Vulnerabilities
All
My stack
Known exploited
Public exploit
Critical (9+)
Likely exploited (EPSS ≥ 50%)
Changed, 24 h
New, 24 h
Sort:
risk
modified
published
CVSS
EPSS
| CVE | CVSS | EPSS | Vendor, product | Description | Modified |
|---|---|---|---|---|---|
| CVE-2026-23005exploit | 5.5 medium | 0.00% | linux, linux_kernel | In the Linux kernel, the following vulnerability has been resolved: x86/fpu: Clear XSTATE_BV[i] in guest XSAVE state whenever XFD[i]=1 When loading guest XSAVE state via KVM_SET_XSAVE, and when updating XFD in response to a guest WRMSR, clear XFD-disabled features in the saved (or to be restored) XSTATE_BV to ensure KVM doesn't attempt to load state for features that are disabled via the guest's XFD. Because the kernel executes XRSTOR with the guest's XFD, saving XSTATE_BV[i]=1 with XFD[i]=1 will cause XRSTOR to #NM and panic the kernel. E.g. if fpu_update_guest_xfd() sets XFD without clearing XSTATE_BV: ------------[ cut here ]------------ WARNING: arch/x86/kernel/traps.c:1524 at exc_device_not_available+0x101/0x110, CPU#29: amx_test/848 Modules linked in: kvm_intel kvm irqbypass CPU: 29 UID: 1000 PID: 848 Comm: amx_test Not tainted 6.19.0-rc2-ffa07f7fd437-x86_amx_nm_xfd_non_init-vm #171 NONE Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015 RIP: 0010:exc_device_not_available+0x101/0x110 Call Trace: <TASK> asm_exc_device_not_available+0x1a/0x20 RIP: 0010:restore_fpregs_from_fpstate+0x36/0x90 switch_fpu_return+0x4a/0xb0 kvm_arch_vcpu_ioctl_run+0x1245/0x1e40 [kvm] kvm_vcpu_ioctl+0x2c3/0x8f0 [kvm] __x64_sys_ioctl+0x8f/0xd0 do_syscall_64+0x62/0x940 entry_SYSCALL_64_after_hwframe+0x4b/0x53 </TASK> ---[ end trace 0000000000000000 ]--- This can happen if the guest executes WRMSR(MSR_IA32_XFD) to set XFD[18] = 1, and a host IRQ triggers kernel_fpu_begin() prior to the vmexit handler's call to fpu_update_guest_xfd(). and if userspace stuffs XSTATE_BV[i]=1 via KVM_SET_XSAVE: ------------[ cut here ]------------ WARNING: arch/x86/kernel/traps.c:1524 at exc_device_not_available+0x101/0x110, CPU#14: amx_test/867 Modules linked in: kvm_intel kvm irqbypass CPU: 14 UID: 1000 PID: 867 Comm: amx_test Not tainted 6.19.0-rc2-2dace9faccd6-x86_amx_nm_xfd_non_init-vm #168 NONE Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015 RIP: 0010:exc_device_not_available+0x101/0x110 Call Trace: <TASK> asm_exc_device_not_available+0x1a/0x20 RIP: 0010:restore_fpregs_from_fpstate+0x36/0x90 fpu_swap_kvm_fpstate+0x6b/0x120 kvm_load_guest_fpu+0x30/0x80 [kvm] kvm_arch_vcpu_ioctl_run+0x85/0x1e40 [kvm] kvm_vcpu_ioctl+0x2c3/0x8f0 [kvm] __x64_sys_ioctl+0x8f/0xd0 do_syscall_64+0x62/0x940 entry_SYSCALL_64_after_hwframe+0x4b/0x53 </TASK> ---[ end trace 0000000000000000 ]--- The new behavior is consistent with the AMX architecture. Per Intel's SDM, XSAVE saves XSTATE_BV as '0' for components that are disabled via XFD (and non-compacted XSAVE saves the initial configuration of the state component): If XSAVE, XSAVEC, XSAVEOPT, or XSAVES is saving the state component i, the instruction does not generate #NM when XCR0[i] = IA32_XFD[i] = 1; instead, it operates as if XINUSE[i] = 0 (and the state component was in its initial state): it saves bit i of XSTATE_BV field of the XSAVE header as 0; in addition, XSAVE saves the initial configuration of the state component (the other instructions do not save state component i). Alternatively, KVM could always do XRSTOR with XFD=0, e.g. by using a constant XFD based on the set of enabled features when XSAVEing for a struct fpu_guest. However, having XSTATE_BV[i]=1 for XFD-disabled features can only happen in the above interrupt case, or in similar scenarios involving preemption on preemptible kernels, because fpu_swap_kvm_fpstate()'s call to save_fpregs_to_fpstate() saves the outgoing FPU state with the current XFD; and that is (on all but the first WRMSR to XFD) the guest XFD. Therefore, XFD can only go out of sync with XSTATE_BV in the above interrupt case, or in similar scenarios involving preemption on preemptible kernels, and it we can consider it (de facto) part of KVM ABI that KVM_GET_XSAVE returns XSTATE_BV[i]=0 for XFD-disabled features. [Move clea ---truncated--- | 19 Oct |
