: err = pkt->type == VMCI_TRANSPORT_PACKET_TYPE_RST ? 0 : -EINVAL; That made vmci_transport_recv_listen() skip vsock_remove_pending(), leaving the pending socket on the listener's pending_links with sk_state = TCP_CLOSE while destroy: still dropped the explicit reference taken before schedule_delayed_work(). One second later vsock_pending_work() observed is_pending=true and performed full cleanup: vsock_remove_pending() then the two trailing sock_put(sk) calls -- the first reached refcount 0 and __sk_freed the socket, and the second wrote into the freed object: BUG: KASAN: slab-use-after-free in refcount_warn_saturate Write of size 4 at addr ffff88800b1cac80 by task kworker Workqueue: events vsock_pending_work Treat peer RST like any other unexpected packet type (err = -EINVAL). All destroy: arms now return err < 0, so vmci_transport_recv_listen() removes pending from pending_links synchronously and vsock_pending_work() takes the is_pending=false / !rejected branch, dropping only its own work reference. This also closes the multi-packet race Sashiko reported on v2: pending is removed from the list before any subsequent packet can find it. The pre-existing sk_acceptq_removed() gap on the err < 0 path of vmci_transport_recv_listen() that Sashiko also noted is not introduced or changed by this patch. Tested on lts-6.12.79 with KASAN: 52/100 unpatched -> 0/100 patched. | 19 Oct |
| CVE-2025-39982 | 8.8 high | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: Bluetooth: hci_event: Fix UAF in hci_acl_create_conn_sync This fixes the following UFA in hci_acl_create_conn_sync where a connection still pending is command submission (conn->state == BT_OPEN) maybe freed, also since this also can happen with the likes of hci_le_create_conn_sync fix it as well: BUG: KASAN: slab-use-after-free in hci_acl_create_conn_sync+0x5ef/0x790 net/bluetooth/hci_sync.c:6861 Write of size 2 at addr ffff88805ffcc038 by task kworker/u11:2/9541 CPU: 1 UID: 0 PID: 9541 Comm: kworker/u11:2 Not tainted 6.16.0-rc7 #3 PREEMPT(full) Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014 Workqueue: hci3 hci_cmd_sync_work Call Trace: <TASK> dump_stack_lvl+0x189/0x250 lib/dump_stack.c:120 print_address_description mm/kasan/report.c:378 [inline] print_report+0xca/0x230 mm/kasan/report.c:480 kasan_report+0x118/0x150 mm/kasan/report.c:593 hci_acl_create_conn_sync+0x5ef/0x790 net/bluetooth/hci_sync.c:6861 hci_cmd_sync_work+0x210/0x3a0 net/bluetooth/hci_sync.c:332 process_one_work kernel/workqueue.c:3238 [inline] process_scheduled_works+0xae1/0x17b0 kernel/workqueue.c:3321 worker_thread+0x8a0/0xda0 kernel/workqueue.c:3402 kthread+0x70e/0x8a0 kernel/kthread.c:464 ret_from_fork+0x3fc/0x770 arch/x86/kernel/process.c:148 ret_from_fork_asm+0x1a/0x30 home/kwqcheii/source/fuzzing/kernel/kasan/linux-6.16-rc7/arch/x86/entry/entry_64.S:245 </TASK> Allocated by task 123736: kasan_save_stack mm/kasan/common.c:47 [inline] kasan_save_track+0x3e/0x80 mm/kasan/common.c:68 poison_kmalloc_redzone mm/kasan/common.c:377 [inline] __kasan_kmalloc+0x93/0xb0 mm/kasan/common.c:394 kasan_kmalloc include/linux/kasan.h:260 [inline] __kmalloc_cache_noprof+0x230/0x3d0 mm/slub.c:4359 kmalloc_noprof include/linux/slab.h:905 [inline] kzalloc_noprof include/linux/slab.h:1039 [inline] __hci_conn_add+0x233/0x1b30 net/bluetooth/hci_conn.c:939 hci_conn_add_unset net/bluetooth/hci_conn.c:1051 [inline] hci_connect_acl+0x16c/0x4e0 net/bluetooth/hci_conn.c:1634 pair_device+0x418/0xa70 net/bluetooth/mgmt.c:3556 hci_mgmt_cmd+0x9c9/0xef0 net/bluetooth/hci_sock.c:1719 hci_sock_sendmsg+0x6ca/0xef0 net/bluetooth/hci_sock.c:1839 sock_sendmsg_nosec net/socket.c:712 [inline] __sock_sendmsg+0x219/0x270 net/socket.c:727 sock_write_iter+0x258/0x330 net/socket.c:1131 new_sync_write fs/read_write.c:593 [inline] vfs_write+0x54b/0xa90 fs/read_write.c:686 ksys_write+0x145/0x250 fs/read_write.c:738 do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline] do_syscall_64+0xfa/0x3b0 arch/x86/entry/syscall_64.c:94 entry_SYSCALL_64_after_hwframe+0x77/0x7f Freed by task 103680: kasan_save_stack mm/kasan/common.c:47 [inline] kasan_save_track+0x3e/0x80 mm/kasan/common.c:68 kasan_save_free_info+0x46/0x50 mm/kasan/generic.c:576 poison_slab_object mm/kasan/common.c:247 [inline] __kasan_slab_free+0x62/0x70 mm/kasan/common.c:264 kasan_slab_free include/linux/kasan.h:233 [inline] slab_free_hook mm/slub.c:2381 [inline] slab_free mm/slub.c:4643 [inline] kfree+0x18e/0x440 mm/slub.c:4842 device_release+0x9c/0x1c0 kobject_cleanup lib/kobject.c:689 [inline] kobject_release lib/kobject.c:720 [inline] kref_put include/linux/kref.h:65 [inline] kobject_put+0x22b/0x480 lib/kobject.c:737 hci_conn_cleanup net/bluetooth/hci_conn.c:175 [inline] hci_conn_del+0x8ff/0xcb0 net/bluetooth/hci_conn.c:1173 hci_conn_complete_evt+0x3c7/0x1040 net/bluetooth/hci_event.c:3199 hci_event_func net/bluetooth/hci_event.c:7477 [inline] hci_event_packet+0x7e0/0x1200 net/bluetooth/hci_event.c:7531 hci_rx_work+0x46a/0xe80 net/bluetooth/hci_core.c:4070 process_one_work kernel/workqueue.c:3238 [inline] process_scheduled_works+0xae1/0x17b0 kernel/workqueue.c:3321 worker_thread+0x8a0/0xda0 kernel/workqueue.c:3402 kthread+0x70e/0x8a0 kernel/kthread.c:464 ret_from_fork+0x3fc/0x770 arch/x86/kernel/process.c:148 ret_from_fork_asm+0x1a/0x30 home/kwqcheii/sour ---truncated--- | 19 Oct |
| CVE-2025-40000 | 8.8 high | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: wifi: rtw89: fix use-after-free in rtw89_core_tx_kick_off_and_wait() There is a bug observed when rtw89_core_tx_kick_off_and_wait() tries to access already freed skb_data: BUG: KFENCE: use-after-free write in rtw89_core_tx_kick_off_and_wait drivers/net/wireless/realtek/rtw89/core.c:1110 CPU: 6 UID: 0 PID: 41377 Comm: kworker/u64:24 Not tainted 6.17.0-rc1+ #1 PREEMPT(lazy) Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS edk2-20250523-14.fc42 05/23/2025 Workqueue: events_unbound cfg80211_wiphy_work [cfg80211] Use-after-free write at 0x0000000020309d9d (in kfence-#251): rtw89_core_tx_kick_off_and_wait drivers/net/wireless/realtek/rtw89/core.c:1110 rtw89_core_scan_complete drivers/net/wireless/realtek/rtw89/core.c:5338 rtw89_hw_scan_complete_cb drivers/net/wireless/realtek/rtw89/fw.c:7979 rtw89_chanctx_proceed_cb drivers/net/wireless/realtek/rtw89/chan.c:3165 rtw89_chanctx_proceed drivers/net/wireless/realtek/rtw89/chan.h:141 rtw89_hw_scan_complete drivers/net/wireless/realtek/rtw89/fw.c:8012 rtw89_mac_c2h_scanofld_rsp drivers/net/wireless/realtek/rtw89/mac.c:5059 rtw89_fw_c2h_work drivers/net/wireless/realtek/rtw89/fw.c:6758 process_one_work kernel/workqueue.c:3241 worker_thread kernel/workqueue.c:3400 kthread kernel/kthread.c:463 ret_from_fork arch/x86/kernel/process.c:154 ret_from_fork_asm arch/x86/entry/entry_64.S:258 kfence-#251: 0x0000000056e2393d-0x000000009943cb62, size=232, cache=skbuff_head_cache allocated by task 41377 on cpu 6 at 77869.159548s (0.009551s ago): __alloc_skb net/core/skbuff.c:659 __netdev_alloc_skb net/core/skbuff.c:734 ieee80211_nullfunc_get net/mac80211/tx.c:5844 rtw89_core_send_nullfunc drivers/net/wireless/realtek/rtw89/core.c:3431 rtw89_core_scan_complete drivers/net/wireless/realtek/rtw89/core.c:5338 rtw89_hw_scan_complete_cb drivers/net/wireless/realtek/rtw89/fw.c:7979 rtw89_chanctx_proceed_cb drivers/net/wireless/realtek/rtw89/chan.c:3165 rtw89_chanctx_proceed drivers/net/wireless/realtek/rtw89/chan.c:3194 rtw89_hw_scan_complete drivers/net/wireless/realtek/rtw89/fw.c:8012 rtw89_mac_c2h_scanofld_rsp drivers/net/wireless/realtek/rtw89/mac.c:5059 rtw89_fw_c2h_work drivers/net/wireless/realtek/rtw89/fw.c:6758 process_one_work