Vulnerabilities
All
My stack
Known exploited
Public exploit
Critical (9+)
Likely exploited (EPSS ≥ 50%)
Changed, 24 h
New, 24 h
Sort:
risk
modified
published
CVSS
EPSS
| CVE | CVSS | EPSS | Vendor, product | Description | Modified |
|---|---|---|---|---|---|
| CVE-2026-118057 | 7.2 high | 0.00% | paultgoodchild, shield security – smart bot blocking, brute-force login protection & file scanning | The Shield Security – Smart Bot Blocking, Brute-Force Login Protection & File Scanning plugin for WordPress is vulnerable to Stored Cross-Site Scripting via the 'REQUEST_URI' parameter in all versions up to, and including, 22.3.2 due to insufficient input sanitization and output escaping. This makes it possible for unauthenticated attackers to inject arbitrary web scripts in pages that will execute whenever a user accesses an injected page. The hidden 'path' column in ForTraffic.php lacks a client-side render function, so DataTables builds its cell via innerHTML, causing stored HTML in the path value to be parsed into live DOM nodes; a prior partial fix in version 18.5.8 added esc_html() only to the visible 'page' column, leaving the hidden 'path' field unescaped and exploitable through version 22.2.6. | Sat 31 Oct |
| CVE-2024-58360 | 6.9 medium | 0.00% | no CPE yet | stoatchat versions before 0.7.8 fail to enforce account creation restrictions including invite-only mode, email verification, captcha, and shield verification. Attackers can create unlimited accounts with unverified email addresses, increasing denial-of-service risk and compromising service integrity. | Tue 27 Oct |
| CVE-2026-19576 | 6.8 medium | 0.00% | no CPE yet | The Goodix GT9xx input driver in drivers/input/input_gt911.c reads the touch point count from the controller's status register and masks it with GT911_TOUCH_POINTS_MSK (0x0F), yielding a value of 0..15. In gt911_process() that value is used directly as the loop bound for filling point_reg[], a stack array sized to CONFIG_INPUT_GT911_MAX_TOUCH_POINTS, whose Kconfig range is 1..5 with a default of 1. No other check constrains the count; the driver relied only on a comment asserting that the controller had been programmed at init to report no more points than configured. Each loop iteration issues an I2C read of eight bytes straight into point_reg[i], so a controller that reports more points than the array holds causes up to 112 bytes of peer-supplied data to be written past the end of the array, over the stack frame of gt911_process() in the system workqueue thread. Two further loops then read out of bounds from the same array. Triggering it requires control of, or the ability to substitute, the I2C touch controller — plausible on the many supported boards where the GT9xx panel is a pluggable display module or shield rather than an on-PCB part; a spoofed device need only answer the init probes with a supported product ID and a checksum-valid config blob. The same overflow can also occur non-adversarially, with a GT9271-class panel that ignores the driver's touch-count programming and reports up to ten points, or with bus corruption of the single status byte. The impact is an out-of-bounds stack write with fully attacker-chosen content executing at kernel privilege, i.e. potential control-flow hijack on the host MCU, in addition to out-of-bounds reads and crashes. The attack vector is physical/local hardware access only; there is no network, USB, or syscall path to the defect. The fix clamps the reported count with min() against CONFIG_INPUT_GT911_MAX_TOUCH_POINTS before any array indexing. | 15 Oct |
| CVE-2026-107256 | unscored | 0.00% | drupal, shield | Improper Restriction of Excessive Authentication Attempts vulnerability in Drupal Shield allows Brute Force. This issue affects Shield versions: from 0.0.0 to 1.9.0. | Fri 30 Oct |
4 of 4
Download these 4 as CSV · subscribe to this list.
EPSS scores: 2026-10-31. NVD cursor: 2026-10-29 00:22. The News page shows only notable CVEs (KEV, your stack, new criticals, EPSS over 50%, or active exploitation per SSVC); this table has all of them.