| CVE-2021-21295 | 5.9 medium | 19.0% | netty, netapp, oncommand_api_services, oncommand_workflow_automation | Netty is an open-source, asynchronous event-driven network application framework for rapid development of maintainable high performance protocol servers & clients. In Netty (io.netty:netty-codec-http2) before version 4.1.60.Final there is a vulnerability that enables request smuggling. If a Content-Length header is present in the original HTTP/2 request, the field is not validated by `Http2MultiplexHandler` as it is propagated up. This is fine as long as the request is not proxied through as HTTP/1.1. If the request comes in as an HTTP/2 stream, gets converted into the HTTP/1.1 domain objects (`HttpRequest`, `HttpContent`, etc.) via `Http2StreamFrameToHttpObjectCodec `and then sent up to the child channel's pipeline and proxied through a remote peer as HTTP/1.1 this may result in request smuggling. In a proxy case, users may assume the content-length is validated somehow, which is not the case. If the request is forwarded to a backend channel that is a HTTP/1.1 connection, the Content-Length now has meaning and needs to be checked. An attacker can smuggle requests inside the body as it gets downgraded from HTTP/2 to HTTP/1.1. For an example attack refer to the linked GitHub Advisory. Users are only affected if all of this is true: `HTTP2MultiplexCodec` or `Http2FrameCodec` is used, `Http2StreamFrameToHttpObjectCodec` is used to convert to HTTP/1.1 objects, and these HTTP/1.1 objects are forwarded to another remote peer. This has been patched in 4.1.60.Final As a workaround, the user can do the validation by themselves by implementing a custom `ChannelInboundHandler` that is put in the `ChannelPipeline` behind `Http2StreamFrameToHttpObjectCodec`. | 8 Oct |
| CVE-2026-80528 | 9.8 critical | 1.0% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: ceph: avoid fs reclaim while using current->journal_info handle_reply() stores a `ceph_mds_request` pointer in `current->journal_info` while filling the inode and dentry cache from an MDS reply. An allocation in this section can enter direct reclaim and prune dentries from another filesystem. If this dirties an ext4 inode, ext4 starts a JBD2 transaction. JBD2 interprets the Ceph request in `current->journal_info` as a journal handle and dereferences the request's `r_tid` as `h_transaction`, causing a kernel crash, e.g.: Unable to handle kernel paging request at virtual address 00000000077b4818 [...] Internal error: Oops: 0000000096000004 [#1] SMP Modules linked in: CPU: 6 UID: 0 PID: 2699135 Comm: kworker/6:3 Tainted: G W 6.18.38-i3 #1113 NONE [...] Workqueue: ceph-msgr ceph_con_workfn pstate: 80400009 (Nzcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : jbd2__journal_start+0x2c/0x208 lr : __ext4_journal_start_sb+0x100/0x178 [...] Call trace: jbd2__journal_start+0x2c/0x208 (P) __ext4_journal_start_sb+0x100/0x178 ext4_dirty_inode+0x3c/0x90 __mark_inode_dirty+0x58/0x400 iput.part.0+0x2b0/0x370 iput+0x18/0x30 dentry_unlink_inode+0xc0/0x158 __dentry_kill+0x80/0x250 shrink_dentry_list+0x90/0x130 prune_dcache_sb+0x60/0x98 super_cache_scan+0xe8/0x190 do_shrink_slab+0x174/0x388 shrink_slab+0xd8/0x4c0 shrink_node+0x31c/0x908 do_try_to_free_pages+0xd0/0x508 try_to_free_pages+0x11c/0x238 __alloc_frozen_pages_noprof+0x4d0/0xdd0 __folio_alloc_noprof+0x18/0x70 __filemap_get_folio+0x248/0x440 ceph_readdir_prepopulate+0x570/0x9e8 mds_dispatch+0x1424/0x1ba0 ceph_con_process_message+0x74/0xa0 ceph_con_v1_try_read+0x3a0/0x1510 ceph_con_workfn+0x260/0x460 Enter a scoped NOFS allocation context and leave it after clearing `journal_info`. This prevents filesystem reclaim from recursing into another filesystem while the field contains Ceph-private data. | 16 Oct |
| CVE-2026-103646 | 9.8 critical | 0.00% | no CPE yet | The Ultimate Multisite WordPress plugin before 2.17.0 does not require authentication before a logged-out checkout is linked to, and logged in as, an existing WordPress account matching the submitted email address, and its duplicate-account check normalizes that address differently from the lookup used to create the customer, so an unauthenticated attacker can log in as any existing user, including a Network Super Admin, whose email address they know. This bypass is not addressed by the 2.15.1 fix for CVE-2026-75957 and remains exploitable in all versions up to and including 2.16.1, the releases that fix was expected to cover. Exploitation requires a checkout form configured without a password field (auto-generated password) and a target account that has no existing customer record in the Ultimate Multisite WordPress plugin before 2.17.0. | 8 Oct |