kernel/workqueue.c:3241 worker_thread kernel/workqueue.c:3400 kthread kernel/kthread.c:463 ret_from_fork arch/x86/kernel/process.c:154 ret_from_fork_asm arch/x86/entry/entry_64.S:258 freed by task 1045 on cpu 9 at 77869.168393s (0.001557s ago): ieee80211_tx_status_skb net/mac80211/status.c:1117 rtw89_pci_release_txwd_skb drivers/net/wireless/realtek/rtw89/pci.c:564 rtw89_pci_release_tx_skbs.isra.0 drivers/net/wireless/realtek/rtw89/pci.c:651 rtw89_pci_release_tx drivers/net/wireless/realtek/rtw89/pci.c:676 rtw89_pci_napi_poll drivers/net/wireless/realtek/rtw89/pci.c:4238 __napi_poll net/core/dev.c:7495 net_rx_action net/core/dev.c:7557 net/core/dev.c:7684 handle_softirqs kernel/softirq.c:580 do_softirq.part.0 kernel/softirq.c:480 __local_bh_enable_ip kernel/softirq.c:407 rtw89_pci_interrupt_threadfn drivers/net/wireless/realtek/rtw89/pci.c:927 irq_thread_fn kernel/irq/manage.c:1133 irq_thread kernel/irq/manage.c:1257 kthread kernel/kthread.c:463 ret_from_fork arch/x86/kernel/process.c:154 ret_from_fork_asm arch/x86/entry/entry_64.S:258 It is a consequence of a race between the waiting and the signaling side of the completion: Waiting thread Completing thread rtw89_core_tx_kick_off_and_wait() rcu_assign_pointer(skb_data->wait, wait) /* start waiting */ wait_for_completion_timeout() rtw89_pci_tx_status() rtw89_core_tx_wait_complete() rcu_read_lock() /* signals completion and ---truncated--- | 19 Oct |
| CVE-2025-39983 | 8.8 high | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: Bluetooth: hci_event: Fix UAF in hci_conn_tx_dequeue This fixes the following UAF caused by not properly locking hdev when processing HCI_EV_NUM_COMP_PKTS: BUG: KASAN: slab-use-after-free in hci_conn_tx_dequeue+0x1be/0x220 net/bluetooth/hci_conn.c:3036 Read of size 4 at addr ffff8880740f0940 by task kworker/u11:0/54 CPU: 1 UID: 0 PID: 54 Comm: kworker/u11:0 Not tainted 6.16.0-rc7 #3 PREEMPT(full) Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014 Workqueue: hci1 hci_rx_work Call Trace: <TASK> dump_stack_lvl+0x189/0x250 lib/dump_stack.c:120 print_address_description mm/kasan/report.c:378 [inline] print_report+0xca/0x230 mm/kasan/report.c:480 kasan_report+0x118/0x150 mm/kasan/report.c:593 hci_conn_tx_dequeue+0x1be/0x220 net/bluetooth/hci_conn.c:3036 hci_num_comp_pkts_evt+0x1c8/0xa50 net/bluetooth/hci_event.c:4404 hci_event_func net/bluetooth/hci_event.c:7477 [inline] hci_event_packet+0x7e0/0x1200 net/bluetooth/hci_event.c:7531 hci_rx_work+0x46a/0xe80 net/bluetooth/hci_core.c:4070 process_one_work kernel/workqueue.c:3238 [inline] process_scheduled_works+0xae1/0x17b0 kernel/workqueue.c:3321 worker_thread+0x8a0/0xda0 kernel/workqueue.c:3402 kthread+0x70e/0x8a0 kernel/kthread.c:464 ret_from_fork+0x3fc/0x770 arch/x86/kernel/process.c:148 ret_from_fork_asm+0x1a/0x30 home/kwqcheii/source/fuzzing/kernel/kasan/linux-6.16-rc7/arch/x86/entry/entry_64.S:245 </TASK> Allocated by task 54: kasan_save_stack mm/kasan/common.c:47 [inline] kasan_save_track+0x3e/0x80 mm/kasan/common.c:68 poison_kmalloc_redzone mm/kasan/common.c:377 [inline] __kasan_kmalloc+0x93/0xb0 mm/kasan/common.c:394 kasan_kmalloc include/linux/kasan.h:260 [inline] __kmalloc_cache_noprof+0x230/0x3d0 mm/slub.c:4359 kmalloc_noprof include/linux/slab.h:905 [inline] kzalloc_noprof include/linux/slab.h:1039 [inline] __hci_conn_add+0x233/0x1b30 net/bluetooth/hci_conn.c:939 le_conn_complete_evt+0x3d6/0x1220 net/bluetooth/hci_event.c:5628 hci_le_enh_conn_complete_evt+0x189/0x470 net/bluetooth/hci_event.c:5794 hci_event_func net/bluetooth/hci_event.c:7474 [inline] hci_event_packet+0x78c/0x1200 net/bluetooth/hci_event.c:7531 hci_rx_work+0x46a/0xe80 net/bluetooth/hci_core.c:4070 process_one_work kernel/workqueue.c:3238 [inline] process_scheduled_works+0xae1/0x17b0 kernel/workqueue.c:3321 worker_thread+0x8a0/0xda0 kernel/workqueue.c:3402 kthread+0x70e/0x8a0 kernel/kthread.c:464 ret_from_fork+0x3fc/0x770 arch/x86/kernel/process.c:148 ret_from_fork_asm+0x1a/0x30 home/kwqcheii/source/fuzzing/kernel/kasan/linux-6.16-rc7/arch/x86/entry/entry_64.S:245 Freed by task 9572: kasan_save_stack mm/kasan/common.c:47 [inline] kasan_save_track+0x3e/0x80 mm/kasan/common.c:68 kasan_save_free_info+0x46/0x50 mm/kasan/generic.c:576 poison_slab_object mm/kasan/common.c:247 [inline] __kasan_slab_free+0x62/0x70 mm/kasan/common.c:264 kasan_slab_free include/linux/kasan.h:233 [inline] slab_free_hook mm/slub.c:2381 [inline] slab_free mm/slub.c:4643 [inline] kfree+0x18e/0x440 mm/slub.c:4842 device_release+0x9c/0x1c0 kobject_cleanup lib/kobject.c:689 [inline] kobject_release lib/kobject.c:720 [inline] kref_put include/linux/kref.h:65 [inline] kobject_put+0x22b/0x480 lib/kobject.c:737 hci_conn_cleanup net/bluetooth/hci_conn.c:175 [inline] hci_conn_del+0x8ff/0xcb0 net/bluetooth/hci_conn.c:1173 hci_abort_conn_sync+0x5d1/0xdf0 net/bluetooth/hci_sync.c:5689 hci_cmd_sync_work+0x210/0x3a0 net/bluetooth/hci_sync.c:332 process_one_work kernel/workqueue.c:3238 [inline] process_scheduled_works+0xae1/0x17b0 kernel/workqueue.c:3321 worker_thread+0x8a0/0xda0 kernel/workqueue.c:3402 kthread+0x70e/0x8a0 kernel/kthread.c:464 ret_from_fork+0x3fc/0x770 arch/x86/kernel/process.c:148 ret_from_fork_asm+0x1a/0x30 home/kwqcheii/source/fuzzing/kernel/kasan/linux-6.16-rc7/arch/x86/entry/entry_64.S:245 | 19 Oct |
| CVE-2026-68432 | 8.8 high | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: vxlan: require CAP_NET_ADMIN in the device netns for changelink A tunnel changelink() operates on at most two netns, dev_net(dev) and the sticky underlay netns vxlan->net. They differ once the device is created in or moved to a netns other than the one the request runs in. The rtnl changelink path checks CAP_NET_ADMIN only against dev_net(dev), so a caller privileged there but not in vxlan->net can rewrite a vxlan device whose underlay lives in vxlan->net. vxlan_changelink() validates and applies the new configuration against vxlan->net (vxlan_config_validate(vxlan->net, ...)) and can reopen the underlay socket in that netns, so the same reasoning as the tunnel changelink series applies here. Gate vxlan_changelink() with rtnl_dev_link_net_capable(), at the top of the op before any attribute is parsed, matching ipgre_changelink() and the rest of the "require CAP_NET_ADMIN in the device netns for changelink" series. Found by 0sec automated security-research tooling (https://0sec.ai). | 19 Oct |
| CVE-2026-68142 | 8.8 high | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: geneve: require CAP_NET_ADMIN in the device netns for changelink A tunnel changelink() operates on at most two netns, dev_net(dev) and the sticky underlay netns geneve->net. They differ once the device is created in or moved to a netns other than the one the request runs in. The rtnl changelink path checks CAP_NET_ADMIN only against dev_net(dev), so a caller privileged there but not in geneve->net can rewrite a geneve device whose underlay lives in geneve->net. geneve_changelink() applies the new configuration against geneve->net: geneve_link_config() and the geneve_quiesce()/geneve_unquiesce() pair reopen the underlay sockets in that netns (geneve_sock_add() uses geneve->net), so the same reasoning as the tunnel changelink series applies here. Gate geneve_changelink() with rtnl_dev_link_net_capable(), at the top of the op before any attribute is parsed, matching ipgre_changelink() and the rest of the "require CAP_NET_ADMIN in the device netns for changelink" series. Found by 0sec automated security-research tooling (https://0sec.ai). | 19 Oct |
| CVE-2026-68128 | 8.8 high | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: ice: reject out-of-range ptype in ice_parser_profile_init set_bit(rslt->ptype, prof->ptypes) operates on a DECLARE_BITMAP of ICE_FLOW_PTYPE_MAX (1024) bits. Nothing prevents a malicious VF from providing ptype >= 1024 through VIRTCHNL, resulting in a write past the end of the bitmap and a kernel page fault. Reproduced with a custom kernel module injecting a crafted VIRTCHNL_OP_ADD_RSS_CFG on E810-C QSFP (8086:1592), FW 4.91 0x800214af 1.3909.0, ICE COMMS DDP 1.3.53.0, kernel 7.1.0-rc1. crash_parser: ice_parser_profile_init @ ffffffffc0d61b60 crash_parser: setting ptype=0xffff (max valid=1023) crash_parser: calling ice_parser_profile_init -- expect OOB crash! BUG: kernel NULL pointer dereference, address: 0000000000000000 Oops: Oops: 0002 [#1] SMP NOPTI CPU: 56 UID: 0 PID: 165011 Comm: insmod Kdump: loaded Tainted: G S U OE 7.1.0-rc1 #1 Hardware name: Intel Corporation S2600BPB/S2600BPB RIP: 0010:ice_parser_profile_init+0x2d/0x1d0 [ice] Call Trace: <TASK> ? __pfx_ice_parser_profile_init+0x10/0x10 [ice] crash_init+0x127/0xff0 [crash_parser] do_one_initcall+0x45/0x310 do_init_module+0x64/0x270 init_module_from_file+0xcc/0xf0 idempotent_init_module+0x17b/0x280 __x64_sys_finit_module+0x6e/0xe0 Bail out early with -EINVAL when ptype is out of range. | 19 Oct |
| CVE-2026-64557 | 8.8 high | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: Bluetooth: L2CAP: Fix use-after-free in l2cap_sock_new_connection_cb() l2cap_sock_new_connection_cb() returned l2cap_pi(sk)->chan after release_sock(parent). Once the parent lock is dropped the newly enqueued child socket sk is reachable via the accept queue, so another task can accept and free it before the callback dereferences sk, resulting in a use-after-free. Rework the ->new_connection() op so the core, rather than the callback, owns the child channel's lifetime. The op now receives a pre-allocated new_chan and returns an errno instead of allocating and returning a channel. l2cap_new_connection() allocates the child channel and links it into the conn list via __l2cap_chan_add() before invoking the callback, so the conn-list reference keeps the channel alive once release_sock(parent) exposes the socket to other tasks. Channel configuration that was duplicated in l2cap_sock_init() and the various new_connection callbacks is consolidated into l2cap_chan_set_defaults(), which now inherits from the parent channel when one is supplied. | 19 Oct |
| CVE-2026-53375 | 8.8 high | 0.00% | linux, linux_kernel | In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu/vce: Prevent partial address patches In the case that only one of lo/hi is valid, the patching could result in a bad address written to in FW. | 19 Oct |
| CVE-2026-53275 | 8.8 high | 0.00% | linux, linux_kernel | In the Linux kernel, the following vulnerability has been resolved: ipv6: mcast: Fix use-after-free when processing MLD queries When processing an MLD query, a pointer to the multicast group address is retrieved when initially parsing the packet. This pointer is later dereferenced without being reloaded despite the fact that the skb header might have been reallocated following the pskb_may_pull() calls, leading to a use-after-free [1]. Fix by copying the multicast group address when the packet is initially parsed. [1] BUG: KASAN: slab-use-after-free in __mld_query_work (net/ipv6/mcast.c:1512) Read of size 8 at addr ffff8881154b8e90 by task kworker/4:1/118 Workqueue: mld mld_query_work Call Trace: <TASK> dump_stack_lvl (lib/dump_stack.c:94 lib/dump_stack.c:120) print_address_description.constprop.0 (mm/kasan/report.c:378) print_report (mm/kasan/report.c:482) kasan_report (mm/kasan/report.c:595) __mld_query_work (net/ipv6/mcast.c:1512) mld_query_work (net/ipv6/mcast.c:1563) process_one_work (kernel/workqueue.c:3314) worker_thread (kernel/workqueue.c:3397 kernel/workqueue.c:3478) kthread (kernel/kthread.c:436) ret_from_fork (arch/x86/kernel/process.c:158) ret_from_fork_asm (arch/x86/entry/entry_64.S:245) </TASK> [...] Freed by task 118: kasan_save_stack (mm/kasan/common.c:57) kasan_save_track (mm/kasan/common.c:78) kasan_save_free_info (mm/kasan/generic.c:584) __kasan_slab_free (mm/kasan/common.c:253 mm/kasan/common.c:285) kfree (./include/linux/kasan.h:235 mm/slub.c:2689 mm/slub.c:6251 mm/slub.c:6566) pskb_expand_head (net/core/skbuff.c:2335) __pskb_pull_tail (net/core/skbuff.c:2878 (discriminator 4)) __mld_query_work (net/ipv6/mcast.c:1495 (discriminator 1)) mld_query_work (net/ipv6/mcast.c:1563) process_one_work (kernel/workqueue.c:3314) worker_thread (kernel/workqueue.c:3397 kernel/workqueue.c:3478) kthread (kernel/kthread.c:436) ret_from_fork (arch/x86/kernel/process.c:158) ret_from_fork_asm (arch/x86/entry/entry_64.S:245) | 19 Oct |
| CVE-2026-46152 | 8.8 high | 0.00% | linux, linux_kernel | In the Linux kernel, the following vulnerability has been resolved: wifi: mac80211: drop stray 'static' from fast-RX rx_result ieee80211_invoke_fast_rx() is documented as safe for parallel RX, but its per-invocation rx_result is declared static. Concurrent callers then share one instance and can overwrite each other's result between ieee80211_rx_mesh_data() and the switch on res. That can make a packet that was queued or consumed by ieee80211_rx_mesh_data() fall through into ieee80211_rx_8023(), or make a packet that should continue return as queued. Make res an automatic variable so each invocation keeps its own result. | 19 Oct |
| CVE-2026-43158 | 8.8 high | 0.00% | linux, linux_kernel | In the Linux kernel, the following vulnerability has been resolved: xfs: fix freemap adjustments when adding xattrs to leaf blocks xfs/592 and xfs/794 both trip this assertion in the leaf block freemap adjustment code after ~20 minutes of running on my test VMs: ASSERT(ichdr->firstused >= ichdr->count * sizeof(xfs_attr_leaf_entry_t) + xfs_attr3_leaf_hdr_size(leaf)); Upon enabling quite a lot more debugging code, I narrowed this down to fsstress trying to set a local extended attribute with namelen=3 and valuelen=71. This results in an entry size of 80 bytes. At the start of xfs_attr3_leaf_add_work, the freemap looks like this: i 0 base 448 size 0 rhs 448 count 46 i 1 base 388 size 132 rhs 448 count 46 i 2 base 2120 size 4 rhs 448 count 46 firstused = 520 where "rhs" is the first byte past the end of the leaf entry array. This is inconsistent -- the entries array ends at byte 448, but freemap[1] says there's free space starting at byte 388! By the end of the function, the freemap is in worse shape: i 0 base 456 size 0 rhs 456 count 47 i 1 base 388 size 52 rhs 456 count 47 i 2 base 2120 size 4 rhs 456 count 47 firstused = 440 Important note: 388 is not aligned with the entries array element size of 8 bytes. Based on the incorrect freemap, the name area starts at byte 440, which is below the end of the entries array! That's why the assertion triggers and the filesystem shuts down. How did we end up here? First, recall from the previous patch that the freemap array in an xattr leaf block is not intended to be a comprehensive map of all free space in the leaf block. In other words, it's perfectly legal to have a leaf block with: * 376 bytes in use by the entries array * freemap[0] has [base = 376, size = 8] * freemap[1] has [base = 388, size = 1500] * the space between 376 and 388 is free, but the freemap stopped tracking that some time ago If we add one xattr, the entries array grows to 384 bytes, and freemap[0] becomes [base = 384, size = 0]. So far, so good. But if we add a second xattr, the entries array grows to 392 bytes, and freemap[0] gets pushed up to [base = 392, size = 0]. This is bad, because freemap[1] hasn't been updated, and now the entries array and the free space claim the same space. The fix here is to adjust all freemap entries so that none of them collide with the entries array. Note that this fix relies on commit 2a2b5932db6758 ("xfs: fix attr leaf header freemap.size underflow") and the previous patch that resets zero length freemap entries to have base = 0. | 19 Oct |