| CVE-2025-71123 | 7.8 high | 0.00% | linux, linux_kernel | In the Linux kernel, the following vulnerability has been resolved: ext4: fix string copying in parse_apply_sb_mount_options() strscpy_pad() can't be used to copy a non-NUL-term string into a NUL-term string of possibly bigger size. Commit 0efc5990bca5 ("string.h: Introduce memtostr() and memtostr_pad()") provides additional information in that regard. So if this happens, the following warning is observed: strnlen: detected buffer overflow: 65 byte read of buffer size 64 WARNING: CPU: 0 PID: 28655 at lib/string_helpers.c:1032 __fortify_report+0x96/0xc0 lib/string_helpers.c:1032 Modules linked in: CPU: 0 UID: 0 PID: 28655 Comm: syz-executor.3 Not tainted 6.12.54-syzkaller-00144-g5f0270f1ba00 #0 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 RIP: 0010:__fortify_report+0x96/0xc0 lib/string_helpers.c:1032 Call Trace: <TASK> __fortify_panic+0x1f/0x30 lib/string_helpers.c:1039 strnlen include/linux/fortify-string.h:235 [inline] sized_strscpy include/linux/fortify-string.h:309 [inline] parse_apply_sb_mount_options fs/ext4/super.c:2504 [inline] __ext4_fill_super fs/ext4/super.c:5261 [inline] ext4_fill_super+0x3c35/0xad00 fs/ext4/super.c:5706 get_tree_bdev_flags+0x387/0x620 fs/super.c:1636 vfs_get_tree+0x93/0x380 fs/super.c:1814 do_new_mount fs/namespace.c:3553 [inline] path_mount+0x6ae/0x1f70 fs/namespace.c:3880 do_mount fs/namespace.c:3893 [inline] __do_sys_mount fs/namespace.c:4103 [inline] __se_sys_mount fs/namespace.c:4080 [inline] __x64_sys_mount+0x280/0x300 fs/namespace.c:4080 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0x64/0x140 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x76/0x7e Since userspace is expected to provide s_mount_opts field to be at most 63 characters long with the ending byte being NUL-term, use a 64-byte buffer which matches the size of s_mount_opts, so that strscpy_pad() does its job properly. Return with error if the user still managed to provide a non-NUL-term string here. Found by Linux Verification Center (linuxtesting.org) with Syzkaller. | 15 Oct |
| CVE-2024-26907 | 7.8 high | 0.00% | linux, linux_kernel | In the Linux kernel, the following vulnerability has been resolved: RDMA/mlx5: Fix fortify source warning while accessing Eth segment ------------[ cut here ]------------ memcpy: detected field-spanning write (size 56) of single field "eseg->inline_hdr.start" at /var/lib/dkms/mlnx-ofed-kernel/5.8/build/drivers/infiniband/hw/mlx5/wr.c:131 (size 2) WARNING: CPU: 0 PID: 293779 at /var/lib/dkms/mlnx-ofed-kernel/5.8/build/drivers/infiniband/hw/mlx5/wr.c:131 mlx5_ib_post_send+0x191b/0x1a60 [mlx5_ib] Modules linked in: 8021q garp mrp stp llc rdma_ucm(OE) rdma_cm(OE) iw_cm(OE) ib_ipoib(OE) ib_cm(OE) ib_umad(OE) mlx5_ib(OE) ib_uverbs(OE) ib_core(OE) mlx5_core(OE) pci_hyperv_intf mlxdevm(OE) mlx_compat(OE) tls mlxfw(OE) psample nft_fib_inet nft_fib_ipv4 nft_fib_ipv6 nft_fib nft_reject_inet nf_reject_ipv4 nf_reject_ipv6 nft_reject nft_ct nft_chain_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 ip_set nf_tables libcrc32c nfnetlink mst_pciconf(OE) knem(OE) vfio_pci vfio_pci_core vfio_iommu_type1 vfio iommufd irqbypass cuse nfsv3 nfs fscache netfs xfrm_user xfrm_algo ipmi_devintf ipmi_msghandler binfmt_misc crct10dif_pclmul crc32_pclmul polyval_clmulni polyval_generic ghash_clmulni_intel sha512_ssse3 snd_pcsp aesni_intel crypto_simd cryptd snd_pcm snd_timer joydev snd soundcore input_leds serio_raw evbug nfsd auth_rpcgss nfs_acl lockd grace sch_fq_codel sunrpc drm efi_pstore ip_tables x_tables autofs4 psmouse virtio_net net_failover failover floppy [last unloaded: mlx_compat(OE)] CPU: 0 PID: 293779 Comm: ssh Tainted: G OE 6.2.0-32-generic #32~22.04.1-Ubuntu Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011 RIP: 0010:mlx5_ib_post_send+0x191b/0x1a60 [mlx5_ib] Code: 0c 01 00 a8 01 75 25 48 8b 75 a0 b9 02 00 00 00 48 c7 c2 10 5b fd c0 48 c7 c7 80 5b fd c0 c6 05 57 0c 03 00 01 e8 95 4d 93 da <0f> 0b 44 8b 4d b0 4c 8b 45 c8 48 8b 4d c0 e9 49 fb ff ff 41 0f b7 RSP: 0018:ffffb5b48478b570 EFLAGS: 00010046 RAX: 0000000000000000 RBX: 0000000000000001 RCX: 0000000000000000 RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000 RBP: ffffb5b48478b628 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000000 R12: ffffb5b48478b5e8 R13: ffff963a3c609b5e R14: ffff9639c3fbd800 R15: ffffb5b480475a80 FS: 00007fc03b444c80(0000) GS:ffff963a3dc00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000556f46bdf000 CR3: 0000000006ac6003 CR4: 00000000003706f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> ? show_regs+0x72/0x90 ? mlx5_ib_post_send+0x191b/0x1a60 [mlx5_ib] ? __warn+0x8d/0x160 ? mlx5_ib_post_send+0x191b/0x1a60 [mlx5_ib] ? report_bug+0x1bb/0x1d0 ? handle_bug+0x46/0x90 ? exc_invalid_op+0x19/0x80 ? asm_exc_invalid_op+0x1b/0x20 ? mlx5_ib_post_send+0x191b/0x1a60 [mlx5_ib] mlx5_ib_post_send_nodrain+0xb/0x20 [mlx5_ib] ipoib_send+0x2ec/0x770 [ib_ipoib] ipoib_start_xmit+0x5a0/0x770 [ib_ipoib] dev_hard_start_xmit+0x8e/0x1e0 ? validate_xmit_skb_list+0x4d/0x80 sch_direct_xmit+0x116/0x3a0 __dev_xmit_skb+0x1fd/0x580 __dev_queue_xmit+0x284/0x6b0 ? _raw_spin_unlock_irq+0xe/0x50 ? __flush_work.isra.0+0x20d/0x370 ? push_pseudo_header+0x17/0x40 [ib_ipoib] neigh_connected_output+0xcd/0x110 ip_finish_output2+0x179/0x480 ? __smp_call_single_queue+0x61/0xa0 __ip_finish_output+0xc3/0x190 ip_finish_output+0x2e/0xf0 ip_output+0x78/0x110 ? __pfx_ip_finish_output+0x10/0x10 ip_local_out+0x64/0x70 __ip_queue_xmit+0x18a/0x460 ip_queue_xmit+0x15/0x30 __tcp_transmit_skb+0x914/0x9c0 tcp_write_xmit+0x334/0x8d0 tcp_push_one+0x3c/0x60 tcp_sendmsg_locked+0x2e1/0xac0 tcp_sendmsg+0x2d/0x50 inet_sendmsg+0x43/0x90 sock_sendmsg+0x68/0x80 sock_write_iter+0x93/0x100 vfs_write+0x326/0x3c0 ksys_write+0xbd/0xf0 ? do_syscall_64+0x69/0x90 __x64_sys_write+0x19/0x30 do_syscall_ ---truncated--- | 15 Oct |
| CVE-2026-53726 | 6.9 medium | 0.00% | no CPE yet | Parse Server is an open source backend that can be deployed to any infrastructure that can run Node.js. Prior to versions 8.6.80 and 9.9.1-alpha.6, a relation query using the $relatedTo operator could read the membership of a Relation field even when that field was hidden from the requesting client by protectedFields, and even when the object owning the relation was not readable by the client under its ACL or class-level permissions. The request requires only the public API credentials that Parse clients normally carry — no user session, master key, or Cloud Code is needed. As a result, an unauthenticated client who knows or obtains the owning object's objectId could enumerate the objects linked through a protected relation, or combine the operator with an objectId constraint to use it as a membership oracle — confirming whether a specific object is linked to a private parent. This affects applications that rely on protectedFields or object ACLs to keep Relation membership confidential, such as private group memberships, block lists, or account-to-resource associations. This issue has been patched in versions 8.6.80 and 9.9.1-alpha.6. | Mon 26 Oct |
| CVE-2022-49979 | 5.5 medium | 0.00% | linux, linux_kernel | In the Linux kernel, the following vulnerability has been resolved: net: fix refcount bug in sk_psock_get (2) Syzkaller reports refcount bug as follows: ------------[ cut here ]------------ refcount_t: saturated; leaking memory. WARNING: CPU: 1 PID: 3605 at lib/refcount.c:19 refcount_warn_saturate+0xf4/0x1e0 lib/refcount.c:19 Modules linked in: CPU: 1 PID: 3605 Comm: syz-executor208 Not tainted 5.18.0-syzkaller-03023-g7e062cda7d90 #0 <TASK> __refcount_add_not_zero include/linux/refcount.h:163 [inline] __refcount_inc_not_zero include/linux/refcount.h:227 [inline] refcount_inc_not_zero include/linux/refcount.h:245 [inline] sk_psock_get+0x3bc/0x410 include/linux/skmsg.h:439 tls_data_ready+0x6d/0x1b0 net/tls/tls_sw.c:2091 tcp_data_ready+0x106/0x520 net/ipv4/tcp_input.c:4983 tcp_data_queue+0x25f2/0x4c90 net/ipv4/tcp_input.c:5057 tcp_rcv_state_process+0x1774/0x4e80 net/ipv4/tcp_input.c:6659 tcp_v4_do_rcv+0x339/0x980 net/ipv4/tcp_ipv4.c:1682 sk_backlog_rcv include/net/sock.h:1061 [inline] __release_sock+0x134/0x3b0 net/core/sock.c:2849 release_sock+0x54/0x1b0 net/core/sock.c:3404 inet_shutdown+0x1e0/0x430 net/ipv4/af_inet.c:909 __sys_shutdown_sock net/socket.c:2331 [inline] __sys_shutdown_sock net/socket.c:2325 [inline] __sys_shutdown+0xf1/0x1b0 net/socket.c:2343 __do_sys_shutdown net/socket.c:2351 [inline] __se_sys_shutdown net/socket.c:2349 [inline] __x64_sys_shutdown+0x50/0x70 net/socket.c:2349 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x46/0xb0 </TASK> During SMC fallback process in connect syscall, kernel will replaces TCP with SMC. In order to forward wakeup smc socket waitqueue after fallback, kernel will sets clcsk->sk_user_data to origin smc socket in smc_fback_replace_callbacks(). Later, in shutdown syscall, kernel will calls sk_psock_get(), which treats the clcsk->sk_user_data as psock type, triggering the refcnt warning. So, the root cause is that smc and psock, both will use sk_user_data field. So they will mismatch this field easily. This patch solves it by using another bit(defined as SK_USER_DATA_PSOCK) in PTRMASK, to mark whether sk_user_data points to a psock object or not. This patch depends on a PTRMASK introduced in commit f1ff5ce2cd5e ("net, sk_msg: Clear sk_user_data pointer on clone if tagged"). For there will possibly be more flags in the sk_user_data field, this patch also refactor sk_user_data flags code to be more generic to improve its maintainability. | 15 Oct |