| CVE-2026-31709 | 8.8 high | 0.00% | linux, linux_kernel | In the Linux kernel, the following vulnerability has been resolved: smb: client: validate the whole DACL before rewriting it in cifsacl build_sec_desc() and id_mode_to_cifs_acl() derive a DACL pointer from a server-supplied dacloffset and then use the incoming ACL to rebuild the chmod/chown security descriptor. The original fix only checked that the struct smb_acl header fits before reading dacl_ptr->size or dacl_ptr->num_aces. That avoids the immediate header-field OOB read, but the rewrite helpers still walk ACEs based on pdacl->num_aces with no structural validation of the incoming DACL body. A malicious server can return a truncated DACL that still contains a header, claims one or more ACEs, and then drive replace_sids_and_copy_aces() or set_chmod_dacl() past the validated extent while they compare or copy attacker-controlled ACEs. Factor the DACL structural checks into validate_dacl(), extend them to validate each ACE against the DACL bounds, and use the shared validator before the chmod/chown rebuild paths. parse_dacl() reuses the same validator so the read-side parser and write-side rewrite paths agree on what constitutes a well-formed incoming DACL. | 19 Oct |
| CVE-2026-63917 | 8.8 high | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: ip6: vti: Use ip6_tnl.net in vti6_changelink(). ip netns add ns1 ip netns add ns2 ip -n ns1 link add vti6_test type vti6 remote ::1 local ::2 key 7 ip -n ns1 link set vti6_test netns ns2 ip -n ns2 link set vti6_test type vti6 remote ::3 local ::4 key 9 ip netns del ns2 ip netns del ns1 [ 132.495484] ------------[ cut here ]------------ [ 132.497609] kernel BUG at net/core/dev.c:12376! Commit 61220ab34948 ("vti6: Enable namespace changing") dropped NETIF_F_NETNS_LOCAL from vti6 devices. A vti6 tunnel can then move through IFLA_NET_NS_FD. After the move dev_net(dev) points at the new netns while t->net stays at the creation netns. vti6_changelink() and vti6_update() still use dev_net(dev) and dev_net(t->dev). They unlink from one per netns hash and relink into another. The creation netns is left with a stale entry. cleanup_net() of that netns later walks freed memory. Reachable from an unprivileged user namespace (unshare --user --map-root-user --net). Cross tenant scope on container hosts. | 19 Oct |
| CVE-2026-63916 | 8.8 high | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: HID: wacom: Fix OOB write in wacom_hid_set_device_mode() wacom_hid_set_device_mode() currently assumes that the HID_DG_INPUTMODE usage is always located in the first field (field[0]) of the feature report. However, a device can specify HID_DG_INPUTMODE in a different field. If HID_DG_INPUTMODE is in a field other than the first one and the first field has a report_count smaller than the usage_index of HID_DG_INPUTMODE, this leads to an out-of-bounds write to r->field[0]->value. Fix this by storing the field index of HID_DG_INPUTMODE in 'struct hid_data' during feature mapping. In wacom_hid_set_device_mode(), use this stored field index to access the correct field and add bounds checks to ensure both the field index and the value index are within valid ranges before writing. | 19 Oct |
| CVE-2026-31588 | 8.8 high | 0.00% | linux, linux_kernel | In the Linux kernel, the following vulnerability has been resolved: KVM: x86: Use scratch field in MMIO fragment to hold small write values When exiting to userspace to service an emulated MMIO write, copy the to-be-written value to a scratch field in the MMIO fragment if the size of the data payload is 8 bytes or less, i.e. can fit in a single chunk, instead of pointing the fragment directly at the source value. This fixes a class of use-after-free bugs that occur when the emulator initiates a write using an on-stack, local variable as the source, the write splits a page boundary, *and* both pages are MMIO pages. Because KVM's ABI only allows for physically contiguous MMIO requests, accesses that split MMIO pages are separated into two fragments, and are sent to userspace one at a time. When KVM attempts to complete userspace MMIO in response to KVM_RUN after the first fragment, KVM will detect the second fragment and generate a second userspace exit, and reference the on-stack variable. The issue is most visible if the second KVM_RUN is performed by a separate task, in which case the stack of the initiating task can show up as truly freed data. ================================================================== BUG: KASAN: use-after-free in complete_emulated_mmio+0x305/0x420 Read of size 1 at addr ffff888009c378d1 by task syz-executor417/984 CPU: 1 PID: 984 Comm: syz-executor417 Not tainted 5.10.0-182.0.0.95.h2627.eulerosv2r13.x86_64 #3 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.15.0-0-g2dd4b9b3f840-prebuilt.qemu.org 04/01/2014 Call Trace: dump_stack+0xbe/0xfd print_address_description.constprop.0+0x19/0x170 __kasan_report.cold+0x6c/0x84 kasan_report+0x3a/0x50 check_memory_region+0xfd/0x1f0 memcpy+0x20/0x60 complete_emulated_mmio+0x305/0x420 kvm_arch_vcpu_ioctl_run+0x63f/0x6d0 kvm_vcpu_ioctl+0x413/0xb20 __se_sys_ioctl+0x111/0x160 do_syscall_64+0x30/0x40 entry_SYSCALL_64_after_hwframe+0x67/0xd1 RIP: 0033:0x42477d Code: <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b0 ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007faa8e6890e8 EFLAGS: 00000246 ORIG_RAX: 0000000000000010 RAX: ffffffffffffffda RBX: 00000000004d7338 RCX: 000000000042477d RDX: 0000000000000000 RSI: 000000000000ae80 RDI: 0000000000000005 RBP: 00000000004d7330 R08: 00007fff28d546df R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 00000000004d733c R13: 0000000000000000 R14: 000000000040a200 R15: 00007fff28d54720 The buggy address belongs to the page: page:0000000029f6a428 refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x9c37 flags: 0xfffffc0000000(node=0|zone=1|lastcpupid=0x1fffff) raw: 000fffffc0000000 0000000000000000 ffffea0000270dc8 0000000000000000 raw: 0000000000000000 0000000000000000 00000000ffffffff 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff888009c37780: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ffff888009c37800: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff >ffff888009c37880: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ^ ffff888009c37900: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ffff888009c37980: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ================================================================== The bug can also be reproduced with a targeted KVM-Unit-Test by hacking KVM to fill a large on-stack variable in complete_emulated_mmio(), i.e. by overwrite the data value with garbage. Limit the use of the scratch fields to 8-byte or smaller accesses, and to just writes, as larger accesses and reads are not affected thanks to implementation details in the emulator, but add a sanity check to ensure those details don't change in the future. Specifically, KVM never uses on-stack variables for accesses larger that 8 bytes, e.g. uses an operand in the emulator context, and *al ---truncated--- | 19 Oct |
| CVE-2026-98339 | 8.8 high | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: wifi: cfg80211: don't filter by BSS type when removing stale entries When an assoc AP switches to a channel that already has a BSS entry, cfg80211_update_assoc_bss_entry() removes that entry before rehashing the real one, since the two would otherwise collide in the BSS rbtree. The lookup for that entry also required it to match the connection's BSS type, so an entry advertising e.g. the IBSS capability bit was left in place, and the following cfg80211_rehash_bss() then ran into it: WARN_ON(!cmp) Changing the type shouldn't really happen, but can be triggered by a rogue AP/device, so drop the check and remove any entries matching the comparison. | 19 Oct |
| CVE-2026-98115 | 8.8 high | 0.00% | linux, linux_kernel | In the Linux kernel, the following vulnerability has been resolved: ksmbd: safely drain sessions during logoff SMB3 multichannel allows requests for one session to run on multiple connections. Wait for all channels bound to a session before freeing shared session objects. A deferred byte-range lock remains counted as a running request and only wakes when its file closes. Wake blocked locks during the drain without unpublishing or modifying their file objects. Synchronous CANCEL requests must invoke their cancellation callback to wake pending operations, while CHANGE_NOTIFY completion remains specific to the asynchronous path. Serialize session teardown with channel registration and previous-session cleanup, and use atomic work-state transitions so LOGOFF, CANCEL, and connection teardown invoke cancellation callbacks only once. | 19 Oct |
| CVE-2026-93189 | 8.8 high | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: HID: core: quiesce input in hid_hw_stop() to prevent use-after-free A driver's probe calls hid_device_io_start() to enable input delivery, then fails at a later initialization step and unwinds via hid_hw_stop(). The unwind frees struct hidraw via hidraw_disconnect() while in-flight HID reports may still be running on another CPU, dereferencing the freed object through hidraw_report_event(). syzbot reports the resulting use-after-free for the corsair-psu HID driver. Edward Adam Davis posted a per-driver fix for corsair-psu that adds an explicit hid_device_io_stop() before hid_hw_stop() in the probe error path ("hwmon: prevent packets from going to driver for probe", 2026-04-28). Auditing the tree shows 15 drivers call hid_device_io_start(); 7 also call hid_device_io_stop() and 8 do not: drivers calling hid_device_io_start() without a matching hid_device_io_stop() before hid_hw_stop(): drivers/hwmon/corsair-psu.c (fix posted by Edward) drivers/hwmon/corsair-cpro.c drivers/hwmon/nzxt-kraken3.c drivers/hwmon/nzxt-smart2.c drivers/hwmon/gigabyte_waterforce.c drivers/hid/hid-logitech-dj.c drivers/hid/hid-nintendo.c drivers/hid/hid-mcp2221.c Roughly half of all callers of the API are exposed. Centralize the quiesce in hid_hw_stop() so callers do not have to remember the matching stop: if a driver has left hdev->io_started true on entry, call hid_device_io_stop() before hid_disconnect(). For the 7 drivers that already call hid_device_io_stop() correctly, hdev->io_started is false on entry, the guard short-circuits, and behavior is unchanged. No Fixes: tag because the affected drivers gained their hid_device_io_start() calls independently over years; the bug is a class-wide API misuse rather than a regression from one commit. | 19 Oct |
| CVE-2026-90425 | 8.8 high | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: iommu/tegra241-cmdqv: Require exactly one Stream ID for a vSID tegra241_vintf_init_vsid() maps a guest vSID to a single physical Stream ID taken from master->streams[0], and only warns when the device does not have exactly one stream. A device with several streams gets only its first one mapped, so a guest vSID invalidation cannot reach the others' ATC and IOTLB entries; a device with none makes master->streams a ZERO_SIZE_PTR, read out of bounds. Reject the mapping with -EOPNOTSUPP if master->num_streams is not one. | 19 Oct |
| CVE-2026-90379 | 8.8 high | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: wifi: mt76: mt7921: Add PCIe AER handler support to prevent system crash When an AER error occurs and the bus is hung, the register reads return 0xFFFFFFFF, causing the DMA queue state to be corrupted and resulting in an invalid memory access when accessing q->desc[] or q->entry[]. Unable to handle kernel paging request at virtual address ffffffc01099eac0 pc : mt76_dma_add_buf+0x124/0x188 [mt76] lr : mt76_dma_rx_fill+0x11c/0x1d8 [mt76] sp : ffffffc016d9bbf0 x29: ffffffc016d9bc10 x28: 0000000000000000 x27: 0000000000000000 x26: ffffffb7855e50b8 x25: ffffffb80d04f000 x24: 0000000000000000 x23: 0000000000000ec0 x22: ffffffb796803648 x21: ffffffb796801f80 x20: ffffffb7968035f8 x19: 0000000000000ec0 x18: 0000000000000000 x17: 000000004ec00000 x16: 000000000ec00000 x15: ffffffc01099eac0 x14: 000000004ec00000 x13: 00000000ffc5a000 x12: ffffffc016d9bc32 x11: 00000000ffffffff x10: 0000000000000002 x9 : 0000000000000000 x8 : 000000000000b4ac x7 : 0000000000000a20 x6 : ffffffb6c1806400 x5 : 0000000000000000 x4 : ffffffb80d04f000 x3 : 0000000000000000 x2 : 0000000000000001 x1 : 000000000ec04000 x0 : ffffffb7968035f8 Call trace: mt76_dma_add_buf+0x124/0x188 [mt76 (HASH:1029 4)] mt76_dma_rx_reset+0xe8/0xfc [mt76 (HASH:1029 4)] mt7921_wpdma_reset+0x188/0x1b0 [mt7921e (HASH:ee48 5)] mt7921e_mac_reset+0x128/0x418 [mt7921e (HASH:ee48 5)] mt7921_mac_reset_work+0xac/0x1a8 [mt7921_common (HASH:f721 6)] process_one_work+0x188/0x514 worker_thread+0x12c/0x300 kthread+0x140/0x1fc ret_from_fork+0x10/0x30 Fix the invalid memory access by validating the DMA index read from the hardware before it is used as a queue index. An out-of-range value, such as the 0xFFFFFFFF returned while the bus is hung, is now clamped so it can no longer corrupt q->head or q->tail. In addition, check the bus_hung flag in mt7921_mac_reset_work() before attempting the reset sequence, reject MCU messages while the bus is hung, and install no-op bus operations when an unrecoverable AER error is detected, preventing further invalid hardware accesses. Due to hardware limitations - such as the lack of a connected hardware reset pin or the absence of host re-probe functionality - affected Wi-Fi devices may not fully recover to a normal operational state after certain errors, even with AER enabled. | 19 Oct |
| CVE-2026-90000 | 8.8 high | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: HID: rmi: fix OOB access with undersized RMI reports The hid-rmi driver sizes its writeReport/readReport buffer purely from the report descriptor supplied by the device, with no minimum bound: data->input_report_size = hid_report_len(input_report); data->output_report_size = hid_report_len(output_report); alloc_size = data->output_report_size + data->input_report_size; data->writeReport = devm_kzalloc(&hdev->dev, alloc_size, GFP_KERNEL); data->readReport = data->writeReport + data->output_report_size; but then reads and writes fixed offsets into it. A device declaring a 1-byte output and a 1-byte input report makes hid_report_len() return 2 for each, so alloc_size is 4, while rmi_set_page() -- reached unconditionally at probe time through rmi_input_configured() -- stores writeReport[4] and rmi_hid_read_block() stores writeReport[0..5]. Since readReport lives at writeReport + output_report_size, those stores also corrupt the window the next reply is parsed out of. The read path is worse: the copy length comes from readReport[1], which the device fills in and can be up to 255, and