| CVE-2026-43080 | 5.5 medium | 0.00% | linux, linux_kernel | In the Linux kernel, the following vulnerability has been resolved: l2tp: Drop large packets with UDP encap syzbot reported a WARN on my patch series [1]. The actual issue is an overflow of 16-bit UDP length field, and it exists in the upstream code. My series added a debug WARN with an overflow check that exposed the issue, that's why syzbot tripped on my patches, rather than on upstream code. syzbot's repro: r0 = socket$pppl2tp(0x18, 0x1, 0x1) r1 = socket$inet6_udp(0xa, 0x2, 0x0) connect$inet6(r1, &(0x7f00000000c0)={0xa, 0x0, 0x0, @loopback, 0xfffffffc}, 0x1c) connect$pppl2tp(r0, &(0x7f0000000240)=@pppol2tpin6={0x18, 0x1, {0x0, r1, 0x4, 0x0, 0x0, 0x0, {0xa, 0x4e22, 0xffff, @ipv4={'\x00', '\xff\xff', @empty}}}}, 0x32) writev(r0, &(0x7f0000000080)=[{&(0x7f0000000000)="ee", 0x34000}], 0x1) It basically sends an oversized (0x34000 bytes) PPPoL2TP packet with UDP encapsulation, and l2tp_xmit_core doesn't check for overflows when it assigns the UDP length field. The value gets trimmed to 16 bites. Add an overflow check that drops oversized packets and avoids sending packets with trimmed UDP length to the wire. syzbot's stack trace (with my patch applied): len >= 65536u WARNING: ./include/linux/udp.h:38 at udp_set_len_short include/linux/udp.h:38 [inline], CPU#1: syz.0.17/5957 WARNING: ./include/linux/udp.h:38 at l2tp_xmit_core net/l2tp/l2tp_core.c:1293 [inline], CPU#1: syz.0.17/5957 WARNING: ./include/linux/udp.h:38 at l2tp_xmit_skb+0x1204/0x18d0 net/l2tp/l2tp_core.c:1327, CPU#1: syz.0.17/5957 Modules linked in: CPU: 1 UID: 0 PID: 5957 Comm: syz.0.17 Not tainted syzkaller #0 PREEMPT(full) Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.2-debian-1.16.2-1 04/01/2014 RIP: 0010:udp_set_len_short include/linux/udp.h:38 [inline] RIP: 0010:l2tp_xmit_core net/l2tp/l2tp_core.c:1293 [inline] RIP: 0010:l2tp_xmit_skb+0x1204/0x18d0 net/l2tp/l2tp_core.c:1327 Code: 0f 0b 90 e9 21 f9 ff ff e8 e9 05 ec f6 90 0f 0b 90 e9 8d f9 ff ff e8 db 05 ec f6 90 0f 0b 90 e9 cc f9 ff ff e8 cd 05 ec f6 90 <0f> 0b 90 e9 de fa ff ff 44 89 f1 80 e1 07 80 c1 03 38 c1 0f 8c 4f RSP: 0018:ffffc90003d67878 EFLAGS: 00010293 RAX: ffffffff8ad985e3 RBX: ffff8881a6400090 RCX: ffff8881697f0000 RDX: 0000000000000000 RSI: 0000000000034010 RDI: 000000000000ffff RBP: dffffc0000000000 R08: 0000000000000003 R09: 0000000000000004 R10: dffffc0000000000 R11: fffff520007acf00 R12: ffff8881baf20900 R13: 0000000000034010 R14: ffff8881a640008e R15: ffff8881760f7000 FS: 000055557e81f500(0000) GS:ffff8882a9467000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000200000033000 CR3: 00000001612f4000 CR4: 00000000000006f0 Call Trace: <TASK> pppol2tp_sendmsg+0x40a/0x5f0 net/l2tp/l2tp_ppp.c:302 sock_sendmsg_nosec net/socket.c:727 [inline] __sock_sendmsg net/socket.c:742 [inline] sock_write_iter+0x503/0x550 net/socket.c:1195 do_iter_readv_writev+0x619/0x8c0 fs/read_write.c:-1 vfs_writev+0x33c/0x990 fs/read_write.c:1059 do_writev+0x154/0x2e0 fs/read_write.c:1105 do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline] do_syscall_64+0x14d/0xf80 arch/x86/entry/syscall_64.c:94 entry_SYSCALL_64_after_hwframe+0x77/0x7f RIP: 0033:0x7f636479c629 Code: ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 e8 ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007ffffd4241c8 EFLAGS: 00000246 ORIG_RAX: 0000000000000014 RAX: ffffffffffffffda RBX: 00007f6364a15fa0 RCX: 00007f636479c629 RDX: 0000000000000001 RSI: 0000200000000080 RDI: 0000000000000003 RBP: 00007f6364832b39 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000 R13: 00007f6364a15fac R14: 00007f6364a15fa0 R15: 00007f6364a15fa0 </TASK> [1]: https://lore.kernel.org/all/[email protected]/ | 15 Oct |
| CVE-2024-39509 | 5.5 medium | 0.00% | linux, linux_kernel | In the Linux kernel, the following vulnerability has been resolved: HID: core: remove unnecessary WARN_ON() in implement() Syzkaller hit a warning [1] in a call to implement() when trying to write a value into a field of smaller size in an output report. Since implement() already has a warn message printed out with the help of hid_warn() and value in question gets trimmed with: ... value &= m; ... WARN_ON may be considered superfluous. Remove it to suppress future syzkaller triggers. [1] WARNING: CPU: 0 PID: 5084 at drivers/hid/hid-core.c:1451 implement drivers/hid/hid-core.c:1451 [inline] WARNING: CPU: 0 PID: 5084 at drivers/hid/hid-core.c:1451 hid_output_report+0x548/0x760 drivers/hid/hid-core.c:1863 Modules linked in: CPU: 0 PID: 5084 Comm: syz-executor424 Not tainted 6.9.0-rc7-syzkaller-00183-gcf87f46fd34d #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 04/02/2024 RIP: 0010:implement drivers/hid/hid-core.c:1451 [inline] RIP: 0010:hid_output_report+0x548/0x760 drivers/hid/hid-core.c:1863 ... Call Trace: <TASK> __usbhid_submit_report drivers/hid/usbhid/hid-core.c:591 [inline] usbhid_submit_report+0x43d/0x9e0 drivers/hid/usbhid/hid-core.c:636 hiddev_ioctl+0x138b/0x1f00 drivers/hid/usbhid/hiddev.c:726 vfs_ioctl fs/ioctl.c:51 [inline] __do_sys_ioctl fs/ioctl.c:904 [inline] __se_sys_ioctl+0xfc/0x170 fs/ioctl.c:890 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf5/0x240 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f ... | 15 Oct |
| CVE-2026-107259 | unscored | 0.00% | drupal, linked field | Improper Neutralization of Special Elements Used in a Template Engine vulnerability in Drupal Linked Field allows Code Injection. This issue affects Linked Field versions: from 0.0.0 to 1.8.0. | Fri 30 Oct |
| CVE-2026-98884 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: mmc: core: Add validation for host-provided max_segs The max_segs field is of type unsigned short, and if a host driver sets an excessively large value, it may be truncated to zero. This can cause mmc_alloc_sg() to call kmalloc_objs() with a zero size allocation request, which leads to undefined behavior. Under the SLUB allocator, kmalloc(0) returns a special pointer (ZERO_SIZE_PTR). The subsequent 'if (sg)' check will evaluate to true, and sg_init_table() will then attempt to access invalid memory, resulting in a crash: dwmmc_rockchip 2a310000.mmc: Successfully tuned phase to 133 mmc1: new UHS-I speed SDR104 SDHC card at address aaaa Unable to handle kernel paging request at virtual address 0000001ffffffff0 Mem abort info: ESR = 0x0000000096000004 EC = 0x25: DABT (current EL), IL = 32 bits SET = 0, FnV = 0 EA = 0, S1PTW = 0 FSC = 0x04: level 0 translation fault Data abort info: ISV = 0, ISS = 0x00000004, ISS2 = 0x00000000 CM = 0, WnR = 0, TnD = 0, TagAccess = 0 GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0 user pgtable: 4k pages, 48-bit VAs, pgdp=0000000102c88000 [0000001ffffffff0] pgd=0000000000000000, p4d=0000000000000000 Internal error: Oops: 0000000096000004 [#1] SMP Modules linked in: CPU: 2 UID: 0 PID: 102 Comm: kworker/2:1 Not tainted 7.0.0-rc6-next-20260331-00013-g4d93c25963c5-dirty #80 PREEMPT Hardware name: Rockchip RK3576 EVB V10 Board (DT) Workqueue: events_freezable mmc_rescan pstate: 80000005 (Nzcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : sg_init_table+0x2c/0x50 lr : sg_init_table+0x24/0x50 sp : ffff8000837db710 x29: ffff8000837db710 x28: 000000000000c000 x27: 0000000000000300 x26: 0000000000000000 x25: 0000000000000040 x24: ffff0000c46a0000 x23: 0000000000000000 x22: ffff0000c0c73c00 x21: 0000000000000010 x20: 0000000000000010 x19: 0000000000000000 x18: 000000000000002c x17: 0000000000000000 x16: 0000000000000001 x15: 0000000000000000 x14: 0000000000000400 x13: ffff8000837dc000 x12: 0000000000000000 x11: ffff0000c0c73ca0 x10: 0000000000000040 x9 : 459ec1f0abbdbb00 x8 : 0000001fffffffe0 x7 : 0000000000000000 x6 : 000000000000003f x5 : 0000000000035579 x4 : 0000000000000901 x3 : 0000000000000000 x2 : 0000000000000000 x1 : 0000000000000000 x0 : 0000000000000010 Call trace: sg_init_table+0x2c/0x50 (P) mmc_mq_init_request+0x64/0x90 blk_mq_alloc_map_and_rqs+0x3ac/0x480 blk_mq_alloc_set_map_and_rqs+0x98/0x1e0 blk_mq_alloc_tag_set+0x1c0/0x290 mmc_init_queue+0x120/0x370 mmc_blk_alloc_req+0x150/0x420 To prevent this, add a validation check in mmc_mq_init_request() to detect when sg_len (derived from max_segs) is zero. If sg_len is zero, we return an error and print an error message, allowing host driver developers to identify and fix incorrect max_segs configuration. This is a defensive measure that ensures the MMC core fails gracefully when host drivers provide invalid max_segs values, rather than crashing with a page fault. | Mon 26 Oct |