the copy starts at &readReport[2] with no regard for input_report_size, so it runs past the end of the allocation into adjacent slab objects. This does not even need a lying device -- rmi_f01_probe() issues a fixed 21-byte register read, so any device declaring an input report smaller than 23 bytes reads out of bounds even when it answers truthfully. Those bytes become the register values the RMI core acts on: rmi_f01_probe() prints them to the kernel log as the product id and exports them through the mode 0444 sysfs attribute of the same name, and rmi_driver_set_irq_bits() sends them back to the device as the interrupt mask, so an undersized report descriptor leaks heap contents both to unprivileged userspace and to the device itself. The write path has no bound either: rmi_hid_write_block() copies an unbounded len to &writeReport[4], and the largest caller a device can drive at probe time is rmi_driver_set_irq_bits(), whose length is derived from the interrupt source counts the device declares in its Page Description Table. Finally, the read loop cannot terminate on a zero-length reply: such a reply copies nothing and advances neither bytes_read nor bytes_needed, and because a reply did arrive the one second wait_event_timeout() does not fire either, so a device answering 0 forever keeps the loop running inside the probe worker with page_mutex held. khungtaskd does not notice, because every reply wakes the task. Reject reports too small for what the driver builds -- 6 output bytes for the write reports and 3 input bytes for the read handshake -- at probe time, clamp the write and the read copy to the report sizes the device declared, and treat a zero-length reply as an error. A device refused this way is started as an ordinary HID device, like one that does not carry the RMI report ids at all. RMI_DEVICE must not be left set in device_flags on that path, because rmi_input_configured() would then run the RMI setup and reach rmi_set_page(), which writes the writeReport buffer the refusal just skipped allocating. The bit can arrive set: rmi_probe() copies id->driver_data into device_flags before the report checks, and a bind through the new_id sysfs attribute can supply driver_data with RMI_DEVICE (BIT(0)) set. Strip the bit where driver_data is copied, so RMI_DEVICE keeps meaning exactly "this probe validated the reports"; the three jumps to start that predate this patch are covered as well. The error path also clears RMI_READ_DATA_PENDING on its way out, because that flag is what the wait at the top of the loop tests: leaving it set would make every later wait_event_timeout() return immediately on the stale reply and kill the read path for the rest of the device's life. Clamping does not regress working hardware: the read loop already handles ---truncated--- | 19 Oct |
| CVE-2026-89804 | 8.8 high | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: drm/nouveau/dmem: fix mismatched DMA unmap size for large folios Device-private THP migration maps migration buffers with page_size() and records that length in dma_info->size. For a compound folio page_size() is PAGE_SIZE << order, but two teardown sites still pass a literal PAGE_SIZE to dma_unmap_page(): - nouveau_dmem_migrate_to_ram() on the success path, and - nouveau_dmem_migrate_copy_one() on the copy-error path. For an order > 0 folio this unmaps less than was mapped, leaking the remainder of the IOMMU/IOVA mapping. The other unmap sites, in nouveau_dmem_migrate_chunk() and nouveau_dmem_evict_chunk(), already use the saved size; use it here too. | 19 Oct |
| CVE-2026-89729 | 8.8 high | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: HID: sensor-hub: Fix out-of-bounds write in sensor_hub_get_feature sensor_hub_get_feature() clamps its return value to the caller's buffer size, but the copy loop still copies field->report_size / 8 bytes for each report value. A malicious HID descriptor can advertise a large feature field size while an IIO caller supplies a small stack buffer, such as a single s32, causing an out-of-bounds write. HID core stores parsed report values in __s32 slots and clamps extracted values to 32 bits. Reject feature fields that require more than one slot per value, guard the total byte count calculation, and clamp each per-value copy to the remaining caller buffer. | 19 Oct |
| CVE-2026-89663 | 8.8 high | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: nfsd: revoke copy-notify stateids before dropping their reference Copy-notify stateids live in the s2s_cp_stateids IDR and on their parent stid's sc_cp_list, pinned by a single membership reference. _free_cpntf_state_locked() only unlinks an entry once its refcount reaches zero, so any revoke path that runs while a concurrent find_cpntf_state()/manage_cpntf_state() holder has elevated cs_count drops the reference without unlinking, leaving the entry discoverable with its membership reference already consumed. A second revoke or a laundromat tick then frees it while the reader still holds the pointer -- a KASAN-detectable use-after-free at the reader's nfs4_put_cpntf_state(). This affected all three revoke paths: - The parent-stid drain (nfs4_free_cpntf_statelist()) repeatedly called _free_cpntf_state_locked() on the first list entry; a holder that had bumped cs_count made it return early, so the next iteration re-decremented and burned the holder's reference. - OFFLOAD_CANCEL (manage_cpntf_state()) and laundromat expiry likewise used _free_cpntf_state_locked() and could drop 2->1 without unlinking. Add revoke_cpntf_state_locked(), which unhashes the entry from the IDR and sc_cp_list first (deferring the final free to any holder), and use it from all three revoke paths. The drain now walks with list_for_each_entry_safe() and revokes each entry unconditionally, so it terminates in one pass per entry regardless of cs_count. The unhash is gated on !list_empty(&cps->cp_list); the idr_remove() gate matters because idr_alloc_cyclic() may have recycled the so_id by then. Keep _free_cpntf_state_locked() for the reference-holder put path only, where a concurrent revoke may already have unlinked the entry (its list_del_init() then a no-op). | 19 Oct |
| CVE-2026-89626 | 8.8 high | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: HID: sensor: custom: Fix field sysfs group cleanup on failure hid_sensor_custom_add_attributes() creates one sysfs group for each custom sensor field. If sysfs_create_group() fails after some groups have already been created, the function returns the error without removing the previously created groups. Add a local unwind path to remove the groups that were already created. With enable_sensor exposed only after the field attributes are ready, this path can free sensor_inst->fields without leaving enable_sensor able to access pointers into that array. | 19 Oct |
| CVE-2026-89513 | 8.8 high | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: RISC-V: KVM: Fix PMU event info array size overflow SBI PMU EVENT_GET_INFO stores guest-controlled num_events * sizeof(*einfo) in a 32-bit integer. On RV64, num_events = 0x10000001 makes 0x100000010 truncate to 16. KVM then allocates one entry but loops over the original num_events, causing out-of-bounds reads and writes. A nested guest triggered: BUG: KASAN: slab-out-of-bounds in kvm_riscv_vcpu_pmu_event_info+0xa4/0x142 Read of size 4 at addr ff600000074d46b0 by task init/1 Call Trace: [<ffffffff8006471c>] kvm_riscv_vcpu_pmu_event_info+0xa4/0x142 [<ffffffff800690c0>] kvm_sbi_ext_pmu_handler+0xca/0x268 [<ffffffff8006779e>] kvm_riscv_vcpu_sbi_ecall+0xec/0x1e6 [<ffffffff8006008c>] kvm_riscv_vcpu_exit+0x48c/0x540 [<ffffffff8005ea0a>] kvm_arch_vcpu_ioctl_run+0x37e/0xc80 Allocated by task 1: __kmalloc_noprof+0x19e/0x4b0 kvm_riscv_vcpu_pmu_event_info+0x72/0x142 kvm_sbi_ext_pmu_handler+0xca/0x268 kvm_riscv_vcpu_sbi_ecall+0xec/0x1e6 kvm_riscv_vcpu_exit+0x48c/0x540 kvm_arch_vcpu_ioctl_run+0x37e/0xc80 The buggy address is located 0 bytes to the right of allocated 16-byte region [ff600000074d46a0, ff600000074d46b0) Store the shared-memory size in size_t and reject multiplication overflow. Allocate the guest-driven array with GFP_KERNEL_ACCOUNT so it is charged to kmemcg, and use __GFP_NOWARN to suppress allocation failure warnings. Use kvcalloc() to allow vmalloc fallback and an unsigned long loop index to match num_events. | 19 Oct |
| CVE-2026-80989 | 8.8 high | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: net: thunderbolt: Mark the connection down when bringing it up fails Every failure path in tbnet_connected_work() undoes its own work and returns without clearing login_sent, so the connection still looks established. The next tbnet_tear_down() therefore takes its main branch and repeats a teardown that already happened: it stops rings that are already stopped, which is a dev_WARN() and fatal under panic_on_warn, and it releases net->remote_transmit_path even on the HopID mismatch path, where this connection never owned that id, silently freeing one that someone else is still using. Clear login_sent on those paths. That is enough for tbnet_tear_down() to leave the unwound state alone, and login_received has to stay set: it records that the peer has logged in and carries the transmit path it gave us, which nothing on this side can make the peer send again. Two things change beyond keeping the teardown out of the way: the logout request in that block is no longer sent, and the peer's next login request now re-queues our login work rather than connected_work, giving the connection a fresh login instead of a retry on stale state. | 19 Oct |
| CVE-2026-80914 | 8.8 high | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: Bluetooth: ISO: fix use-after-free of listener socket in iso_conn_ready iso_conn_ready() looks up the BIS listener socket with iso_get_sock(), which takes a reference, and then, without re-checking its state, creates a child socket from it: parent = iso_get_sock(hdev, ...); if (!parent) return; lock_sock(parent); sk = iso_sock_alloc(sock_net(parent), NULL, BTPROTO_ISO, ...); ... iso_chan_add(conn, sk, parent); ... release_sock(parent); sock_put(parent); If the listener socket is closed concurrently, between iso_get_sock() and lock_sock(), the reference taken by iso_get_sock() may be the last one: the close path drops the link-list reference, and once iso_conn_ready() drops its own reference at the end of the function the socket is freed. The child socket, however, is already linked to the freed parent, and a later disconnect of the child runs iso_chan_del() -> bt_accept_unlink(), which dereferences the dangling parent pointer into the freed accept queue (a use-after-free). The same dangling pointer is also dereferenced through parent->***() in iso_chan_del(). Fix it the same way the connected (non-BIS) path was fixed in commit 0d255e63fcf3 ("Bluetooth: ISO: hold sk properly in iso_conn_ready"): after taking the socket lock, re-check that the parent is still a listening, alive socket, and bail out otherwise. | 19 Oct |
| CVE-2026-80683 | 8.8 high | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: Bluetooth: SCO: give the socket its own sco_conn reference sco_conn_del() drops a reference it does not own. It takes one transient reference via sco_conn_hold_unless_zero() and releases it with the sco_conn_put() that follows sco_sock_hold(); the additional put in the !sk branch releases a second one: conn = sco_conn_hold_unless_zero(conn); ... sk = sco_sock_hold(conn); sco_conn_unlock(conn); sco_conn_put(conn); if (!sk) { sco_conn_put(conn); return; } When close() races the controller's Disconnection Complete, sco_chan_del() clears conn->sk and drops the socket's reference while sco_conn_del() is running. sco_conn_del() then sees sk == NULL, its own put drops the count to zero and frees the conn, and the second put writes to the freed kref: BUG: KASAN: slab-use-after-free in sco_conn_put.part.0+0x1a/0x190 Write of size 4 at addr ffff8881099dec74 by task kworker/u17:3/413 Workqueue: hci1 hci_rx_work Call Trace: sco_conn_put.part.0+0x1a/0x190 hci_disconn_complete_evt+0x1ee/0x3e0 hci_event_packet+0x54a/0x650 hci_rx_work+0x321/0x3d0 Allocated by task 413: sco_conn_add+0x72/0x1a0 sco_connect_cfm+0x88/0x670 Freed by task 413: sco_conn_del.isra.0+0x3f/0xf0 hci_disconn_complete_evt+0x1ee/0x3e0 refcount_t: underflow; use-after-free. The root cause is that the socket stores the connection without holding a reference of its own. __sco_chan_add() does: sco_pi(sk)->conn = conn; so the socket borrows whatever reference its caller happened to hold, and the callers paper over that with ad-hoc holds and puts. Give the socket a counted reference instead: __sco_chan_add() takes one and it is released together with the channel (sco_chan_del()) and in sco_sock_destruct(). With the socket holding its own reference, sco_conn_del() no longer needs the extra put and the redundant hold in sco_conn_ready() goes away. Making the socket own its reference means the connection is now actually freed on the error paths of sco_connect() where it used to leak, which in turn runs sco_conn_free() and its hci_conn_drop(conn->hcon). To keep the hci_conn accounting balanced, make that ownership explicit as well: sco_conn_add() consumes one hci_conn reference and the sco_conn owns it for its lifetime. sco_connect() hands over the reference returned by hci_connect_sco() and no longer drops it on the error paths; sco_connect_cfm(), which is not given a reference, takes one with hci_conn_hold() before handing it to sco_conn_add() (and drops it again if the allocation fails); and the explicit hci_conn_hold() in sco_conn_ready() is removed. Every reference then has a single, clear owner. | 16 Oct |
| CVE-2026-74615 | 8.8 high | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: vxlan: do not arm the ageing timer on a device that is down vxlan_changelink() arms vxlan->age_timer whenever the requested ageing interval differs from the configured one: if (conf.age_interval != vxlan->cfg.age_interval) mod_timer(&vxlan->age_timer, jiffies); There is no netif_running() test, so the timer is armed even on a device that was never brought up. The only synchronous cancel in the driver is the timer_delete_sync() in vxlan_stop(), which is .ndo_stop. netif_close_many() drops devices without IFF_UP before __dev_close_many() runs, so that cancel is skipped for such a device. vxlan_setup() sets dev->needs_free_netdev = true and age_timer is a member of struct vxlan_dev, so free_netdev() releases the allocation the timer lives in while it is still queued on a timer_base. expire_timers() unlinks the entry before it loads timer->function, so the timer core writes through the freed object's list pointers: BUG: KASAN: slab-use-after-free in __run_timers+0x208/0x654 Write of size 8 at addr ffff00001adace68 by task true/192 __asan_store8+0x84/0xac __run_timers+0x208/0x654 run_timer_softirq+0x154/0x18c Allocated by task 189: alloc_netdev_mqs+0x64/0x720 rtnl_create_link+0x4ac/0x520 rtnl_newlink+0x758/0xd00 Freed by task 191: netdev_release+0x40/0x58 netdev_run_todo+0x4a4/0x8c0 rtnl_dellink+0x200/0x4e8 The rtnl operations involved are netns-scoped, so an unprivileged user can perform them in a new user and network namespace. Arming the timer on a down device never had an effect: vxlan_cleanup() returns early on !netif_running(), and vxlan_open() arms the timer for any non-zero interval once the device is brought up. Add the missing test. Discovered by XBOW, triaged by Baul Lee <[email protected]> | 16 Oct |