| CVE-2025-40016 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: media: uvcvideo: Mark invalid entities with id UVC_INVALID_ENTITY_ID Per UVC 1.1+ specification 3.7.2, units and terminals must have a non-zero unique ID. ``` Each Unit and Terminal within the video function is assigned a unique identification number, the Unit ID (UID) or Terminal ID (TID), contained in the bUnitID or bTerminalID field of the descriptor. The value 0x00 is reserved for undefined ID, ``` If we add a new entity with id 0 or a duplicated ID, it will be marked as UVC_INVALID_ENTITY_ID. In a previous attempt commit 3dd075fe8ebb ("media: uvcvideo: Require entities to have a non-zero unique ID"), we ignored all the invalid units, this broke a lot of non-compatible cameras. Hopefully we are more lucky this time. This also prevents some syzkaller reproducers from triggering warnings due to a chain of entities referring to themselves. In one particular case, an Output Unit is connected to an Input Unit, both with the same ID of 1. But when looking up for the source ID of the Output Unit, that same entity is found instead of the input entity, which leads to such warnings. In another case, a backward chain was considered finished as the source ID was 0. Later on, that entity was found, but its pads were not valid. Here is a sample stack trace for one of those cases. [ 20.650953] usb 1-1: new high-speed USB device number 2 using dummy_hcd [ 20.830206] usb 1-1: Using ep0 maxpacket: 8 [ 20.833501] usb 1-1: config 0 descriptor?? [ 21.038518] usb 1-1: string descriptor 0 read error: -71 [ 21.038893] usb 1-1: Found UVC 0.00 device <unnamed> (2833:0201) [ 21.039299] uvcvideo 1-1:0.0: Entity type for entity Output 1 was not initialized! [ 21.041583] uvcvideo 1-1:0.0: Entity type for entity Input 1 was not initialized! [ 21.042218] ------------[ cut here ]------------ [ 21.042536] WARNING: CPU: 0 PID: 9 at drivers/media/mc/mc-entity.c:1147 media_create_pad_link+0x2c4/0x2e0 [ 21.043195] Modules linked in: [ 21.043535] CPU: 0 UID: 0 PID: 9 Comm: kworker/0:1 Not tainted 6.11.0-rc7-00030-g3480e43aeccf #444 [ 21.044101] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.15.0-1 04/01/2014 [ 21.044639] Workqueue: usb_hub_wq hub_event [ 21.045100] RIP: 0010:media_create_pad_link+0x2c4/0x2e0 [ 21.045508] Code: fe e8 20 01 00 00 b8 f4 ff ff ff 48 83 c4 30 5b 41 5c 41 5d 41 5e 41 5f 5d c3 cc cc cc cc 0f 0b eb e9 0f 0b eb 0a 0f 0b eb 06 <0f> 0b eb 02 0f 0b b8 ea ff ff ff eb d4 66 2e 0f 1f 84 00 00 00 00 [ 21.046801] RSP: 0018:ffffc9000004b318 EFLAGS: 00010246 [ 21.047227] RAX: ffff888004e5d458 RBX: 0000000000000000 RCX: ffffffff818fccf1 [ 21.047719] RDX: 000000000000007b RSI: 0000000000000000 RDI: ffff888004313290 [ 21.048241] RBP: ffff888004313290 R08: 0001ffffffffffff R09: 0000000000000000 [ 21.048701] R10: 0000000000000013 R11: 0001888004313290 R12: 0000000000000003 [ 21.049138] R13: ffff888004313080 R14: ffff888004313080 R15: 0000000000000000 [ 21.049648] FS: 0000000000000000(0000) GS:ffff88803ec00000(0000) knlGS:0000000000000000 [ 21.050271] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 21.050688] CR2: 0000592cc27635b0 CR3: 000000000431c000 CR4: 0000000000750ef0 [ 21.051136] PKRU: 55555554 [ 21.051331] Call Trace: [ 21.051480] <TASK> [ 21.051611] ? __warn+0xc4/0x210 [ 21.051861] ? media_create_pad_link+0x2c4/0x2e0 [ 21.052252] ? report_bug+0x11b/0x1a0 [ 21.052540] ? trace_hardirqs_on+0x31/0x40 [ 21.052901] ? handle_bug+0x3d/0x70 [ 21.053197] ? exc_invalid_op+0x1a/0x50 [ 21.053511] ? asm_exc_invalid_op+0x1a/0x20 [ 21.053924] ? media_create_pad_link+0x91/0x2e0 [ 21.054364] ? media_create_pad_link+0x2c4/0x2e0 [ 21.054834] ? media_create_pad_link+0x91/0x2e0 [ 21.055131] ? _raw_spin_unlock+0x1e/0x40 [ 21.055441] ? __v4l2_device_register_subdev+0x202/0x210 [ 21.055837] uvc_mc_register_entities+0x358/0x400 [ 21.056144] uvc_register_chains+0x1 ---truncated--- | 19 Oct |
| CVE-2025-40181 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: x86/kvm: Force legacy PCI hole to UC when overriding MTRRs for TDX/SNP When running as an SNP or TDX guest under KVM, force the legacy PCI hole, i.e. memory between Top of Lower Usable DRAM and 4GiB, to be mapped as UC via a forced variable MTRR range. In most KVM-based setups, legacy devices such as the HPET and TPM are enumerated via ACPI. ACPI enumeration includes a Memory32Fixed entry, and optionally a SystemMemory descriptor for an OperationRegion, e.g. if the device needs to be accessed via a Control Method. If a SystemMemory entry is present, then the kernel's ACPI driver will auto-ioremap the region so that it can be accessed at will. However, the ACPI spec doesn't provide a way to enumerate the memory type of SystemMemory regions, i.e. there's no way to tell software that a region must be mapped as UC vs. WB, etc. As a result, Linux's ACPI driver always maps SystemMemory regions using ioremap_cache(), i.e. as WB on x86. The dedicated device drivers however, e.g. the HPET driver and TPM driver, want to map their associated memory as UC or WC, as accessing PCI devices using WB is unsupported. On bare metal and non-CoCO, the conflicting requirements "work" as firmware configures the PCI hole (and other device memory) to be UC in the MTRRs. So even though the ACPI mappings request WB, they are forced to UC- in the kernel's tracking due to the kernel properly handling the MTRR overrides, and thus are compatible with the drivers' requested WC/UC-. With force WB MTRRs on SNP and TDX guests, the ACPI mappings get their requested WB if the ACPI mappings are established before the dedicated driver code attempts to initialize the device. E.g. if acpi_init() runs before the corresponding device driver is probed, ACPI's WB mapping will "win", and result in the driver's ioremap() failing because the existing WB mapping isn't compatible with the requested WC/UC-. E.g. when a TPM is emulated by the hypervisor (ignoring the security implications of relying on what is allegedly an untrusted entity to store measurements), the TPM driver will request UC and fail: [ 1.730459] ioremap error for 0xfed40000-0xfed45000, requested 0x2, got 0x0 [ 1.732780] tpm_tis MSFT0101:00: probe with driver tpm_tis failed with error -12 Note, the '0x2' and '0x0' values refer to "enum page_cache_mode", not x86's memtypes (which frustratingly are an almost pure inversion; 2 == WB, 0 == UC). E.g. tracing mapping requests for TPM TIS yields: Mapping TPM TIS with req_type = 0 WARNING: CPU: 22 PID: 1 at arch/x86/mm/pat/memtype.c:530 memtype_reserve+0x2ab/0x460 Modules linked in: CPU: 22 UID: 0 PID: 1 Comm: swapper/0 Tainted: G W 6.16.0-rc7+ #2 VOLUNTARY Tainted: [W]=WARN Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 05/29/2025 RIP: 0010:memtype_reserve+0x2ab/0x460 __ioremap_caller+0x16d/0x3d0 ioremap_cache+0x17/0x30 x86_acpi_os_ioremap+0xe/0x20 acpi_os_map_iomem+0x1f3/0x240 acpi_os_map_memory+0xe/0x20 acpi_ex_system_memory_space_handler+0x273/0x440 acpi_ev_address_space_dispatch+0x176/0x4c0 acpi_ex_access_region+0x2ad/0x530 acpi_ex_field_datum_io+0xa2/0x4f0 acpi_ex_extract_from_field+0x296/0x3e0 acpi_ex_read_data_from_field+0xd1/0x460 acpi_ex_resolve_node_to_value+0x2ee/0x530 acpi_ex_resolve_to_value+0x1f2/0x540 acpi_ds_evaluate_name_path+0x11b/0x190 acpi_ds_exec_end_op+0x456/0x960 acpi_ps_parse_loop+0x27a/0xa50 acpi_ps_parse_aml+0x226/0x600 acpi_ps_execute_method+0x172/0x3e0 acpi_ns_evaluate+0x175/0x5f0 acpi_evaluate_object+0x213/0x490 acpi_evaluate_integer+0x6d/0x140 acpi_bus_get_status+0x93/0x150 acpi_add_single_object+0x43a/0x7c0 acpi_bus_check_add+0x149/0x3a0 acpi_bus_check_add_1+0x16/0x30 acpi_ns_walk_namespace+0x22c/0x360 acpi_walk_namespace+0x15c/0x170 acpi_bus_scan+0x1dd/0x200 acpi_scan_init+0xe5/0x2b0 acpi_init+0x264/0x5b0 do_one_i ---truncated--- | 19 Oct |
| CVE-2026-97936 | unscored | 0.00% | no CPE yet | In the Linux kernel, the following vulnerability has been resolved: tracing: Fix memory corruption from the histogram stacktrace modifier parse_field() sets HIST_FIELD_FL_STACKTRACE from the ".stacktrace" modifier before it looks the field name up, and nothing afterwards checks that the name resolved to a field which holds a stacktrace. create_hist_field() picks HIST_FIELD_FN_STACK on the strength of the field pointer alone, which reads a __data_loc word from the record and follows its low 16 bits as an offset into the same record. event_hist_trigger() takes the first word there as an entry count and copies that many longs into a 31 entry array: n_entries = *stack; memcpy(entries, ++stack, n_entries * sizeof(unsigned long)); Neither end of that copy is bounded, and the count is whatever the event holds at the offset, so any field will do: # cd /sys/kernel/tracing/events/sched/sched_process_fork # echo 'hist:keys=parent_pid.stacktrace' > trigger # (true) BUG: kernel NULL pointer dereference, address: 0000000000000008 RIP: 0010:rb_insert_color+0x18/0x130 timerqueue_linked_add+0x7e/0xd0 enqueue_hrtimer+0x39/0xb0 __hrtimer_run_queues+0x10f/0x1f0 </IRQ> RIP: 0010:memcpy+0xc/0x30 event_hist_trigger+0x165/0x690 The timer interrupt landed on the rbtree the copy had already run over. No debug options are needed for this; KASAN reports the same write as an out-of-bounds read of 13835058055416381440 bytes. Documentation/trace/histogram.rst already states the rule, "must be a long[] type", so enforce it once the name has been resolved. Names which resolve to no field at all, "hitcount.stacktrace" and the common_* pseudo-fields, are refused for the same reason: they hold no stacktrace to read. | 19 Oct |
15 of 15
Download these 15 as CSV · subscribe to this list.
EPSS scores: 2026-10-31. NVD cursor: 2026-10-29 00:22. The News page shows only notable CVEs (KEV, your stack, new criticals, EPSS over 50%, or active exploitation per SSVC); this table has all of them.