| CVE-2026-74508 | 8.8 high | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: Bluetooth: HIDP: reject frames without a transaction header hidp_recv_ctrl_frame() and hidp_recv_intr_frame() read skb->data[0] before checking that the L2CAP SDU contains a transaction header. A connected HIDP peer can send an empty basic-mode SDU and make both paths use an uninitialized byte from skb tailroom. KMSAN reports the use in hidp_session_run(), with the uninitialized value originating in __alloc_skb() through vhci_write(). The control path produces two reports and the interrupt path produces one. The byte can also be controlled by a malformed lower-layer packet. If an HCI ACL packet contains an L2CAP PDU with a declared zero-length payload followed by an extra 0x15 byte, l2cap_recv_acldata() reduces skb->len to the declared PDU length before dispatch. The current HIDP path nevertheless consumes the extra byte as HIDP_TRANS_HID_CONTROL | HIDP_CTRL_VIRTUAL_CABLE_UNPLUG and terminates the HIDP session. With this change, the same packet is discarded and a subsequent feature report request succeeds. Pull the transaction header with skb_pull_data() and discard frames that do not contain it. | 16 Oct |
| CVE-2026-74488 | 8.8 high | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: wifi: mwifiex: use the subframe length when parsing A-MSDU TDLS frames mwifiex_11n_dispatch_amsdu_pkt() splits an A-MSDU with ieee80211_amsdu_to_8023s() and walks the resulting subframes. For each subframe it passes the subframe data pointer to mwifiex_process_tdls_action_frame(), but pairs it with skb->len, the length of the A-MSDU parent, instead of rx_skb->len: rx_skb = __skb_dequeue(&list); rx_hdr = (struct rx_packet_hdr *)rx_skb->data; if (ISSUPP_TDLS_ENABLED(priv->adapter->fw_cap_info) && ntohs(rx_hdr->eth803_hdr.h_proto) == ETH_P_TDLS) { mwifiex_process_tdls_action_frame(priv, (u8 *)rx_hdr, skb->len); } The parent is not a valid description of that buffer, and may not be valid memory at all. ieee80211_amsdu_to_8023s() ends with if (!reuse_skb) dev_kfree_skb(skb); and it only sets reuse_skb when the parent is linear, is not a head_frag, and is being consumed as the *last* subframe. So when the parent does not qualify for reuse it has already been freed, and the read of skb->len is a use-after-free. When it is reused, skb->len is the length of the last subframe, applied to every earlier subframe, which over-states the buffer whenever an earlier subframe is shorter. The callee cannot absorb a wrong length, because it derives its own ceiling from the value it is given. Each frame type computes ies_len = len - sizeof(struct ethhdr) - TDLS_*_FIX_LEN; and the element walk is then bounded entirely against that ceiling, for (end = pos + ies_len; pos + 1 < end; pos += 2 + pos[1]) { u8 ie_len = pos[1]; if (pos + 2 + ie_len > end) break; so a too-large len moves end past the end of the subframe and the walk reads and copies beyond it. The A-MSDU layout is chosen by the sender, which makes the difference between the last subframe and a shorter earlier one remotely selectable. Reaching this requires TDLS support in firmware and the TDLS ethertype on the subframe. The other caller, mwifiex_process_rx_packet(), is correct: it passes a pointer and a length that describe the same region of the RX buffer. Pass rx_skb->len, the length of the subframe actually being parsed. | 16 Oct |
| CVE-2026-74443 | 8.8 high | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: drm/vmwgfx: bound DMA command body size against suffix pointer vmw_cmd_dma() locates the DMA suffix at (unsigned long) &cmd->body + header->size - sizeof(*suffix) without checking that header->size is large enough to contain both cmd->body and the suffix. An undersized header makes the suffix pointer underflow back into the previous command in the bounce buffer. The verifier later writes suffix->maximumOffset, clobbering verified fields of an already-relocated earlier command -- a TOCTOU on the device-visible command stream that lets one command rewrite another's GMR id, surface id, or other authenticated fields. Reject the command if the body is too small for the suffix to fit. | 16 Oct |
| CVE-2026-74300 | 8.8 high | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: Bluetooth: hci: validate codec capability element length Read Local Codec Capabilities returns a sequence of capability elements. Each element starts with a one-byte length followed by that many payload bytes. hci_read_codec_capabilities() checks that the skb contains the length byte, but then validates only caps->len against the remaining skb length. A malformed controller response with one remaining byte and caps->len set to one passes that check even though the element needs two bytes. The parser then records a two-byte capability and copies one byte beyond the advertised response payload into the codec list. Validate the full element size, including the length byte, before adding it to the accumulated capability length. This preserves all well-formed capability elements and drops only truncated controller responses. | 16 Oct |
| CVE-2026-72157 | 8.8 high | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: net: thunderbolt: Fix frags[] overflow by bounding frame_count tbnet_poll() assembles a multi-frame ThunderboltIP packet into one skb. The first frame goes into the skb linear area and every further frame is added as a page fragment. skb_add_rx_frag(skb, skb_shinfo(skb)->nr_frags, page, hdr_size, frame_size, TBNET_RX_PAGE_SIZE - hdr_size); A packet of frame_count frames therefore ends up with frame_count - 1 fragments. tbnet_check_frame() only bounds the peer supplied frame_count to TBNET_RING_SIZE / 4 (64), which is far above MAX_SKB_FRAGS (17 by default). A peer that sends a packet of 19 or more small frames pushes nr_frags past MAX_SKB_FRAGS, so skb_add_rx_frag() writes past skb_shinfo()->frags[] and corrupts memory after the shared info. Tighten the start of packet bound to MAX_SKB_FRAGS + 1 so a packet can never produce more fragments than frags[] can hold. This matches the recent skb frags overflow fixes in other receive paths, for example f0813bcd2d9d ("net: wwan: t7xx: fix potential skb->frags overflow in RX path") and 600dc40554dc ("net: usb: cdc-phonet: fix skb frags[] overflow in rx_complete()"). | 16 Oct |
| CVE-2026-72136 | 8.8 high | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: xfrm: xfrm_interface: require CAP_NET_ADMIN in the device netns for changelink xfrmi_changelink() operates on at most two netns, dev_net(dev) and the interface link netns xi->net. They differ once the device is created in or moved to a netns other than the one the request runs in. The rtnl changelink path checks CAP_NET_ADMIN only against dev_net(dev), so a caller privileged there but not in xi->net can rewrite an interface that lives in xi->net. Gate xfrmi_changelink() on rtnl_dev_link_net_capable() at its top, before any attribute is parsed. | 16 Oct |
Download these 1000 as CSV (the first thousand in this order) · subscribe to this list.
EPSS scores: 2026-10-30. NVD cursor: 2026-10-29 00:22. The News page shows only notable CVEs (KEV, your stack, new criticals, EPSS over 50%, or active exploitation per SSVC); this table has all of them.